BeagleBone Black Extracting eMMC contents

Jump to: navigation, search


There are lots of ways to extract the contents of the eMMC to save off and reuse. I'm proposing a method using Buildroot and an initramfs such that you can simply drop a few files from a .zip onto a normal, FAT-formatted SD card to perform the extraction. There are several things really handy here, such as the ability to edit to be whatever script you want to run on your board at boot. In the archive, I only have the necessary for saving your eMMC content. The flip-side is provided here in the text such that you need to go through a couple of steps before you trash your eMMC.

Steps to save

The steps for saving off your eMMC contents to a file:

  • Get a 4GB or larger uSD card that is FAT formatted.
  • Make sure that the partition on the uSD card is marked as active.
  • Download and extract the contents onto your uSD card.
  • Eject uSD card from your computer, insert into powered-off BeagleBone Black and apply power to your board while holding down the S2 button (release button a couple seconds after boot).

IMPORTANT: Due to the way the environment sets the partition mmcblk1, some newer boards (shipped with Debian 7.5 or newer) won't work with the As a workaround, instead of holding down the S2 button, just power the board with the uSD card inserted.

  • You'll notice USR0 (the LED closest to the S1 button in the corner) will (after about 20 seconds) start to blink steadily, rather than the double-pulse "heartbeat" pattern that is typical when your BeagleBone Black is running the typical Linux kernel configuration.
  • It'll run for a bit under 10 minutes and then USR0 will stay ON steady. That's your cue to remove power, remove the uSD card and put it back into your computer.
  • You should see a file called BeagleBoneBlack-eMMC-image-XXXXX.img.gz, where XXXXX is a set of random numbers. Save off this file to use for restoring your image later.

NOTE: Because the date won't be set on your board, you might want to adjust the date on the file to remember when you made it.

NOTE: Delete the file if you want to make room for a new backup image.

NOTE: If you plan to use Windows Win32 Disk Imager, you'll need to uncompress the image. It is compressed due to some FAT (non-FAT32) partitions not being able to store more than 2GB files.

NOTE: To mark a partition as active in Windows 7: Open command prompt and enter the following commands: diskpart -> list disk -> select disk x (where x is the uSD card) -> list partition -> select partition 1 (assuming the uSD card has 1 partition) -> active.

Performing restore/flashing

To restore the file, make sure there is a valid BeagleBoneBlack-eMMC-image-XXXX.img file on the uSD card and edit with your favorite text editor to contain the following:

echo timer > /sys/class/leds/beaglebone\:green\:usr0/trigger
gunzip -c /mnt/BBB-eMMC-XXXXX.img.gz | dd of=/dev/mmcblk1 bs=16M
UUID=$(/sbin/blkid -c /dev/null -s UUID -o value /dev/mmcblk1p2)
mkdir -p /mnt
mount /dev/mmcblk1p2 /mnt
sed -i "s/^uuid=.*\$/uuid=$UUID/" /mnt/boot/uEnv.txt
umount /mnt
echo default-on > /sys/class/leds/beaglebone\:green\:usr0/trigger

NOTE: Be certain to replace the 'XXXXX' above with the proper name of your image file.

NOTE: You can share and use other people's image files, but be sure to have them uncompressed on the card or add decompression to the script.

NOTE: The UUID replacement is required for recent Debian images. If you have something other than a 2 partition image, you might need to adjust or remove the lines that configure the UUID. They should be generally safe, but be aware that the newer u-boots that ship with BeagleBone Black attempt to use the UUID and pointing the '/dev/mmcblk1p2' to the right root partition is important.

NOTE: if you have difficulty booting a Rev. C BBB with this tool mount the SD card and make the following changes:

cd /mnt #or wherever you have mounted the card
mkdir dtbs
cp am335x-boneblack.dtb dtbs/am335x-boneblack.dtb

You may also try booting with the barrel jack (AC power) rather than the USB port.


This image was built using Buildroot. The sources are at with tag save-emmc-0.0.1. Download via or clone the git repo. It is a small fork from git:// tag e9f6011617528646768e69203e85fe64364b7efd.

Build steps

To build, 'make beagleboneblack_defconfig; make; ./'. Output files (am335x-boneblack.dtb, MLO, u-boot.img and uImage) will be in the output/images subdirectory. The following files were created manually.


optargs=quiet capemgr.disable_partno=BB-BONELT-HDMI,BB-BONELT-HDMIN
uenvcmd=load mmc 0 ${loadaddr} uImage;run loadfdt;setenv bootargs console=${console} ${optargs};bootm ${loadaddr} - ${fdtaddr}

echo timer > /sys/class/leds/beaglebone\:green\:usr0/trigger¡

#un-comment the following 2 lines to perform a backup
dd if=/dev/mmcblk1 bs=16M | gzip -c > $IMAGEFILE

#un-comment the following 6 lines to perform a restore (be sure to replace XXXXX with your image name)
#gunzip -c /mnt/BBB-eMMC-XXXXX.img.gz | dd of=/dev/mmcblk1 bs=16M
#UUID=$(/sbin/blkid -c /dev/null -s UUID -o value /dev/mmcblk1p2)
#mkdir -p /mnt
#mount /dev/mmcblk1p2 /mnt
#sed -i "s/^uuid=.*\$/uuid=$UUID/" /mnt/boot/uEnv.txt
#umount /mnt

echo default-on > /sys/class/leds/beaglebone\:green\:usr0/trigger

Other sources used

The kernel is based on, but I applied the patches, added firmware and uploaded it to to pull down in the Buildroot makefile. The link to the source for the firmware is in the commit.