< BeagleBoard‎ | GSoC
Revision as of 07:15, 25 March 2020 by Vedant16 (talk | contribs)
Jump to: navigation, search

Proposal for Port am335x_pru_package to remoteproc

Student: Vedant Paranjape
Mentors: Kumar Abhishek, Zubeen Tolani
GSoC: [N/A]


This project is currently just a proposal.


Completed all the requirements listed on the ideas page. the code for the cross-compilation task can be found here submitted through the pull request #138.

About you

IRC: vedant16
School: Veermata Jijabai Technological Institute (VJTI)
Country: India
Primary language : English, Hindi, Marathi
Typical work hours : 10AM - 7PM Indian Standard Time
Previous GSoC participation: I find embedded pretty interesting, given I have experience with ESP32, I think I will be able to excel in this project. This is the first time i am participating in GSoC

About your project

Project name: Port am335x_pru_package to remoteproc


This project will enable the control of the Beaglebone's PRUs using remoteproc and rpmsg driver rather than using uio drivers. The PRU is a dual core micro-controller system present on the AM335x SoC which powers the BeagleBone. It is meant to be used for high speed jitter free IO control. Being independent from the linux scheduler and having direct access to the IO pins of the BeagleBone Black, the PRU is ideal for offloading IO intensive tasks.
The remote processor (RPROC) framework allows the different platforms/architectures to control (power on, load firmware, power off) remote processors while abstracting the hardware differences. In addition it offers services to monitor and debug the remote coprocessor. This eliminates the need of a custom kernel driver for varying range of devices, and in general kernel driver development is a tough task. Using remoteproc vastly increases development efficiency. It also reduces the probability of severe kernel exploits due to elimination of need to write a kernel driver for PRU, rather a Userspace API which is uses sysfs to communicate with RPROC(remoteproc). Even though prussdrv which currently uses uio to handle PRU. RPROC is specially built for the task of handling interprocessor task, it supports full featured interprocessor communications. Thus developing a custom kernel driver for each device is a futile task. Rather we should use an uniform and inbuilt way to access PRU across various BeagleBoards.
How is it better that using uio_pruss?
With a kernel framework like RPROC, it is possible to create firmware defined devices that can be accessed like any other Linux device under /dev.To Linux, this would look no different to /dev/tty0. The Virtio is an extremely powerful concept. RPMSG/RemoteProc is implemented in kernel space and UIO_PRUSS is implemented in userspace. UIO_PRUSS is also a compromise to system security.
If we consider a simplistic example of toggling an LED, It might be easier to implement this in uio_pruss, but when we are dealing with more serious device interface, the infrastructure available with RemoteProc makes the implementation much easier.
Features to be implemented
  1. Updating prussdrv C library to use remoteproc interface rather than the uio interface.
  2. Adding ELF support to PASM, as remoteproc only supports ELF binaries. Provide a option to build using clpru as well.
  3. Port all the existing examples to use remoteproc.
  4. Create a GUI application to control PRU and load firmware into it.

Details of implementation

Updating prussdrv C library to use remoteproc interface rather than the uio interface.
Implement basic functions to control the PRU like start, stop, load binary firmware and load the drivers
  1. modprobe(): Load the pru_rproc module using modprobe
  2. modunprobe(): Unload the pru_rproc module using rmmod
  3. pru_start(): Starts the specified PRU(0/1) by writing "start" to /sys/class/remoteproc/.../state, runs the firmware indicated by, or written to, /sys/class/remoteproc/.../firmware
  4. pru_stop(): Stops the specified PRU(0/1) by writing "stop" to /sys/class/remoteproc/.../state
  5. pru_read_state(): Reports the current state of the specified PRU(0/1) by reading into /sys/class/remoteproc/.../state
  6. pru_load_firmware(): Copies the provided firmware to /sys/class/remoteproc/.../firmware
I intend to implement functions like RESUME, PAUSE using sysfs /sys/kernel/debug/remoteproc/remoteproc.
Adding ELF support to PASM, as remoteproc only supports ELF binaries. Provide a option to build using clpru as well
Port all the existing examples to use remoteproc.
Reimplement stock examples in pru_package repository
  1. PRU_industrialEthernetTimer
  2. PRU_PRUtoPRU_Interrupt
  3. PRU_memAccessPRUDataRa
  4. PRU_memAccess_DDR_PRUsharedRAM
Create a GUI application to control PRU and load firmware into it.
GUI to be implemented.

Command line can be intimidating for beginers and windows users ;)

So, i propose to use a GUI to control the PRU, and load firmware as well remoteproc kernel module. Users comfortable with command line can use the command line utility.
This is implemented using Qt5, I have linked the GUI i intend to use.


Apr 27 Proposal accepted or rejected Community Bonding Period and discussion on the project and resources available.
May 18 Pre-work complete Coding officially begins!
May 25 Milestone #1
  • Introductory YouTube video
  • Setting up PocketBeagle i.e flashing up to date Linux image and Testing user-led blink code :D
  • Running existing example codes from this repository
  • Creating header file for the new userland driver which uses remoteproc
June 1 Milestone #2
June 8 Milestone #3
June 15 18:00 UTC Milestone #4 (Phase 1 evaluations)
June 19 18:00 UTC Phase 1 Evaluation deadline
June 22 Milestone #5
June 29 Milestone #6
July 6 Milestone #7
July 13 18:00 UTC Milestone #8 (Phase 2 evaluations)
July 17 18:00 UTC Phase 2 Evaluation deadline
July 20 Milestone #9
July 27 Milestone #10
August 3 Milestone #11, Completion YouTube video
August 10 - 17 18:00 UTC Final week
August 17 - 24 18:00 UTC End of Session

Experience and approach

I have decent experience in C++, C and Python. I have done several projects involving embedded systems like ESP32, I well-versed with freeRTOS. I recently did a project on ESP32, in which I used ESP to control and plot PID loop running on the embedded device, plotting the values on a python GUI. Other than that I have developed firmware for a 3 DOF arm based on a ESP32 custom board. I did a internship with a embedded deviced startup, where I built:

  1. Built TCP network stack for embedded IoT Devices
  2. Implemented Synchronous TCP server using Boost.Asio(C++) and Boost.Thread(C++)
  3. Implemented a tool to calculate round trip time(RTT) of tcp packets

I actively contribute to open source and do a lot of mini projects throughout the year, you can find my several more interesting projects at my github page


I believe that if I get stuck on my project and my mentor isn’t around, I will use the resources that are available to me. Some of those information portals are listed below.

  2. PRU Guide
  3. Mark Yoder's cookbook is a excellent guide
  4. Derek Molly's beagle bone guide provides all the information needed for getting up and running with my beagle.
  5. The technical reference manuals provided by TI on am3358 and am5729 are the best source
  6. Processor SDK Linux Software Guide is a good reference material
  7. sysfs remoteproc class documentation


If successfully completed, what will its impact be on the community? Include quotes from community members who can be found on and


Please complete the requirements listed on the ideas page. Provide link to pull request.


Is there anything else we should have asked you?