Talk:R-Car/Boards/Yocto-Gen3-ADAS

From eLinux.org
Jump to: navigation, search

Contents

Thread titleRepliesLast modified
Support for BroadR Expansion board with BCM89810 PHY002:26, 12 November 2020
About meta-rcar for Yocto v3.21.0018:00, 11 March 2020
git clone, meta-renesas & meta-rcar221:15, 30 September 2018
About version 2.23.0 or 2.23.1 ( for HAD Solution Kit)023:16, 14 December 2017
How to know minor update information of LinuxBSP?100:46, 15 September 2017
Flashing firmware (HAD Solution Kit)000:45, 15 September 2017

Support for BroadR Expansion board with BCM89810 PHY

Hello.

Question: is there support for BCM89810 PHY and any driver for the BroadR Expansion board available?

Story:on the board V3H 1.1 we need to connect external Ethernet Transceiver, BroadR Expansion board with BCM89810 PHY. Unfortunately, the Linux provided by Yocto does not include a PHY driver for the BCM89810. And by default kernel log says "Generic PHY" is used, however the BroadR Expansion board has a BCM89810 PHY and error happens: [ 722.692976] Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL) [ 722.706407] IPv6: ADDRCONF: eth1: link is not ready

Sincerely, Yaroslav

02:26, 12 November 2020

About meta-rcar for Yocto v3.21.0

Hello.


I have a question about meta-rcar (OpenEmbedded / Yocto BSP layer for Renesas Electronics's SoCs).


The meta-rcar for Yocto v3.21.0 seems to be updated frequently now.

If you plan to stop updating, when are you planning to do so?

Stopping updates means setting a branch, for example, BSP v5 for Yocto v3.19.0.

17:58, 11 March 2020

git clone, meta-renesas & meta-rcar

$ git clone git://github.com/renesas-rcar/meta-renesas
$ git clone git://github.com/CogentEmbedded/meta-rcar.git

When the above command is executed, the following message appears.
I can't be downloaded meta-renesas and meta-rcar.



Cloning into 'meta-renesas' ...
2018/09/06 18:25:20 socat [4374] E CONNECT github.com: 9418: Found
fatal: Could not read from remote repository.

Please make sure you have the correct access rights
and the repository exists.




Could you tell me how to solve it?

On the other hand, these are fine.
$ git clone git://git.yoctoproject.org/poky
$ git clone git://git.openembedded.org/meta-openembedded
$ git clone git://git.linaro.org/openembedded/meta-linaro.git

01:34, 6 September 2018

The command of A fails, but the command of B succeeds.
Is there something you noticed from this?

A: git clone git://github.com/renesas-rcar/meta-renesas
B: sudo git clone git://github.com/renesas-rcar/meta-renesas

Why do you think adding a "sudo" will succeed?

16:23, 19 September 2018

This problem was solved.

There was a problem with the internal network environment.

21:15, 30 September 2018
 
 

About version 2.23.0 or 2.23.1 ( for HAD Solution Kit)

Have you run HAD Solution Kit with version 2.23.0 or 2.23.1?

23:16, 14 December 2017

How to know minor update information of LinuxBSP?

Hello.

I built LinuxBSP for HAD solution kit in November 2016.
However, I heard that minor updates are progressing from December 2016 onwards.

Example: NVMe correspondence of SSD driver added, and etc.

Can you tell me what to check to see if LinuxBSP minor update was done?

18:33, 23 April 2017

The latest version has been improved, so it has already been solved.

00:46, 15 September 2017
 

Flashing firmware (HAD Solution Kit)

In HAD Solution Kit,

In the "Flashing firmware" you are informed that "You have to update R-Car H3SK or R-Car M3SK for the instructions on flashing firmware." Is it necessary to remove the Starter Kit? At that time, is it necessary to change the setting of Starter Kit? After booting with NFS, can not be rewritten by the method of rewriting with Linux flashcp command?

00:43, 15 September 2017