Difference between revisions of "Didj"

From eLinux.org
Jump to: navigation, search
(USB 1.1 HOST Interface)
(Tutorials/How To's)
 
(162 intermediate revisions by 13 users not shown)
Line 1: Line 1:
 +
'''This device is part of the [[LeapFrog_Pollux_Platform | LeapFrog Pollux Platform]], it's recommended to start there for general information.'''
 
[[image:didj.jpg|right|350px|thumb|The LeapFrog Didj]]
 
[[image:didj.jpg|right|350px|thumb|The LeapFrog Didj]]
  
== Project Summary ==
+
== Summary ==
The Didj is a toy produced by Leapfrog marketed for educational games for 5-10 year olds. Although it has a proprietary graphical front end, it runs a generic Linux distribution on an Arm based processor. Soon after the Didj's release, it was discovered that the cartridge port contained pins that allowed for serial console access with root privileges. After this discovery, work began to modify the Didj into an accessible emulation device.
+
The Didj was a toy produced by Leapfrog marketed for educational games for children aged 5-10.  
 +
 
 +
Didj was end-of-lifed by Leapfrog in mid-2010. It has been replaced by the [[Leapster Explorer]].
 +
 
 +
Although Didj has a proprietary graphical front end, it runs a generic Linux distribution on an Arm based processor. Soon after the Didj's release, it was discovered that the cartridge port contained pins that allowed for serial console access with root privileges. After this discovery, work began to modify the Didj into an accessible emulation device.
  
 
Since development began, much has been accomplished, including:
 
Since development began, much has been accomplished, including:
  
* Discovered that the Arm chip is the same as on the GP2X Wiz, only at a lower clock speed.
+
* Discovered that the Arm chip is the same as on the [[GP2X Wiz]], only at a lower clock speed.
 
* Created cartridges that support SD cards
 
* Created cartridges that support SD cards
 
* Accessed the UART features in the cartridge slot
 
* Accessed the UART features in the cartridge slot
  
== Project Goals ==
 
Here is a place to list all the the goals or wants that we have for this project.
 
  
* [http://en.wikipedia.org/wiki/GP2X GP2x] / [http://en.wikipedia.org/wiki/GP2X_Wiz GP2x Wiz]
+
== Platform ==
** Port Libraries
+
[[LeapFrog_Pollux_Platform | LeapFrog Pollux Platform]]
** Flash Player
+
 
** Emulation ([http://www.globalgph.com/m3/sub4.php Wiz Emulators])
+
The Didj is part of 3 different devices that all share a common hardware platform, based around the [[Pollux]] SoC. The platform page contains information generic across these devices, and it is recommended that you refer to that page as it is a good starting point to understanding the Didj, and contains some basic How To's and Tutorials to get you started.
*** NES
 
*** SNES
 
*** Gameboy BW/Color/Advanced
 
*** Gamegear
 
*** MAME
 
*** Atari 2600
 
*** Colecovision
 
*** Others
 
* GUI
 
** Custom or Modified
 
*** Customizable Themes
 
* Homebrew Games
 
* Overclock Processor
 
== Project Status and Issues ==
 
  
* [[Didj_Issues|Project Issues Tracker]]  
+
== Boot Loader ==
 +
* [[Didj_Lightning_Boot| Lightning Boot ]]
 +
* [[Didj_U-Boot| U-Boot ]]
 +
* [[Didj_Emerald_Boot| Compile and Install Emerald-Boot]]
  
 +
== Sources and Toolchains ==
 +
* [[LeapFrog_Pollux_Platform:_Source_Code| Sources and Toolchains]]
  
 
== Tutorials/How To's ==
 
== Tutorials/How To's ==
 +
''' General '''
 +
* [[Didj_Common_Commands|Common Commands Reference]]
 +
* [[LeapFrog_Pollux_Platform:_Console_Access|Console Access]]
 +
* [[LeapFrog_Pollux_Platform:_Cartridge| Cartridges]]
 +
** [[LeapFrog_Pollux_Platform:_Cartridge_Settings| Cartridge Settings]]
 +
* [[LeapFrog_Pollux_Platform:_Extract_Archives| Extract lfp/lf2 Archives]]
 +
''' Networking '''
 +
* [[Didj_Enable_Networking| Enable Networking via USB Gadget]]
 +
* [[Didj_Install_Dropbear| Install Dropbear SSH]]
 +
* [[Didj_MP3_Streaming| Playing MP3 network streams and files]]
 +
* [[LeapFrog_Pollux_Platform:_Networking| Networking Setup]]
 +
* [[LeapFrog_Pollux_Platform:_Networking_Applications| Networking Applications]]
 +
* [[LeapFrog_Pollux_Platform:_Internet_Access| Internet Access from Device]]
 +
* [[LeapFrog_Pollux_Platform:_Mount_NFS_Directory| Mount NFS Directory]]
  
* [[Didj_How_to_Extract_Files|How to extract files from the firmware .exe]]
+
''' USB Storage '''
* [[Didj Serial Console|Adding Serial Console]]
+
* [[Didj_USB_Mounting|USB Mounting Under Windows, Linux, and OS X]]
* Gain access to the Didj as a thumb drive [http://wtfmoogle.com/?page_id=741 from Windows].
+
* [[Didj_SCSI_Commands|SCSI Commands]]
* [[Didj Kernel Build Environment|Creating a Kernel Build Scratchbox]]
 
* [[Didj Build Environment|Setting up a cross compiler build environment and basic usage]]
 
*[[LFConnect_Update_Server_Bypass|LFConnect Update Server Bypass]]
 
*[[Didj_BootLoader_Firmware_Updating|Updating Bootloader/Firmware over USB]]
 
*[[Didj_U_Boot_Flashing_Primer|U-Boot NAND Utilities and Bootloader Update]]
 
*[[Didj_Boot_From_UART|Boot Didj From UART Connection]]
 
*[[Didj_Mount_File_System_Under_Linux|Mount Didj File System Under Linux]]
 
*[[Didj_USB_Mounting|USB Mounting Under Windows, Linux, and OS X]]
 
*[[Didj_Common_Commands|Common Commands Reference]]
 
*[[Didj SD MMC Expansion]]
 
*[[Didj Stop Start Up Junk]] How to remove all the kids game files
 
*[[Didj_Networking_HOWTO| Networking HOWTO - Enabling networking/telnetd (via the USB gadget Ethernet driver) ]]
 
 
 
== Technical Information ==
 
 
 
* [http://sites.google.com/site/claudeschwarz/didjhacking2 Home Brew Cartridge and Custom Bootloader]
 
* [[Didj_Mem_Map|Initial Memory Map Dump]]
 
* [[Didj_GPIO_Map|Map of Didj GPIO Pins]]
 
* The #edev guys (#edev on irc.freenode.net) located [http://www.leapfrog.com/etc/medialib/leapfrog/legal.Par.14642.File.dat/Additional%20Third%20Party%20Notices%20for%20LF%20Connect%20Application%20.pdf THIS] on the leapfrog site.
 
** [http://medialib.leapfrog.com/didj_opensource_code/Didj-Linux-3197-20080429-1631.tar.gz Didj Linux and root filesystem source is here]
 
** busybox isn't listed
 
* The linux kernel source is now available from LeapFrog.
 
[http://medialib.leapfrog.com/didj_opensource_code/Didj-Linux-3197-20080429-1631.tar.gz 2008 version]
 
  
[http://medialib.leapfrog.com/didj_opensource_code/Didj-Linux-4222-20090422-1236.tar.gz 2009 version]
+
''' Cartridge '''
* [[Didj Source Info]]
+
* [[Didj_Make_ATAP| Make an ATAP NAND Cartridge]]
* [http://git.berlios.de/cgi-bin/gitweb.cgi?p=opendidj;a=blob_plain;f=host_tools/lf1000_bootstrap.py;h=f0d3ef0d9186edf368062608ff868914e6083ee4;hb=06890453479d271856f58d1d2cb685ee6e5afd5f LF1000 UART Bootstrap Utility] written in Python
 
* [[media:lf1000-bootstrap-utilities.tar.gz |LF1000 UART Bootstrap Utilities]] based on the OMAP boot utilities from TI
 
  
== Discussion ==
+
''' Flash NAND '''
 +
* [[Didj_U-Boot_NAND_Flashing| Flash Data to NAND]]
 +
* [[Didj_BootLoader_Firmware_Updating|Updating Bootloader/Firmware]]
  
* [http://www.hackerfoundry.com/forums/viewtopic.php?f=4&t=7&sid=4cc66fd2128b96e03603c812ba926301 Didj Project Forum]
+
''' Firmware Image '''
* [irc://chat.freenode.net/didj #Didj on Freenode IRC]
+
* [[File_Systems#Mounting_JFFS2_image_on_PC_using_mtdram| Mount JFFS2 Image on Linux]]
* [http://www.cozybit.com/stories.htm Cozybit boasts of their involvment in integrating Linux with the Didj]
+
** Relevant Settings
* [http://blogs.distant-earth.com/wp/?p=64 Hacking around with the Leapfrog Didj]
+
** Correct endianess
* [http://didjdev.freeforumhost.com/viewforum.php?f=3 Didj Homebrew Forum] (Empty?)
 
* Hackaday Posts
 
** [http://hackaday.com/2010/02/01/leapfrog-didj-handheld-linux-on-the-cheap/ Didj Hacking]
 
** [http://hackaday.com/2010/02/03/leapfrog-didj-followup/ Didj Hacking Followup]
 
  
==Graphics Hardware ==
+
* [[LeapFrog_Pollux_Platform:_Firmware#Didj_JFFS2 | Create JFFS2 image]]
 +
** Relevant Settings
 +
** -e 128
 +
** -p
  
* Resolution: 320x240
+
''' Kernel/RootFS/Firmware'''
 +
* [[Didj_and_Explorer_libSDL|Building libSDL]]
 +
* [[Didj_and_Explorer_SDL_ttf|Building SDL_ttf font library]]
 +
* [[Didj_and_Explorer_SDL_image|Building SDL_image library with jpg and png support]]
 +
* [[Didj_and_Explorer_SDL_mixer|Building SDL_mixer audio library]]
 +
* [[Leapster_Explorer:_tslib_Touchscreen_Library|Building tslib]]
 +
* [[Leapster_Explorer:_SDL_resources|SDL Resources]]
 +
* [[Didj_2.6.31_Kernel| Didj Kernel 2.6.31 Upgrade]]
 +
* [[Didj_Explorer_Kernel|2.6.31 Kernel for Didj]]
 +
* [[Didj_Explorer_SD_Kernel| Boot Kernel and Rootfs from SD w/Framebuffer]]
 +
* [[Leapster_Explorer_Framebuffer_Driver|Linux Framebuffer Driver]]
 +
* [[Didj_and_Explorer_MMC_Patch|Enable SD Card Module]]
 +
* [[Leapster_Explorer_Root_File_System|Building The Explorer Root File System]]
 +
* [[Didj_and_Explorer:_boot_pixel_format|Changing the fb driver to display the boot logo correctly]]
 +
* [[LeapFrog_Pollux_Platform:_TV_Out | TV Out]]
 +
* [[Didj_2.6.31_Generic_Buildroot | Generic Buildroot Rootfs and Kernel build]]
  
* Display Modes: RGBA 565
+
''' Games and Emulators '''
 +
* [[LeapFrog_Pollux_Platform:_Emulators_And_Games| Emulators and Games]]
  
* MLC: Multi-layer controller provides HW compositing for up to three graphics layers
+
''' Brio Development '''
** One 24-bit 2D layers (no HW accel)
+
* [[Didj_Replacement_App_Menu| Replacing the default App Menu from the default App Menu]]
** One 16-bit 3D layer
 
** One YUV video layer (no HW accel)
 
  
* Graphics API OpenGL ES 1.1: A reduced instruction set version of OpenGL for embedded systems. OpenGL is a 3D graphics programming interface. Proprietary interface to Multi- Layer Display controller for 2D RGB and YUV video buffer support. FreeType Font renderer. Theora video codec plays OGG-Theora files.
+
''' JTAG '''
 +
* [[LeapFrog_Pollux_Platform:_JTAG_Pinouts| JTAG Pinouts]]
 +
* [[Pollux:_FTDI_JTAG_How_To| Pollux FTDI JTAG How To]]
 +
* [[Pollux_JTAG_with_Wiggler| Pollux JTAG Wiggler Config]]
 +
* [[LeapFrog_Pollux_Platform:_JTAG_Kernel_Boot| JTAG Kernel Boot]]
  
== Chip List ==
+
''' Compiling Source Code '''
[[Image:Scanned-desoldered-mainboard-front-v2.jpg ‎|350px|thumb|Scan of front side of Didj mainboard, with LF1000 CPU and SDRAM de-soldered]]
+
* [[LeapFrog_Pollux_Platform:_Build_Environment| Set up the Build Environment]]
 +
* [[LeapFrog_Pollux_Platform:_Kernel_Configuration| Kernel Configuration]]
  
[[Image:Scanned-desoldered-mainboard-back-v2a.jpg ‎|350px|thumb|Scan of back side of Didj mainboard, with cartridge socket and NAND de-soldered.]]
+
== Development Scripts and Programs ==
  
[[Image:Didj Mainboard Front.jpg|350px|thumb|A picture of the front of the Didj mainboard]]
+
* [http://git.berlios.de/cgi-bin/gitweb.cgi?p=opendidj;a=blob_plain;f=host_tools/lf1000_bootstrap.py;h=f0d3ef0d9186edf368062608ff868914e6083ee4;hb=06890453479d271856f58d1d2cb685ee6e5afd5f LF1000 UART Bootstrap Utility] written in Python
 +
* [[media:lf1000-bootstrap-utilities.tar.gz |LF1000 UART Bootstrap Utilities]] based on the OMAP boot utilities from TI
  
[[Image:Didj Mainboard Back.jpg|350px|thumb|A picture of the back of the Didj mainboard]]
+
== Technical Information ==
 +
* [[Didj_Mem_Map|Initial Memory Map Dump]]
 +
* [[Didj_GPIO_Map|Map of Didj GPIO Pins]]
 +
* [[LeapFrog_Pollux_Platform:_Technical_Details|Device Comparison]]
  
==== Processor ====
+
''' File System Info '''
* OEM branded version of the MagicEyes [[Pollux]] VF3520F [[media:pollux-datasheet.pdf|Datasheet]]
+
* rootfs / rootfs rw
* Appears to be the 393MHz version of the same processor in the [http://gp2xwiz.com/ GP2x Wiz]
+
* /dev/root / jffs2 ro
* Marked with:
+
* none /proc proc rw
** "LF-1000" - [[LF-1000|LF-1000 Specifications]]
+
* sysfs /sys sysfs rw
** "ARM"
+
* /dev/ram0 /tmp tmpfs rw
** "N12N1D"
+
* /dev/mtdblock1 /flags jffs2 rw,sync,noatime
** "H0815"
+
* /dev/mtdblock2 /mfgdata jffs2 ro,sync,noatime
 +
* /dev/mtdblock10 /Didj vfat rw,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha  rset=iso8859-1
 +
* /dev/mtdblock11 /Cart vfat ro,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha  rset=iso8859-1
  
==== Memory ====
+
Filesystem                Size      Mounted on
* 1 QImonda HYB25DC25616OCE-5 - 32megabyte sdram [[media:HYB25DC25616OCE-5.pdf | Datasheet]]
+
/dev/mtdblock6          14.0M    /
or
+
/dev/mtdblock1          896.0k    /flags
* 1 Nanya NT5DS16M16CS-5T - 32megabyte sdram (Datasheet)
+
/dev/mtdblock2            1.0M    /mfgdata
 +
/dev/mtdblock9          215.8M    /Didj
  
  
* 1 Micron MT29F2G08AAC - 256megabyte nand flash 8-bit [[media:MT29F2G08AAC.pdf | Datasheet]
+
''' Active Kernel/Rootfs
* 1 7s08f -2 input or gate connected to WP on flash
 
==== Audio ====
 
* 1 Cirrus Logic CS43L22 - audio codec [[media:CS43L22.pdf | Datasheet]]
 
  
==== Display Driver ====
+
Near the begging of the boot message you should see one of two root options:
* 1 Giantplus GPM758A0 - 320x240 TFT [http://www.giantplus.com.tw/en/p/34-color_stn_module-gpg0909_3.html Pinouts and Specifications]
+
root=31:04
 +
You are using  mtd4: 00e00000 00020000 "Linux_RFS0" or
 +
root=31:06
 +
You are using  mtd6: 00e00000 00020000 "Linux_RFS1"
  
==== Power ====
 
* 1 Intersil ISL7665SACBAZ - Programmable Over/Under Voltage Detector [[media:isl7665s.pdf | Datasheet]]
 
* 3 TI TPS62050 - Adjustable Step-Down Converter [[media:tps62050.pdf | Datasheet]]
 
  
==== Crystals ====
+
''' Partitions '''
* Oscillators
+
{| cellpadding="4" border="1"
** 12MHz Crystal
+
|-
*** For usb
+
|style="background-color:#CCCCCC"| Name
** 27MHz Crystal
+
|style="background-color:#CCCCCC"| Location
*** For the Processor*
+
|style="background-color:#CCCCCC"| Size
** Barrel Crystal
+
|style="background-color:#CCCCCC"| Device
*** For the RTC 32.768KHz*
+
|style="background-color:#CCCCCC"| Notes
 +
|-
 +
| LF1000_uniboot
 +
| 0x00000000
 +
| 0x00020000
 +
| /dev/mtd0
 +
| Lightning Boot
 +
|-
 +
| Atomic_Boot_Flags
 +
| 0x00020000
 +
| 0x000E0000
 +
| /dev/mtd1
 +
| On NAND
 +
|-
 +
| Manufacturing_Data
 +
| 0x00100000
 +
| 0x00100000
 +
| /dev/mtd2
 +
| On NAND
 +
|-
 +
| Kernel0
 +
| 0x00200000
 +
| 0x00200000
 +
| /dev/mtd3
 +
| On NAND
 +
|-
 +
| Linux_RFS0
 +
| 0x00400000
 +
| 0x00E00000
 +
| /dev/mtd4
 +
| On NAND
 +
|-
 +
| Kernel1
 +
| 0x01200000
 +
| 0x00200000
 +
| /dev/mtd5
 +
| On NAND
 +
|-
 +
| Linux_RFS1
 +
| 0x01400000
 +
| 0x00E00000
 +
| /dev/mtd6
 +
| On NAND
 +
|-
 +
| Brio
 +
| 0x02200000
 +
| 0x0DE00000
 +
| /dev/mtd7
 +
| On NAND
 +
|-
 +
| EXT
 +
| 0x10000000
 +
| 0x10000000
 +
| /dev/mtd8
 +
|
 +
|-
 +
| Cartridge
 +
| 0x00000000
 +
| 0x10000000
 +
|
 +
| On Cartridge NAND
 +
|}
  
==== Test Pads ====
 
<gallery widths=200px>
 
Image:JTAG PADS.jpg|JTAG Test Pads
 
</gallery>
 
  
* JTAG on pads
+
''' Battery Compartments '''
** TP8 - Vcc
 
** TP9
 
** TP10
 
** TP11
 
** TP12
 
** TP13
 
** TP14 - Vss
 
  
==== Ethernet? ====
+
The Didj has two identical battery compartments, the combined collection of batteries are wired in series.
There is info of a CS9800 Ethernet controller used on the development board
+
* Battery Compartment Terminals:
 +
** Term 1 - Battery +
 +
** Term 2 - Temp Sensor +  Wired to Pollux pins K20 / GPIOA 28 and K21 / GPIOA 29
 +
** Term 3 - Temp Sensor -
 +
** Term 4 - Battery -
  
<nowiki>* See the processor datasheet page 20.</nowiki>
 
  
= USB =
+
''' Rechargeable Batteries '''
  
=== USB 2.0 Device Interface ===
+
In addition to the terminals facing the Didj's contacts, there are another set of contacts facing away from the Didj.
*Pins USB_DP and USB_DM on the Processor
+
These contacts are duplicates used by the charging station.  The batteries themselves are NIMH cells, producing around 2.5v per pack when fully charged.
*The Usb 2.0 Device port is what is used on the Didj to connect to the PC.
 
  
=== USB 1.1 HOST Interface ===
 
*Pins UP and UM on the Processor
 
*The USB1.1 Host pins must be pulled down through 15Kohm resistor whether it is used or not.
 
*There is no traces to the USB Host pins thus we can not use USB Host
 
<gallery widths=200px>
 
Image:USB_Host_pads.jpg|USB Host Pads
 
</gallery>
 
  
= Cartridges =
+
''' Recharging Station '''
[[Didj_Cart_Info|Detailed Pin info of the Cart Connector]]
 
== Original Cartridge ==
 
Manufactured by Sandisk
 
* s740878-1
 
* 4620329
 
* 0621
 
* 151-10043-07-a
 
<gallery widths=200px>
 
Image:cartfront.jpg|Original Cartridge Front
 
Image:cartback.jpg|Original Cartridge Back
 
</gallery>
 
[[Category:Hardware]]
 
  
== Custom Cartridges ==
+
The recharger station contains a battery charge circuit with temperature monitoring.  The station also has a pair of contacts that duplicate the 9V dc barrel jack.
  
=== Home Etched Didj Breakout Board ===
 
  
* Easy to make at home (can be made with a radioshack kit and a dremel)
+
''' SSP / SPI Controller '''
* The board layout was designed in eagle.
+
[[Didj SPI Info]]
** The Eagle Board file [[media:dijibreakoutboard.zip|Download]]
 
** The Didj Edgecard connector library file [[media:LEAPFROG_DIJI_EDGECARD.zip|Download]]
 
*** You can use this to make any board you want.
 
** Edited Didj Cartridge library [http://alternet.us.com/other/LEAPFROG_DIdj.zip Download]
 
*** (including outlines and keepout regions according to Awesomnesser's diagrams)
 
* This cartridge locks in just like the real thing.
 
** It is easy to do just superglue a small piece of FR4 in the corner and dremel a notch out. (see dimensions below)
 
** You will also need a spacer on the top and bottom and those dimensions are also included.
 
  
<gallery widths=200px>
+
== Images ==
Image:Awesomenesser01.jpg|The breakout board
+
<gallery perrow=5 caption="PCB Images">
Image:Awesomenesser02.jpg|The bottom of the board
+
File:Scanned-desoldered-mainboard-front-v2.jpg|Front side mainboard, with LF1000 CPU and SDRAM de-soldered.
Image:Awesomenesser03.jpg|The breakout board clicked into the Didj
+
File:Bga-closeup.jpg|Close up of the LF1000 CPU ball-grid.
Image:Awesomenesser04.jpg|The board hooked up to a sd card and FTDI cable (same as Claudes board)
+
File:Scanned-desoldered-mainboard-back-v2a.jpg|Back side mainboard, with cartridge socket and NAND de-soldered.
Image:Awesomenesser05.jpg|The dimensions of the basic cartridge
+
File:Didj Mainboard Front.jpg|Front side mainboard
Image:Awesomenesser06.jpg|The laser printout for the toner transfer (Remember to mirror your printout and turn off the unused layers)
+
File:Didj Mainboard Back.jpg|Back side mainboard
 
</gallery>
 
</gallery>
  
=== Hack an Original Cart ===
+
== External Links ==
 
+
* [http://www.cozybit.com/stories.htm Cozybit boasts of their involvment in integrating Linux with the Didj]
* Modify an original cart to have a uart output
+
* [http://blogs.distant-earth.com/wp/?p=64 Hacking around with the Leapfrog Didj]
<gallery widths=200px>
+
* [http://sites.google.com/site/claudeschwarz/didjhacking2 Claude's Didj Hacking Page]
Image:hacked.jpg|Modified original cartridge
+
* Hackaday Posts
</gallery>
+
** [http://hackaday.com/2010/02/01/leapfrog-didj-handheld-linux-on-the-cheap/ Didj Hacking]
 
+
** [http://hackaday.com/2010/02/03/leapfrog-didj-followup/ Didj Hacking Followup]
=== Claudes Cartridge ===
 
* Features
 
** Jumpers (For custom bootloader)
 
** SD Card (Enabled through the custom bootloader)
 
** USB through a FTDI chip
 
** Optional NAND
 
* [http://sites.google.com/site/claudeschwarz/didjhacking2 Claudes Website]
 
* [[media:ClaudesSchematic.pdf | Claudes Schematic]]
 
* [[media:ClaudesGerberFiles.zip | Claudes Gerber Files]]
 
<gallery widths=200px>
 
Image:claudesboardrendered.jpg|Rendering
 
Image:claudesboardpopulated.jpg|Populated Cartridge
 
</gallery>
 
 
 
=== SD and USB Serial Cart ===
 
 
 
* Features
 
** Fits (mostly) within the Didj
 
** Includes an FTDI FT232RL USB-Serial adaptor for Bootloader and Serial Console
 
** Includes SD card slot
 
** Includes solder jumpers for custom bootloader
 
** Open Eagle source files (CC Attribution, Non-Commercial, Share Alike)
 
* [http://alternet.us.com/other/SD_UART-2.pdf Front and Back PDF]
 
* [http://alternet.us.com/other/SD_UART-2.zip Eagle files]
 
* [http://batchpcb.com/index.php/Products/27971 BatchPCB public design]
 
* Comments welcome!
 
** Gerbers haven't been made yet.  Please post comments here, or as a message to me.
 
** I think the design is correct based on Claude's schematic and Awesomenesser's diagrams, but I can't be sure.
 
** Later, I'll have this produced by BatchPCB, I'll post a link to the public design on that site, if others want boards made.
 
 
 
= File System Info =
 
 
 
*rootfs / rootfs rw
 
 
 
*/dev/root / jffs2 ro
 
 
 
*none /proc proc rw
 
 
 
*sysfs /sys sysfs rw
 
 
 
*/dev/ram0 /tmp tmpfs rw
 
 
 
*/dev/mtdblock1 /flags jffs2 rw,sync,noatime
 
 
 
*/dev/mtdblock2 /mfgdata jffs2 ro,sync,noatime
 
 
 
*/dev/mtdblock10 /Didj vfat rw,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha  rset=iso8859-1
 
 
 
*/dev/mtdblock11 /Cart vfat ro,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha  rset=iso8859-1
 
 
 
Filesystem                Size      Mounted on
 
 
 
/dev/mtdblock6          14.0M    /
 
 
 
/dev/mtdblock1          896.0k    /flags
 
 
 
/dev/mtdblock2            1.0M    /mfgdata
 
  
/dev/mtdblock9          215.8M    /Didj
 
  
  
== Important File Locations ==
+
[[Category:Didj]]
 +
[[Category:LeapFrog Pollux Platform]]

Latest revision as of 00:08, 26 February 2013

This device is part of the LeapFrog Pollux Platform, it's recommended to start there for general information.

The LeapFrog Didj

Summary

The Didj was a toy produced by Leapfrog marketed for educational games for children aged 5-10.

Didj was end-of-lifed by Leapfrog in mid-2010. It has been replaced by the Leapster Explorer.

Although Didj has a proprietary graphical front end, it runs a generic Linux distribution on an Arm based processor. Soon after the Didj's release, it was discovered that the cartridge port contained pins that allowed for serial console access with root privileges. After this discovery, work began to modify the Didj into an accessible emulation device.

Since development began, much has been accomplished, including:

  • Discovered that the Arm chip is the same as on the GP2X Wiz, only at a lower clock speed.
  • Created cartridges that support SD cards
  • Accessed the UART features in the cartridge slot


Platform

LeapFrog Pollux Platform

The Didj is part of 3 different devices that all share a common hardware platform, based around the Pollux SoC. The platform page contains information generic across these devices, and it is recommended that you refer to that page as it is a good starting point to understanding the Didj, and contains some basic How To's and Tutorials to get you started.

Boot Loader

Sources and Toolchains

Tutorials/How To's

General

Networking

USB Storage

Cartridge

Flash NAND

Firmware Image

Kernel/RootFS/Firmware

Games and Emulators

Brio Development

JTAG

Compiling Source Code

Development Scripts and Programs

Technical Information

File System Info

  • rootfs / rootfs rw
  • /dev/root / jffs2 ro
  • none /proc proc rw
  • sysfs /sys sysfs rw
  • /dev/ram0 /tmp tmpfs rw
  • /dev/mtdblock1 /flags jffs2 rw,sync,noatime
  • /dev/mtdblock2 /mfgdata jffs2 ro,sync,noatime
  • /dev/mtdblock10 /Didj vfat rw,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha rset=iso8859-1
  • /dev/mtdblock11 /Cart vfat ro,noatime,fmask=0022,dmask=0022,codepage=cp437,iocha rset=iso8859-1
Filesystem                Size       Mounted on
/dev/mtdblock6           14.0M     /
/dev/mtdblock1          896.0k    /flags
/dev/mtdblock2            1.0M    /mfgdata
/dev/mtdblock9          215.8M    /Didj


Active Kernel/Rootfs

Near the begging of the boot message you should see one of two root options:

root=31:04 

You are using mtd4: 00e00000 00020000 "Linux_RFS0" or

root=31:06 

You are using mtd6: 00e00000 00020000 "Linux_RFS1"


Partitions

Name Location Size Device Notes
LF1000_uniboot 0x00000000 0x00020000 /dev/mtd0 Lightning Boot
Atomic_Boot_Flags 0x00020000 0x000E0000 /dev/mtd1 On NAND
Manufacturing_Data 0x00100000 0x00100000 /dev/mtd2 On NAND
Kernel0 0x00200000 0x00200000 /dev/mtd3 On NAND
Linux_RFS0 0x00400000 0x00E00000 /dev/mtd4 On NAND
Kernel1 0x01200000 0x00200000 /dev/mtd5 On NAND
Linux_RFS1 0x01400000 0x00E00000 /dev/mtd6 On NAND
Brio 0x02200000 0x0DE00000 /dev/mtd7 On NAND
EXT 0x10000000 0x10000000 /dev/mtd8
Cartridge 0x00000000 0x10000000 On Cartridge NAND


Battery Compartments

The Didj has two identical battery compartments, the combined collection of batteries are wired in series.

  • Battery Compartment Terminals:
    • Term 1 - Battery +
    • Term 2 - Temp Sensor + Wired to Pollux pins K20 / GPIOA 28 and K21 / GPIOA 29
    • Term 3 - Temp Sensor -
    • Term 4 - Battery -


Rechargeable Batteries

In addition to the terminals facing the Didj's contacts, there are another set of contacts facing away from the Didj. These contacts are duplicates used by the charging station. The batteries themselves are NIMH cells, producing around 2.5v per pack when fully charged.


Recharging Station

The recharger station contains a battery charge circuit with temperature monitoring. The station also has a pair of contacts that duplicate the 9V dc barrel jack.


SSP / SPI Controller Didj SPI Info

Images

External Links