EBC Exercise 10a Analog In

From eLinux.org
Revision as of 13:09, 28 July 2020 by Yoder (talk | contribs) (Analog in - Continuous: Added 200KHz sample rate)
Jump to: navigation, search

thumb‎ Embedded Linux Class by Mark A. Yoder

The Beagle has seven exposed analog inputs, numbered AIN0 to AIN6, on the P9 header. They are accessed through the Linux Industrial IO (iio) system (https://wiki.analog.com/software/linux/docs/iio/iio). They can be read either a sample at a time (One Shot) or in blocks of samples (Continous). One shot can be used to read the setting of a potentiometer, or an analog temperature sensor. The continuous mode is for reading a microphone or some other analog signal. With the proper configuration, the continuous input can read 12 bit samples at 200k samples/second.

Here's is how to use each.

Analog in - One Shot

(This is based on BeagleBone Black Analog Input.)

The bone has eight Analog Inputs; seven are exposed on P9, labeled AIN in table 11 below.


The AIN pins are sampled at 12 bits and 8k samples per second by default. The input voltage is between 0 and 1.8V. Fortunately, both analog ground (0V) and 1.8V are available on P9.

The photo below shows a small potentiometer wired to the bone. One end goes to the analog ground (pin 34), the other analog 1.8V (pin 32). The wiper is attached to AIN5 which is pin 36.

Bone gpio.JPG BoneGPIO.png

You interact with the analog in much like the gpio, but it appears in a different place.

bone$ cd /sys/bus/iio/devices/iio:device0
bone$ ls -F
buffer/          in_voltage2_raw  in_voltage6_raw  power/
dev              in_voltage3_raw  in_voltage7_raw  scan_elements/
in_voltage0_raw  in_voltage4_raw  name             subsystem@
in_voltage1_raw  in_voltage5_raw  of_node@         uevent

There are the various analog inputs, in_voltage6_raw corresponds with AIN6

bone$ cat in_voltage6_raw

Change the pot and rerun cat. What's the min and max value you get? Is it 12 bits?

Analog in - Continuous

(This is based on information at: http://software-dl.ti.com/processor-sdk-linux/esd/docs/latest/linux/Foundational_Components/Kernel/Kernel_Drivers/ADC.html#Continuous%20Mode)

Reading a continuous analog signal requires some set up. First go to the iio devices directory.

bone$ cd /sys/bus/iio/devices/iio:device0
bone$ ls -F
buffer/  in_voltage0_raw  in_voltage2_raw  in_voltage4_raw  in_voltage6_raw  name      power/          subsystem@
dev      in_voltage1_raw  in_voltage3_raw  in_voltage5_raw  in_voltage7_raw  of_node@  scan_elements/  uevent

Here you see the files used to read the one shot values. Look in scan_elements to see how to enable continuous input.

bone$ ls scan_elements
in_voltage0_en     in_voltage1_index  in_voltage2_type   in_voltage4_en     in_voltage5_index  in_voltage6_type
in_voltage0_index  in_voltage1_type   in_voltage3_en     in_voltage4_index  in_voltage5_type   in_voltage7_en
in_voltage0_type   in_voltage2_en     in_voltage3_index  in_voltage4_type   in_voltage6_en     in_voltage7_index
in_voltage1_en     in_voltage2_index  in_voltage3_type   in_voltage5_en     in_voltage6_index  in_voltage7_type

Here you see three values for each analog input, _en (enable), _index (index of this channel in the buffer’s chunks) and _type (How the ADC stores its data). (See the link above for details.)

Let's use the input at P9.40 which is AIN1. To enable this input:

bone$ echo 1 > scan_elements/in_voltage1_en

Next set the buffer size.

bone$ ls buffer
data_available  enable  length  watermark

Let's use a 512 sample buffer. You might need to experiment with this.

bone$ echo 512 > buffer/length

Then start it running.

bone$ echo 1 > buffer/enable

Now, just read from /dev/iio:device0.

1KHz sine wave sampled at 8KHz

An example Python program that does the above and the reads and plot the buffer is here: analogInContinuous.py Run it:

bone$ cd /var/lib/cloud9/BeagleBone/Black
bone$ ./analogInContinuous.py
Hit ^C to stop

Here's the output of a 1KHz sine wave.

Analog in - Continuous, Change the sample rate

The built in ADCs sample at 8k samples/second by default. They can run as fast as 200k samples/second by editing a device tree.

bone$ cd /opt/source/bb.org-overlays
bone$ make

This will take a while the first time as it compiles all the device trees.

bone$ vi src/arm/src/arm/BB-ADC-00A0.dts

Around line 54 you'll see

ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;

The first line says for every sample returned, average 16 values. This will give you a cleaner signal, but if you want to go fast, change the 16's to 1's. The second line says to delay 0x98 cycles between each sample. Set this to 0 to got as fast a possible.

ti,chan-step-avg = <1 1 1 1 1 1 1 1>;
ti,chan-step-opendelay = <0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00>;

Now compile it.

10KHz triangle wave sampled at 200KHz
bone$ make
  DTC     src/arm/BB-ADC-00A0.dtbo
gcc -o config-pin ./tools/pmunts_muntsos/config-pin.c

It knows to only recompile the file you just edited. Now install and reboot.

bone$ sudo make install
'src/arm/AM335X-PRU-UIO-00A0.dtbo' -> '/lib/firmware/AM335X-PRU-UIO-00A0.dtbo'
'src/arm/BB-ADC-00A0.dtbo' -> '/lib/firmware/BB-ADC-00A0.dtbo'
'src/arm/BB-BBBMINI-00A0.dtbo' -> '/lib/firmware/BB-BBBMINI-00A0.dtbo'
bone$ reboot

A number of files get installed, including the ADC file. Now try rerunning.

bone$ cd /var/lib/cloud9/BeagleBone/Black
bone$ ./analogInContinuous.py
Hit ^C to stop

Here's the output of a 10KHz sine wave.

thumb‎ Embedded Linux Class by Mark A. Yoder