Difference between revisions of "U-boot musb gadget support"
(Add issues section) |
|||
Line 45: | Line 45: | ||
Now when you plug the device into your Linux host machine you should be able to talk over serial using minicom,putty,etc over /dev/ttyACM0. | Now when you plug the device into your Linux host machine you should be able to talk over serial using minicom,putty,etc over /dev/ttyACM0. | ||
+ | |||
+ | === Issues === | ||
+ | |||
+ | Network Manager will see this device as a modem and attempt to send it AT commands. To avoid this, edit /lib/udev/rules.d/77-nm-probe-modem-capabilities.rules and add the following lines: | ||
+ | |||
+ | ATTRS{idVendor}=="0525", ATTRS{idProduct}=="a4a7", GOTO="nm_modem_probe_end" | ||
+ | ATTRS{idVendor}=="0525", ATTRS{idProduct}=="a4aa", GOTO="nm_modem_probe_end" | ||
+ | |||
+ | Directly after the last line with a 'GOTO="nm_modem_probe_end"' statement. | ||
+ | |||
+ | Minicom doesn't work so well if the device drops out from beneath it. Check out [http://gitorious.org/projects/clonetty clonetty] for a workaround. |
Revision as of 08:25, 2 April 2009
The code for musb gadget support is currently available on the omap3-dev-usb branch of the Beagle U-Boot git repository.
Contents
Current Status
- Currently the code enables the Beagleboard to be recognized as a USB ACM modem, and provides a u-boot console over it. It keeps the console over serial as well.
Known bugs
- None
Next steps
- Merge in mainstream?
- Prepare inf driver for Windows
Getting the source code
Checkout the git source for the musb gadget support from the Beagle U-Boot git repository. Get it by:
git clone git://www.sakoman.net/git/u-boot-omap3.git cd u-boot-omap3 git checkout --track -b omap3-dev-usb origin/omap3-dev-usb
Build (assuming Code Sourcery GCC 2007q3):
make CROSS_COMPILE=arm-none-linux-gnueabi- mrproper make CROSS_COMPILE=arm-none-linux-gnueabi- omap3_beagle_config make CROSS_COMPILE=arm-none-linux-gnueabi-
Getting started
- Load your new u-boot.bin image into the board using any of the existing methods. If you have a beagle running already a working u-boot, you can load it by serial using the 'loady' command and minicom or 'sb' (be sure to have lszrz installed in your distro). Then erasing the u-boot in flash and reflashing the new image with the following commands:
nand unlock nand erase 80000 160000 nand write.i 80000000 80000 160000 #(depending on the your configuration, your start address might be 82000000)
WARNING: in the previous instructions, please verified that your u-boot image was loaded on the address 80000000 (the last line from the ymodem transmission says where the image was loaded). On some boards I have see it uploads to 82000000 instead of 80000000
- Reboot your board
- Attach a mini-b USB cable to the beagle. Your host should recognize an ACM CDC device (works out of the box on Linux and OS X).
- If you want to have the u-boot console over USB use the following command:
setenv usbtty=cdc_acm saveenv
Then reboot, then:
setenv stdout usbtty,serial; setenv stdin usbtty,serial; setenv stderr usbtty,serial; saveenv
Now when you plug the device into your Linux host machine you should be able to talk over serial using minicom,putty,etc over /dev/ttyACM0.
Issues
Network Manager will see this device as a modem and attempt to send it AT commands. To avoid this, edit /lib/udev/rules.d/77-nm-probe-modem-capabilities.rules and add the following lines:
ATTRS{idVendor}=="0525", ATTRS{idProduct}=="a4a7", GOTO="nm_modem_probe_end" ATTRS{idVendor}=="0525", ATTRS{idProduct}=="a4aa", GOTO="nm_modem_probe_end"
Directly after the last line with a 'GOTO="nm_modem_probe_end"' statement.
Minicom doesn't work so well if the device drops out from beneath it. Check out clonetty for a workaround.