Difference between revisions of "R-Car/Boards/Stout:Hardware"
(Created page with "{{TOC right}} This page contains information on R-Car H2 Stout board hardware. == Board Layout == 800px|Top view<br/> Fi...") |
|||
(4 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
{{TOC right}} | {{TOC right}} | ||
− | This page contains information on [[R- | + | This page contains information on [[R-Car/Boards/Stout | R-Car H2 Start.Now ("Stout") board]] hardware. |
== Board Layout == | == Board Layout == | ||
− | [[File: | + | [[File:StoutTopWithLabels.png|800px|Top view]]<br/> |
− | [[File: | + | [[File:StoutBottomWithLabels.png|800px|Bottom view]]<br/> |
== Power socket == | == Power socket == |
Latest revision as of 11:09, 3 July 2015
This page contains information on R-Car H2 Start.Now ("Stout") board hardware.
Board Layout
Power socket
Use 15 V power supply with two pins plug (FRIWO Texas plug, http://www.friwo-shop.de/en/accessories/secondary-adapters/194/texas-plug?c=7383 ). The power supply should be able to provide 15V with max 1.2A. Voltage input range is higher (12V to 18V) Pin 2 - VCC, pin 1 - GND
On-Board Memory/Storage
RAM: DDR3 SDRAM
The Renesas R-Car H2 Stout board DDR3-1600 RAM is organised into four 4-Gbit DDR3-SDRAMs (2 channels x 32 bit).
Flash: 64 MB SPI
64 MB Spansion S25FL512S SPI Flash. Maximum clock rate for SPI is 48.75 MHz.
Switches and Buttons
- SW1 - Power on/off button. For switching power on push button shortly. Press for >4sec – for power off
- SW2 - RESET button
- SWC1__8 - Dip switch 8x. SWC[8] - off = on board qspi flash, on = external qspi flash
- SW5 switch settings must be default (OFF OFF). The SW5 is for internal use only. Different switch setting
disables the JTAG debug mode
Connectors
Video Out
R-Car H2 incorporates three display units (DUs). DU0 and DU1/DU2 can be connected with the LVDS interface. DU0/DU1/DU3 can be connected with the digital RGB interface. DU2 can be connected to a LCD panel with TCON module.
HDMI
Digital RGB888 signal from R-Car H2 is connected to Analog Devices ADV7511 HDMI transmitter. Internal registers of ADV7511 are accessible via I2C interface (slave addresses: 0x72 for writring, 0x73 for reading).
The following displays have been tested with Stout board: TBD
Video In
R-Car H2's video input 0 (VIN0) is directly connected with the video input plug. R-Car H2's video input interface supports ITU-R BT.601, ITU-R BT.656, ITU-R BT.709, ITU-R BT.1358 There is the connector (SAMTEC FTSH-117-01-F-DH [ https://www.samtec.com/ftppub/pdf/ftsh_smt.pdf ]) on board for video input.
1 | VCC CAM0 3V3 | 2 | VCC CAM0 3V3 |
3 | VIN0 | 4 | VIN1 |
5 | VIN2 | 6 | VIN3 |
7 | VIN4 | 8 | VIN5 |
9 | VIN6 | 10 | VIN7 |
11 | VIN8 | 12 | VIN9 |
13 | VIN10 | 14 | VIN11 |
15 | GND | 16 | GND |
17 | VIN0 HSYNC | 18 | GND |
19 | VIN0 VSYNC | 20 | GND |
21 | VIN0 FIELD | 22 | GND |
23 | VIN0 CLKENB | 24 | GND |
25 | VIN0 CLK | 26 | GND |
27 | I2C SCL | 28 | GND |
29 | I2C SDA | 30 | GND |
31 | PWER DOWN | 32 | GND |
33 | CLK CAM0 25MHZ | 34 | GND |
JTAG (CN11)
The R-Car H2 Stout board incorporates a 20-pin connector for connection to the ARM JTAG emulator. TCK, TDI and TMS have 1.8V pull-up resistors 10kΩ. TRST_N have 1.8V pull-up resistors 4.7kΩ JTAG connector - SAMTEC FTSH_110_01_L_DV [1] JTAG interface is powered with 1.8V.
1 | ARM VTREF | 2 | ARM_TMS |
3 | GND | 4 | ARM TCK |
5 | GND | 6 | ARM TDO |
7 | GND | 8 | ARM TDI |
9 | GND | 10 | ARM TDI |
11 | n.u. | 12 | n.u. |
13 | n.u. | 14 | n.u. |
15 | GND | 16 | ARM TRST_N |
17 | GND | 18 | ASEBRK |
19 | GND | 20 | ARM PRESETOUT |
Debug Ethernet (CN10)
R-Car H2 Stout board includes one 100 Mbps Ethernet interface for debugging purposes. Micrel KSZ8041 PHY is used, in RMII mode.
Storage
microSD Card Slot
MicroSD card slot is connected to SD card host interface SDHI0 of R-Car H2. Micro SD voltage is 3.3V.
USB 2.0
TBD
440 pin connector
There is 440 pin connector for custom extension boards. This connector provides access to following R-Car H2 Soc functions:
- RMII 100Mbps, RGMII 1Gbps
- USB 2.0, 3.0
- QSPI, SPI
- PCIE
- LVDS DU0 / DU1
- UART, CAN
- Video inputs
Some pins are shared between 440 pin connector and other connectors thru several multiplexers. For more information about it? please visit this page R-Car/Boards/Stout:CPLD There is the pinout for 440-pin connector in the File:R20UH0001ED0000 UM start.now.pdf Appendix 4.2