NOTICE: BL2: R-Car H3/M3/M3N Initial Program Loader(CA57) NOTICE: BL2: Initial Program Loader(Rev.2.0.4) NOTICE: BL2: PRR is R-Car H3 Ver.2.0 NOTICE: BL2: Board is Starter Kit Rev.1.0 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM [ 0.022197] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x53 NOTICE: BL2: DDR3200(rev.0.37) NOTICE: BL2: [COLD_BOOT] [ 0.000351] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x53 NOTICE: BL2: CH0: 0x400000000 - 0x440000000, 1 GiB NOTICE: BL2: CH1: 0x500000000 - 0x540000000, 1 GiB NOTICE: BL2: CH2: 0x600000000 - 0x640000000, 1 GiB NOTICE: BL2: CH3: 0x700000000 - 0x740000000, 1 GiB [ 0.039614] NOTICE: BL2: DRAM Split is 4ch [ 0.043758] NOTICE: BL2: QoS is default setting(rev.0.21) [ 0.049201] NOTICE: BL2: DRAM refresh interval 1.95 usec [ 0.054558] NOTICE: BL2: Periodic Write DQ Training NOTICE: BL2: Lossy Decomp areas NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570 NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0 NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0 [ 0.158250] ERROR: Image magic is wrong! [ 0.160857] ERROR: Bootloader partition 2 corrupted, setting unboot [ 0.167747] NOTICE: BL2: v1.5(release):a3c4725 [ 0.172089] NOTICE: BL2: Built : 16:45:55, Mar 30 2020 [ 0.177277] NOTICE: BL2: Normal boot [ 0.180912] NOTICE: BL2: eMMC boot from partition 1 [ 0.185829] NOTICE: BL2: Load dst=0xe632c100 src=(p:1)0x30000(384) len=0x200(1) [ 0.193347] NOTICE: BL2: Load dst=0x43f00000 src=(p:1)0x30400(386) len=0x1800(12) [ 0.201007] NOTICE: BL2: Load dst=0x44000000 src=(p:1)0x40000(512) len=0x10000(128) [ 0.209990] NOTICE: BL2: Load dst=0x44100000 src=(p:1)0x80000(1024) len=0x100000(2048) [ 0.239202] NOTICE: BL2: Load dst=0x50000000 src=(p:1)0x200000(4096) len=0x200000(4096) [ 0.291063] NOTICE: BL2: Booting BL31 U-Boot 2018.09-g74e87ec (Mar 30 2020 - 16:45:46 +0300) Config: r8a7795-h3ulcb-u-boot CPU: Renesas Electronics R8A7795 rev 2.0 Model: Renesas H3ULCB board based on r8a7795 ES2.0+ DRAM: 3.9 GiB Bank #0: 0x048000000 - 0x07fffffff, 896 MiB Bank #1: 0x500000000 - 0x53fffffff, 1 GiB Bank #2: 0x600000000 - 0x63fffffff, 1 GiB Bank #3: 0x700000000 - 0x73fffffff, 1 GiB MMC: sd@ee100000: 0, sd@ee140000: 1 Loading Environment from MMC... OK In: serial@e6e88000 Out: serial@e6e88000 Err: serial@e6e88000 Net: eth0: ethernet@e6800000 Setting bootmode 'android' Hit any key to stop autoboot: 0 => printenv baudrate=115200 bootargs=video=LVDS-1:d video=VGA-1:d init_time=1585791913 bootcmd=boota 1 boot 0x4C000000 avb bootdelay=3 bootmode=android ethact=ravb ethaddr=2e:09:0a:03:93:11 fdt_high=0xffffffffffffffff fdtcontroladdr=7d6e2448 initrd_high=0xffffffffffffffff loadaddr=0x58000000 platform=r8a7795 product=ulcb recovery=setenv bootmode recovery; run bootcmd; serialno=00025192 stderr=serial@e6e88000 stdin=serial@e6e88000 stdout=serial@e6e88000 ver=U-Boot 2018.09-g74e87ec (Mar 30 2020 - 16:45:46 +0300) Environment size: 504/131068 bytes => setenv bootargs =>setenv bootcmd =>setenv fdt_high =>setenv initrd_high =>setenv ethaddr 2e:09:0a:03:93:11 =>setenv ipaddr 192.168.0.2 =>setenv serverip 192.168.0.1 =>setenv bootargs 'consoleblank=0 console=ttySC0,115200 rw root=/dev/nfs nfsroot=192.168.0.1:/nfs/h3ulcb ip=192.168.0.2' =>tftp 0x48080000 /h3ulcb/Image Using ethernet@e6800000 device TFTP from server 192.168.0.1; our IP address is 192.168.0.2 Filename '/h3ulcb/Image'. Load address: 0x48080000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 18.4 MiB/s done Bytes transferred = 16497152 (fbba00 hex) =>tftp 0x48000000 /h3ulcb/Image-r8a7795-h3ulcb-kf.dtb Using ethernet@e6800000 device TFTP from server 192.168.0.1; our IP address is 192.168.0.2 Filename '/h3ulcb/Image-r8a7795-h3ulcb-kf.dtb'. Load address: 0x48000000 Loading: ####### 17.5 MiB/s done Bytes transferred = 91875 (166e3 hex) =>booti 0x48080000 - 0x48000000 ## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 Loading Device Tree to 0000000048066000, end 000000004807f6e2 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.75-ltsi-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Fri0 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+ [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000073fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x73ff6cd00-0x73ff6e7ff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000048000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000073fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff] [ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000500000000-0x000000053fffffff] [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff] [ 0.000000] node 0: [mem 0x0000000700000000-0x000000073fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS resident on physical CPU 0x0 [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu @ffff8006ffea7000 s57624 r8192 d32488 u98304 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 987840 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: androidboot.boottime=18.995 consoleblank=0 console=ttySC0,115200 rw root=/dev/nfs n2 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff] [ 0.000000] Memory: 3192800K/4014080K available (10364K kernel code, 686K rwdata, 4256K rodata, 768K init, 404K bss,) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB) [ 0.000000] .text : 0xffff000008080000 - 0xffff000008aa0000 ( 10368 KB) [ 0.000000] .rodata : 0xffff000008aa0000 - 0xffff000008ed0000 ( 4288 KB) [ 0.000000] .init : 0xffff000008ed0000 - 0xffff000008f90000 ( 768 KB) [ 0.000000] .data : 0xffff000008f90000 - 0xffff00000903ba00 ( 687 KB) [ 0.000000] .bss : 0xffff00000903ba00 - 0xffff0000090a0c10 ( 405 KB) [ 0.000000] fixed : 0xffff7dfffe7f9000 - 0xffff7dfffec00000 ( 4124 KB) [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum) [ 0.000000] 0xffff7e0000200000 - 0xffff7e001c000000 ( 446 MB actual) [ 0.000000] memory : 0xffff800008000000 - 0xffff800700000000 ( 28544 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125s [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns [ 0.000111] Console: colour dummy device 80x25 [ 0.000154] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) [ 0.000163] pid_max: default: 32768 minimum: 301 [ 0.000215] Security Framework initialized [ 0.001810] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.002628] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.002668] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002696] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.015931] ASID allocator initialised with 32768 entries [ 0.023924] Hierarchical SRCU implementation. [ 0.032724] Detected Renesas R-Car Gen3 r8a7795 ES2.0 [ 0.033503] EFI services will not be available. [ 0.039953] smp: Bringing up secondary CPUs ... [ 0.068141] Detected PIPT I-cache on CPU1 [ 0.068177] CPU1: Booted secondary processor [411fd073] [ 0.096148] Detected PIPT I-cache on CPU2 [ 0.096168] CPU2: Booted secondary processor [411fd073] [ 0.124178] Detected PIPT I-cache on CPU3 [ 0.124195] CPU3: Booted secondary processor [411fd073] [ 0.152225] CPU features: enabling workaround for ARM erratum 845719 [ 0.152234] Detected VIPT I-cache on CPU4 [ 0.152272] CPU4: Booted secondary processor [410fd034] [ 0.180245] Detected VIPT I-cache on CPU5 [ 0.180268] CPU5: Booted secondary processor [410fd034] [ 0.208278] Detected VIPT I-cache on CPU6 [ 0.208301] CPU6: Booted secondary processor [410fd034] [ 0.236314] Detected VIPT I-cache on CPU7 [ 0.236336] CPU7: Booted secondary processor [410fd034] [ 0.236409] smp: Brought up 1 node, 8 CPUs [ 0.236430] SMP: Total of 8 processors activated. [ 0.236436] CPU features: detected feature: 32-bit EL0 Support [ 0.236439] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.242651] CPU: All CPU(s) started at EL1 [ 0.242673] alternatives: patching kernel code [ 0.243395] devtmpfs: initialized [ 0.249718] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0 [ 0.250117] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.250173] futex hash table entries: 2048 (order: 6, 262144 bytes) [ 0.258221] pinctrl core: initialized pinctrl subsystem [ 0.259327] DMI not present or invalid. [ 0.259525] NET: Registered protocol family 16 [ 0.260666] cpuidle: using governor menu [ 0.260793] vdso: 2 pages (1 code @ ffff000008aa6000, 1 data @ ffff000008f95000) [ 0.260805] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.261441] DMA: preallocated 256 KiB pool for atomic allocations [ 0.261510] Serial: AMBA PL011 UART driver [ 0.264889] sh-pfc e6060000.pin-controller: r8a77951_pfc support registered [ 0.288589] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.289602] ACPI: Interpreter disabled. [ 0.291833] rcar-avs: use avs value: 0 [ 0.291953] rcar-avs: /cpus/cpu@0 is running with: /opp_table0 [ 0.291964] rcar-avs: /cpus/cpu@1 is running with: /opp_table0 [ 0.291972] rcar-avs: /cpus/cpu@2 is running with: /opp_table0 [ 0.291981] rcar-avs: /cpus/cpu@3 is running with: /opp_table0 [ 0.292004] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0 [ 0.293703] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved [ 0.294239] vgaarb: loaded [ 0.294402] SCSI subsystem initialized [ 0.294665] usbcore: registered new interface driver usbfs [ 0.294689] usbcore: registered new interface driver hub [ 0.294750] usbcore: registered new device driver usb [ 0.295583] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz [ 0.295881] media: Linux media interface: v0.10 [ 0.295903] Linux video capture interface: v2.00 [ 0.295963] pps_core: LinuxPPS API ver. 1 registered [ 0.295967] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.295976] PTP clock support registered [ 0.296279] EDAC MC: Ver: 3.0.0 [ 0.296447] dmi: Firmware registration failed. [ 0.296967] Advanced Linux Sound Architecture Driver Initialized. [ 0.297441] clocksource: Switched to clocksource arch_sys_counter [ 0.297737] VFS: Disk quotas dquot_6.6.0 [ 0.297776] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.297870] pnp: PnP ACPI: disabled [ 0.301524] thermal thermal_zone2: power_allocator: sustainable_power will be estimated [ 0.301622] NET: Registered protocol family 2 [ 0.302056] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.302262] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.302553] TCP: Hash tables configured (established 32768 bind 32768) [ 0.302670] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.302735] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.302883] NET: Registered protocol family 1 [ 0.303101] RPC: Registered named UNIX socket transport module. [ 0.303105] RPC: Registered udp transport module. [ 0.303108] RPC: Registered tcp transport module. [ 0.303112] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.304262] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.304791] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available [ 0.305203] kvm [1]: HYP mode not available [ 0.306875] audit: initializing netlink subsys (disabled) [ 0.306966] audit: type=2000 audit(0.303:1): state=initialized audit_enabled=0 res=1 [ 0.307218] workingset: timestamp_bits=44 max_order=20 bucket_order=0 [ 0.310575] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.310965] NFS: Registering the id_resolver key type [ 0.310983] Key type id_resolver registered [ 0.310987] Key type id_legacy registered [ 0.310996] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.311103] 9p: Installing v9fs 9p2000 file system support [ 0.312508] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.312516] io scheduler noop registered [ 0.312521] io scheduler deadline registered [ 0.312603] io scheduler cfq registered (default) [ 0.312608] io scheduler mq-deadline registered [ 0.312612] io scheduler kyber registered [ 0.316210] gpio_rcar e6050000.gpio: driving 16 GPIOs [ 0.316436] gpio_rcar e6051000.gpio: driving 29 GPIOs [ 0.316559] GPIO line 455 (BL PWM 100%) hogged as output/high [ 0.316658] gpio_rcar e6052000.gpio: driving 15 GPIOs [ 0.316863] gpio_rcar e6053000.gpio: driving 16 GPIOs [ 0.316975] GPIO line 432 (MOST RST) hogged as output/high [ 0.317070] gpio_rcar e6054000.gpio: driving 18 GPIOs [ 0.317299] gpio_rcar e6055000.gpio: driving 26 GPIOs [ 0.317418] GPIO line 381 (Onboard MCh Audio) hogged as output/high [ 0.317540] gpio_rcar e6055400.gpio: driving 32 GPIOs [ 0.317737] gpio_rcar e6055800.gpio: driving 4 GPIOs [ 0.318721] rcar-pcie fe000000.pcie: no pcie3v3 regulator found [ 0.318728] rcar-pcie fe000000.pcie: no pcie1v8 regulator found [ 0.318734] OF: PCI: host bridge /soc/pcie@fe000000 ranges: [ 0.318751] OF: PCI: IO 0xfe100000..0xfe1fffff -> 0x00000000 [ 0.318764] OF: PCI: MEM 0xfe200000..0xfe3fffff -> 0xfe200000 [ 0.318772] OF: PCI: MEM 0x30000000..0x37ffffff -> 0x30000000 [ 0.318777] OF: PCI: MEM 0x38000000..0x3fffffff -> 0x38000000 [ 0.385292] rcar-pcie fe000000.pcie: PCIe link down [ 0.386873] EINJ: ACPI disabled. [ 0.402412] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.403687] SuperH (H)SCI(F) driver initialized [ 0.404206] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 35, base_baud = 0) is a hscif [ 0.404800] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 36, base_baud = 0) is a hscif [ 0.405307] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 122, base_baud = 0) is a scif [ 0.405786] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 123, base_baud = 0) is a scif [ 1.519923] console [ttySC0] enabled [ 1.525354] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.531975] [drm] No driver support for vblank timestamp query. [ 1.538510] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY) [ 1.548371] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver [ 1.562119] loop: module loaded [ 1.568792] libphy: Fixed MDIO Bus: probed [ 1.573065] tun: Universal TUN/TAP device driver, 1.6 [ 1.578257] CAN device driver interface [ 1.582808] rcar_can e6c30000.can: device registered (IRQ120) [ 1.588960] rcar_can e6c38000.can: device registered (IRQ121) [ 1.595206] usbcore: registered new interface driver peak_usb [ 1.601370] thunder-xcv, ver 1.0 [ 1.604654] thunder-BGX, ver 1.0 [ 1.607906] thunder-nic, ver 1.0 [ 1.611520] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.617352] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.623294] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.630258] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.635852] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.643682] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.649753] sky2: driver version 1.30 [ 1.654256] libphy: ravb_mii: probed [ 1.658546] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:03:93:11, IRQ 117. [ 1.668147] VFIO - User Level meta-driver version: 0.3 [ 1.674314] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.680845] ehci-pci: EHCI PCI platform driver [ 1.685311] ehci-platform: EHCI generic platform driver [ 1.711913] ehci-platform ee080100.usb: EHCI Host Controller [ 1.717588] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1 [ 1.725544] ehci-platform ee080100.usb: irq 165, io mem 0xee080100 [ 1.745451] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10 [ 1.751963] hub 1-0:1.0: USB hub found [ 1.755730] hub 1-0:1.0: 1 port detected [ 1.760011] ehci-platform ee0a0100.usb: EHCI Host Controller [ 1.765678] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2 [ 1.773620] ehci-platform ee0a0100.usb: irq 166, io mem 0xee0a0100 [ 1.793452] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 [ 1.799888] hub 2-0:1.0: USB hub found [ 1.803652] hub 2-0:1.0: 1 port detected [ 1.807856] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.814048] ohci-pci: OHCI PCI platform driver [ 1.818537] ohci-platform: OHCI generic platform driver [ 1.824073] ohci-platform ee080000.usb: Generic Platform OHCI controller [ 1.830785] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3 [ 1.838682] ohci-platform ee080000.usb: irq 165, io mem 0xee080000 [ 1.931712] hub 3-0:1.0: USB hub found [ 1.935476] hub 3-0:1.0: 1 port detected [ 1.939685] ohci-platform ee0a0000.usb: Generic Platform OHCI controller [ 1.946397] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4 [ 1.954293] ohci-platform ee0a0000.usb: irq 166, io mem 0xee0a0000 [ 2.047691] hub 4-0:1.0: USB hub found [ 2.051455] hub 4-0:1.0: 1 port detected [ 2.056013] xhci-hcd ee000000.usb: xHCI Host Controller [ 2.061248] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5 [ 2.084653] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830010 [ 2.093811] xhci-hcd ee000000.usb: irq 164, io mem 0xee000000 [ 2.099908] hub 5-0:1.0: USB hub found [ 2.103673] hub 5-0:1.0: 1 port detected [ 2.107734] xhci-hcd ee000000.usb: xHCI Host Controller [ 2.112967] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6 [ 2.120367] xhci-hcd ee000000.usb: Host supports USB 3.0 SuperSpeed [ 2.126757] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.135096] hub 6-0:1.0: USB hub found [ 2.138865] hub 6-0:1.0: 1 port detected [ 2.143215] usbcore: registered new interface driver usb-storage [ 2.150867] renesas_usbhs e6590000.usb: no transceiver found [ 2.156603] renesas_usbhs e6590000.usb: gadget probed [ 2.161779] renesas_usbhs e6590000.usb: probed [ 2.167492] i2c /dev entries driver [ 2.178263] cs2000-cp 2-004f: revision - C1 [ 2.182605] pca953x 2-0074: 2-0074 supply vcc not found, using dummy regulator [ 2.199490] GPIO line 346 (HUB pwen) hogged as output/high [ 2.206093] GPIO line 347 (HUB rst) hogged as output/high [ 2.212605] GPIO line 348 (OTG OFFVBUSn) hogged as output/low [ 2.219465] GPIO line 349 (OTG EXTLPn) hogged as output/high [ 2.226237] GPIO line 355 (pcm3168a reset) hogged as output/high [ 2.232525] pca953x 2-0075: 2-0075 supply vcc not found, using dummy regulator [ 2.242056] random: fast init done [ 2.252732] GPIO line 330 (GPS rst) hogged as output/high [ 2.259244] GPIO line 333 (FPDLink shdn) hogged as output/high [ 2.265948] i2c-rcar e6510000.i2c: probed [ 2.276101] pca953x 4-0076: 4-0076 supply vcc not found, using dummy regulator [ 2.286735] GPIO line 308 (Video-B A0) hogged as output/low [ 2.292718] GPIO line 309 (Video-B A1) hogged as output/high [ 2.298784] GPIO line 310 (Video-A A0) hogged as output/low [ 2.304767] GPIO line 311 (Video-A A1) hogged as output/high [ 2.310833] GPIO line 316 (CMOS PWDN) hogged as output/high [ 2.316815] GPIO line 317 (CMOS RST) hogged as output/high [ 2.322708] GPIO line 318 (RaspB_IO1) hogged as output/high [ 2.328691] GPIO line 319 (RaspB_IO0) hogged as output/high [ 2.334672] GPIO line 312 (SAM RST) hogged as output/high [ 2.340477] GPIO line 313 (SAM PWR) hogged as output/low [ 2.346196] GPIO line 322 (LVDS switch) hogged as output/high [ 2.352461] pca953x 4-0077: 4-0077 supply vcc not found, using dummy regulator [ 2.363075] GPIO line 292 (mPCIe WAKE#) hogged as output/low [ 2.369141] GPIO line 293 (mPCIe W_DISABLE) hogged as output/high [ 2.375518] GPIO line 294 (mPCIe CLKREQ#) hogged as input [ 2.381205] GPIO line 295 (mPCIe OVC) hogged as input [ 2.386768] i2c-rcar e66d8000.i2c: probed [ 2.391936] i2c i2c-2: Added multiplexed i2c bus 9 [ 2.396870] i2c i2c-2: Added multiplexed i2c bus 10 [ 2.401860] i2c i2c-2: Added multiplexed i2c bus 11 [ 2.406847] i2c i2c-2: Added multiplexed i2c bus 12 [ 2.411962] adv7511 13-003d: 13-003d supply avdd not found, using dummy regulator [ 2.419477] adv7511 13-003d: 13-003d supply dvdd not found, using dummy regulator [ 2.426981] adv7511 13-003d: 13-003d supply pvdd not found, using dummy regulator [ 2.434498] adv7511 13-003d: 13-003d supply bgvdd not found, using dummy regulator [ 2.442086] adv7511 13-003d: 13-003d supply dvdd-3v not found, using dummy regulator [ 2.473448] i2c i2c-2: Added multiplexed i2c bus 13 [ 2.478464] i2c i2c-2: Added multiplexed i2c bus 14 [ 2.484251] edt_ft5x06 15-0038: touchscreen probe failed [ 2.489601] i2c i2c-2: Added multiplexed i2c bus 15 [ 2.494791] i2c i2c-2: Added multiplexed i2c bus 16 [ 2.499673] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548 [ 2.507647] i2c i2c-4: Added multiplexed i2c bus 17 [ 2.512998] i2c i2c-4: Added multiplexed i2c bus 18 [ 2.517994] i2c i2c-4: Added multiplexed i2c bus 19 [ 2.522985] i2c i2c-4: Added multiplexed i2c bus 20 [ 2.528036] i2c i2c-4: Added multiplexed i2c bus 21 [ 2.533087] i2c i2c-4: Added multiplexed i2c bus 22 [ 2.538066] i2c i2c-4: Added multiplexed i2c bus 23 [ 2.543171] pca953x 24-0026: 24-0026 supply vcc not found, using dummy regulator [ 2.550779] pca953x 24-0026: failed reading register [ 2.556051] dummy 24-006c: failed reading [ 2.560152] i2c i2c-4: Added multiplexed i2c bus 24 [ 2.565033] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548 [ 2.573044] ov5642 22-003c: reg_write: i2c write error, reg: 3103 [ 2.579465] ov5647_read: i2c read error, reg: 100 [ 2.584171] ov5647 21-0036: Camera not available, check power [ 2.590010] ov5647_read: i2c read error, reg: 300a [ 2.594803] ov5647 21-0036: OV5647 not found! [ 2.701835] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.731310] hub 6-1:1.0: USB hub found [ 2.735369] hub 6-1:1.0: 4 ports detected [ 2.850054] ov106xx 18-0060: deserializer does not present [ 2.855583] ov106xx 18-0060: deserializer does not present for OV495 [ 2.861980] ov106xx 18-0060: deserializer does not present for OV10640 [ 2.868555] ov106xx 18-0060: deserializer does not present for OV2311 [ 2.875036] ov106xx 18-0060: deserializer does not present for OV10635 [ 2.881608] ov106xx 18-0060: deserializer does not present for OV490 [ 2.885446] usb 5-1: new high-speed USB device number 2 using xhci-hcd [ 2.894526] ov106xx 18-0060: deserializer does not present for AR0132 [ 2.901009] ov106xx 18-0060: deserializer does not present for AR0140 [ 2.907491] ov106xx 18-0060: deserializer does not present for AR0143 [ 2.913971] ov106xx 18-0060: deserializer does not present for AR0147 [ 2.930510] ov106xx 18-0060: read fail: chip 0x60 register 0x3000: -6 [ 2.936989] ov106xx 18-0060: deserializer does not present [ 2.942513] ov106xx 18-0060: deserializer does not present for AP0101 [ 2.948990] ov106xx 18-0060: deserializer does not present for GW4200 [ 2.955502] ov106xx 18-0060: deserializer does not present [ 2.961024] ov106xx 18-0060: deserializer does not present [ 2.966547] ov106xx 18-0060: deserializer does not present [ 2.972071] ov106xx 18-0060: deserializer does not present for ISX016 [ 2.978547] ov106xx 18-0060: deserializer does not present for ISX019 [ 2.984989] ov106xx 18-0060: failed to probe @ 0x60 (i2c-4-mux (chan_id 1)) [ 2.991957] ov106xx: probe of 18-0060 failed with error -22 [ 2.997684] ov106xx 18-0061: deserializer does not present [ 3.003208] ov106xx 18-0061: deserializer does not present for OV495 [ 3.009599] ov106xx 18-0061: deserializer does not present for OV10640 [ 3.016164] ov106xx 18-0061: deserializer does not present for OV2311 [ 3.022640] ov106xx 18-0061: deserializer does not present for OV10635 [ 3.029207] ov106xx 18-0061: deserializer does not present for OV490 [ 3.035598] ov106xx 18-0061: deserializer does not present for AR0132 [ 3.038926] hub 5-1:1.0: USB hub found [ 3.039239] hub 5-1:1.0: 4 ports detected [ 3.049855] ov106xx 18-0061: deserializer does not present for AR0140 [ 3.056340] ov106xx 18-0061: deserializer does not present for AR0143 [ 3.062822] ov106xx 18-0061: deserializer does not present for AR0147 [ 3.079364] ov106xx 18-0061: read fail: chip 0x61 register 0x3000: -6 [ 3.085846] ov106xx 18-0061: deserializer does not present [ 3.091368] ov106xx 18-0061: deserializer does not present for AP0101 [ 3.097844] ov106xx 18-0061: deserializer does not present for GW4200 [ 3.104360] ov106xx 18-0061: deserializer does not present [ 3.109885] ov106xx 18-0061: deserializer does not present [ 3.115406] ov106xx 18-0061: deserializer does not present [ 3.120928] ov106xx 18-0061: deserializer does not present for ISX016 [ 3.127404] ov106xx 18-0061: deserializer does not present for ISX019 [ 3.133848] ov106xx 18-0061: failed to probe @ 0x61 (i2c-4-mux (chan_id 1)) [ 3.140819] ov106xx: probe of 18-0061 failed with error -22 [ 3.146557] ov106xx 18-0062: deserializer does not present [ 3.152081] ov106xx 18-0062: deserializer does not present for OV495 [ 3.158472] ov106xx 18-0062: deserializer does not present for OV10640 [ 3.165038] ov106xx 18-0062: deserializer does not present for OV2311 [ 3.171515] ov106xx 18-0062: deserializer does not present for OV10635 [ 3.178083] ov106xx 18-0062: deserializer does not present for OV490 [ 3.184473] ov106xx 18-0062: deserializer does not present for AR0132 [ 3.190952] ov106xx 18-0062: deserializer does not present for AR0140 [ 3.197431] ov106xx 18-0062: deserializer does not present for AR0143 [ 3.203914] ov106xx 18-0062: deserializer does not present for AR0147 [ 3.220450] ov106xx 18-0062: read fail: chip 0x62 register 0x3000: -6 [ 3.226932] ov106xx 18-0062: deserializer does not present [ 3.232453] ov106xx 18-0062: deserializer does not present for AP0101 [ 3.238929] ov106xx 18-0062: deserializer does not present for GW4200 [ 3.245448] ov106xx 18-0062: deserializer does not present [ 3.250969] ov106xx 18-0062: deserializer does not present [ 3.256490] ov106xx 18-0062: deserializer does not present [ 3.262013] ov106xx 18-0062: deserializer does not present for ISX016 [ 3.268487] ov106xx 18-0062: deserializer does not present for ISX019 [ 3.274929] ov106xx 18-0062: failed to probe @ 0x62 (i2c-4-mux (chan_id 1)) [ 3.281894] ov106xx: probe of 18-0062 failed with error -22 [ 3.287616] ov106xx 18-0063: deserializer does not present [ 3.293139] ov106xx 18-0063: deserializer does not present for OV495 [ 3.299531] ov106xx 18-0063: deserializer does not present for OV10640 [ 3.306096] ov106xx 18-0063: deserializer does not present for OV2311 [ 3.312572] ov106xx 18-0063: deserializer does not present for OV10635 [ 3.319140] ov106xx 18-0063: deserializer does not present for OV490 [ 3.325531] ov106xx 18-0063: deserializer does not present for AR0132 [ 3.332009] ov106xx 18-0063: deserializer does not present for AR0140 [ 3.338487] ov106xx 18-0063: deserializer does not present for AR0143 [ 3.344965] ov106xx 18-0063: deserializer does not present for AR0147 [ 3.361500] ov106xx 18-0063: read fail: chip 0x63 register 0x3000: -6 [ 3.367978] ov106xx 18-0063: deserializer does not present [ 3.373501] ov106xx 18-0063: deserializer does not present for AP0101 [ 3.379976] ov106xx 18-0063: deserializer does not present for GW4200 [ 3.386488] ov106xx 18-0063: deserializer does not present [ 3.392010] ov106xx 18-0063: deserializer does not present [ 3.397531] ov106xx 18-0063: deserializer does not present [ 3.403053] ov106xx 18-0063: deserializer does not present for ISX016 [ 3.409527] ov106xx 18-0063: deserializer does not present for ISX019 [ 3.415968] ov106xx 18-0063: failed to probe @ 0x63 (i2c-4-mux (chan_id 1)) [ 3.422934] ov106xx: probe of 18-0063 failed with error -22 [ 3.429365] rcar_csi2 fea80000.csi2: Data lanes 2, link freq 280 [ 3.435561] rcar_csi2 feaa0000.csi2: Data lanes 4, link freq 300 [ 3.450383] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values [ 3.462087] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points [ 3.473303] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points [ 3.483644] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points [ 3.492402] sdhci: Secure Digital Host Controller Interface driver [ 3.498591] sdhci: Copyright(c) Pierre Ossman [ 3.503681] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO [ 3.569551] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz [ 3.579150] Synopsys Designware Multimedia Card Interface Driver [ 3.585698] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.592554] ledtrig-cpu: registered to indicate activity on CPUs [ 3.599253] usbcore: registered new interface driver usbhid [ 3.604827] usbhid: USB HID core driver [ 3.608673] mostcore: init() [ 3.611626] aim_cdev: init() [ 3.614535] mostcore: registered new application interfacing module cdev [ 3.621247] mostcore: registered new application interfacing module networking [ 3.628467] aim_sound: init() [ 3.631442] mostcore: registered new application interfacing module sound [ 3.638249] mostcore: registered new application interfacing module v4l [ 3.645449] optee: probing for conduit method from DT. [ 3.650785] optee driver R-Car Rev.1.0.10 [ 3.654918] optee: initialized driver [ 3.670579] rcar_sound ec500000.sound: probed [ 3.675273] NET: Registered protocol family 17 [ 3.679733] can: controller area network core (rev 20170425 abi 9) [ 3.685989] NET: Registered protocol family 29 [ 3.690478] can: raw protocol (rev 20170425) [ 3.694765] can: broadcast manager protocol (rev 20170425 t) [ 3.700486] 9pnet: Installing 9P2000 support [ 3.704817] Key type dns_resolver registered [ 3.709533] registered taskstats version 1 [ 3.718269] thermal emergency: set temperature to 110 celsius [ 3.724221] thermal emergency: shutdown target cpus 1-7 [ 3.729465] thermal emergency: freq scaled target cpus 0 [ 3.735071] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs [ 3.748581] mmc0: new HS400 MMC card at address 0001 [ 3.753916] mmcblk0: mmc0:0001 8GSD4R 7.28 GiB [ 3.758656] mmcblk0boot0: mmc0:0001 8GSD4R partition 1 31.9 MiB [ 3.764662] mmcblk0boot1: mmc0:0001 8GSD4R partition 2 31.9 MiB [ 3.770780] mmcblk0rpmb: mmc0:0001 8GSD4R partition 3 512 KiB, chardev (240:0) [ 3.780816] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 3.957458] OF: PCI: host bridge /soc/pcie@ee800000 ranges: [ 3.963055] OF: PCI: IO 0xee900000..0xee9fffff -> 0x00000000 [ 3.968981] OF: PCI: MEM 0xeea00000..0xeebfffff -> 0xeea00000 [ 3.974902] OF: PCI: MEM 0xc0000000..0xc7ffffff -> 0xc0000000 [ 3.980821] OF: PCI: MEM 0xc8000000..0xcfffffff -> 0xc8000000 [ 4.053068] rcar-pcie ee800000.pcie: PCIe link down [ 4.060939] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.067566] [drm] No driver support for vblank timestamp query. [ 4.076013] bd9571mwv 7-0030: Device: BD9571MWV rev. 1 [ 4.085842] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO [ 4.153853] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz [ 4.225523] renesas_sdhi_internal_dmac ee160000.sd: mmc2 base at 0xee160000 max clock rate 50 MHz [ 4.247748] asoc-audio-graph-card sound@0: pcm3168a <-> rsnd-dai.0 mapping ok [ 4.254904] asoc-audio-graph-card sound@0: ASoC: no DMI vendor name! [ 4.262841] asoc-audio-graph-card sound@1: ak4613-hifi <-> rsnd-dai.1 mapping ok [ 4.270264] asoc-audio-graph-card sound@1: ASoC: no DMI vendor name! [ 4.279263] asoc-audio-graph-card sound@2: si468x-pcm <-> rsnd-dai.2 mapping ok [ 4.286581] asoc-audio-graph-card sound@2: ASoC: no DMI vendor name! [ 4.297290] asoc-audio-graph-card sound@3: wl18xx-pcm <-> rsnd-dai.3 mapping ok [ 4.304618] asoc-audio-graph-card sound@3: ASoC: no DMI vendor name! [ 4.311337] renesas_sdhi_internal_dmac ee160000.sd: card claims to support voltages below defined range [ 4.321628] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.328244] [drm] No driver support for vblank timestamp query. [ 4.348848] mmc2: new high speed SDIO card at address 0001 [ 4.397554] Console: switching to colour frame buffer device 160x50 [ 4.427680] rcar-du feb00000.display: fb0: frame buffer device [ 4.434023] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0 [ 4.441770] [drm] Device feb00000.display probed [ 4.447454] input: keyboard as /devices/platform/keyboard/input/input1 [ 4.454260] hctosys: unable to open rtc device (rtc0) [ 4.532595] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PH) [ 7.221477] ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 7.253449] IP-Config: Guessing netmask 255.255.255.0 [ 7.258500] IP-Config: Complete: [ 7.261728] device=eth0, hwaddr=2e:09:0a:03:93:11, ipaddr=192.168.0.2, mask=255.255.255.0, gw=255.255.255.255 [ 7.272072] host=192.168.0.2, domain=, nis-domain=(none) [ 7.277816] bootserver=255.255.255.255, rootserver=192.168.0.1, rootpath= [ 7.285409] SDHI3 VccQ: disabling [ 7.288732] PCM3168A Vcc Vdd: disabling [ 7.292568] SDHI0 Vcc: disabling [ 7.295797] wlan-en-regulator: disabling [ 7.299724] SDHI3 Vcc: disabling [ 7.302953] amp-en-regulator: disabling [ 7.306790] SDHI0 VccQ: disabling [ 7.310106] ALSA device list: [ 7.313066] #0: pcm3168a [ 7.315771] #1: ak4613 [ 7.318301] #2: radio [ 7.320740] #3: wl18xx [ 7.323554] md: Skipping autodetection of RAID arrays. (raid=autodetect will force) [ 9.376015] VFS: Mounted root (nfs filesystem) on device 0:15. [ 9.382074] devtmpfs: mounted [ 9.385432] Freeing unused kernel memory: 768K [ 9.462124] systemd[1]: System time before build time, advancing clock. [ 9.490299] NET: Registered protocol family 10 [ 9.495494] Segment Routing with IPv6 [ 9.510157] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +U) [ 9.531447] systemd[1]: Detected architecture arm64. Welcome to Poky (Yocto Project Reference Distro) 2.4.3 (rocko)! [ 9.553880] systemd[1]: Set hostname to . [ 9.758288] random: systemd: uninitialized urandom read (16 bytes read) [ 9.765028] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 9.781756] random: systemd: uninitialized urandom read (16 bytes read) [ 9.788638] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 9.813532] random: systemd: uninitialized urandom read (16 bytes read) [ 9.820188] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 9.841731] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.861605] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 9.885604] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 9.909561] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Audit Socket. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Paths. [ OK ] Listening on Syslog Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Created slice System Slice. Starting Journal Service... Mounting Kernel Debug File System... [ OK ] Reached target Slices. Starting Load Kernel Modules... [ 10.098638] mmngr: loading out-of-tree module taints kernel. Starting Create[ 10.106155] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000 list of required stce nodes for the current kernel... Mounting Huge Pages File System... Mounting Temporary Directory (/tmp)... Mounting POSIX Message Queue File System... [ OK ] Created slice system-getty.slice. Starting Remount Root and Kernel File Systems... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Mounted Kernel Debug File System. [ 10.243855] PVR_K: 1983: HTBInit: HTBufferSizeInKB = 64 [ OK ] Mounted POSIX Message Queue File Syste[ 10.255075] PVR_K: 1983: RGX Device initialised with BVNC 4.46.6.62 m. [ 10.262807] pvrsrvkm fd000000.gsx: opp[1/4]: (200000000 Hz, 830000 uV) [ 10.269573] pvrsrvkm fd000000.gsx: opp[2/4]: (300000000 Hz, 830000 uV) [ 10.276118] pvrsrvkm fd000000.gsx: opp[3/4]: (400000000 Hz, 830000 uV) [ 10.282653] pvrsrvkm fd000000.gsx: opp[4/4]: (600000000 Hz, 830000 uV) [ 10.289583] [drm] Initialized pvr 1.10.5187610 20170530 for fd000000.gsx on minor 1 [ OK ] Mounted Huge Pages File System. [ 10.302804] imr fe860000.imr0: IMR device (pdev: -1) registered as /dev/video0 [ 10.310362] imr fe870000.imr1: IMR device (pdev: -1) registered as /dev/video1 [ 10.317924] imr fe880000.imr2: IMR device (pdev: -1) registered as /dev/video2 [ 10.325430] imr fe890000.imr3: IMR device (pdev: -1) registered as /dev/video3 [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required stavice nodes for the current kernel. [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... [ OK ] Mounted /var/volatile. [ OK ] Started udev Kernel Device Manager. [ 10.649012] systemd-journald[1981]: Received request to flush runtime journal from PID 1 Starting Load/Save Random Seed... [ 10.675814] random: crng init done [ 10.679219] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Reached target Local File Systems. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Coldplug all Devices. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ 10.887853] lsm9ds0 16-001d: Accelerometer and magnetometer found. [ OK ] Reached target System Initialization. [ 10.900127] lsm9ds0 16-006b: Gyroscope found. [ OK ] Started dnf-automatic-download timer. Starting Network Service... [ OK ] Started dnf makecache timer. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started dnf-automatic-notifyonly timer. [ OK ] Started dnf-automatic-install timer. [ OK ] Reached target Timers. [ OK ] Listening on sshd.socket. [ OK ] Found device /dev/ttySC0. [ 11.314281] wl18xx_driver wl18xx.5.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error 2 [ 11.325003] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2 [ 11.333808] wlcore: WARNING falling back to default config [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Sound Card. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting PowerVR consumer services... Starting Spacenavd startup... [ OK ] Started System Logging Service. [ OK ] Started optee services. [ OK ] Started Kernel Logging Service. Starting Telephony service... [ OK ] Reached target Containers. Starting pvrinit.service... Starting Login [ 11.634642] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) Service... [ 11.646363] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead. [ 11.646363] [ 11.656558] wlcore: WARNING This default nvs file can be removed from the file system [ 11.656558] [ 11.679365] wlcore: loaded [ OK ] Started D-Bus System Message Bus. [ OK ] Started Telephony service. Starting Avahi mDNS/DNS-SD Stack... Starting Save/Restore Sound Card State... [ 11.771686] Bluetooth: Core ver 2.22 [ 11.775433] NET: Registered protocol family 31 [ 11.779910] Bluetooth: HCI device and connection manager initialized [ 11.786334] Bluetooth: HCI socket layer initialized [ 11.791235] Bluetooth: L2CAP socket layer initialized [ 11.796334] Bluetooth: SCO socket layer initialized [ OK ] Started Network Service. [ OK ] Started PowerVR consumer services. [ OK ] Started Spacenavd startup. [ OK ] Started pvrinit.service. [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Login Service. Starting Load/Save RF Kill Switch Status... Starting rc.mm.service... [ OK ] Reached target Network. Starting Network Name Resolution... Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Started rc.mm.service. [ OK ] Started Permit User Sessions. [ OK ] Started Target Communication Framework agent. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttySC0. [ OK ] Reached target Login Prompts. Starting uim-sysfs.service... [ 12.146215] (stk) :sysfs entries created [ OK ] Started Network Name Resolution. [ OK ] Reached target Host and Network Name Lookups. [ 12.359825] (stc): chnl_id list empty :4 [ OK ] Started uim-sysfs.service. Starting pulseaudio.service... Starting Bluetooth service... [ OK ] Started Bluetooth service. [ OK ] Reached target Bluetooth. [ 12.359836] (stk) : st_kim_start [ 12.462783] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.469730] (stk) :ldisc_install = 1 [ 12.471385] Bluetooth: BNEP socket layer initialized Starting Hostname Service... [ 12.622175] (stc): st_tty_open [ OK ] Started Hostname Service. [ 12.622196] (stk) :line discipline installed [ 12.645748] (stk) :ti-connectivity/TIInit_11.8.32.bts [ 12.651763] (stk) :change remote baud rate command in firmware [ OK ] Started pulseaudio.service. [ OK ] Reached target Multi-User System. [ OK ] Started Weston Wayland compositor. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 12.656865] (stk) :skipping the wait event of change remote baud [ 13.997385] audit: type=1006 audit(1580798983.527:2): pid=3659 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=41 Poky (Yocto Project Reference Distro) 2.4.3 h3ulcb ttySC0 h3ulcb login: root Last login: Tue Feb 4 06:49:43 UTC 2020 on tty2 root@h3ulcb:~# uname -a Linux h3ulcb 4.14.75-ltsi-yocto-standard #1 SMP PREEMPT Fri Mar 13 06:23:48 UTC 2020 aarch64 aarch64 aarch64 GNU/Linux root@h3ulcb:~#