ECE497 Beagle Bone WiFi
Embedded Linux Class by Mark A. Yoder
This wiki is for anyone trying to use a WiFi adapter on the Beagle Bone. It is originally created by Michael Junge, EE senior at Rose-Hulman Institute of Technology, class of 2012. As new information is discovered please feel free to edit this wiki.
You will need a WiFi adapter from Adafruit. (I had to buy mine, however as the class expands Dr. Yoder pay potentially have a few to hand out for experimentation.)
You will also need the A6 hardware version of the BeagleBone. This does not work with the A5 version. (again at a later date this may not be an issue)
You will finally need the A5 software version of Angstrom found from EBC Exercise 03 Installing a Beagle OS. Again make sure it is the A5 software, this does not work with the A6 Rev.
Finally you will need a 5V BeagleBone power supply. The power supply that comes with the Beagle XM Board is suffient as well.
Required Package Updates
When installing packages do not have the WiFi adapter plugged in.
beagle$ opkg update beagle$ opkg install linux-firmware-rtl8192cu bealge$ opkg install wireless-tools
Procedure for running WiFi
You must follow this procedure for enabling the WiFi.
1) Plug in the WiFi adapter (do not plug in an Ethernet cable, it may not work properly)
2) Plug in the usb and connect the BeagleBone to your laptop.
3) Plug in the power adapter for the BeagleBone
4) Connect to the BeagleBone either through screen command or the LAN set up by the usb (for connecting through screen or LAN refer to: EBC Exercise 02 Out-of-the-Box, Bone)
5) Run these lines of code:
beagle$ ifconfig wlan0 to see what wlan0 currently displays beagle$ iwconfig wlan0 to see if wlan0 is configured properly beagle$ iwconfig wlan0 essid x x-your own personal ID beagle$ iwconfig wlan0 password y y- your own personal password beagle$ iwconfig wlan0 to check if your essid and password are correct beagle$ ifconfig wlan0 up to enable wlan0 beagle$ ifconfig wlan0 xxx.xxx.x.x set to your own private network, usually 192.168.1,x beagle$ ping xxx.xxx.x.1 to check if your wireless is working correctly beagle$ ping google.com to check DNS and Ethernet, because of campus security I have not been able to access DNS
Here is my personal screenshot of being connected to my wireless router as noted by wlan0 instead of eth0. The BeagleBone code is in the white box. My laptop is in red. This screenshot shows WiFi works, however it can be a pain to set up.
Ad-Hoc Networks are useful for creating a link between two wifi enabled devices without going through an access point (or through Rose-Hulman's internet). Make sure that your wifi dongle supports Ad-Hoc mode (ibss mode) before purchasing. In order to work properly, Ad-Hoc mode must be set up on both the Beagle and the Host computer (thus taking up the wifi module of the host computer, unless a second wifi dongle is used). There instructions will guide you through the process of setting up both sides.
Beagle Bone Ad-Hoc Network
The basic idea on the Bone side is to set the wireless device to Ad-Hoc mode and then configure the network by giving it a name, password (if desired), setting the frequency, etc. Full details of the iwconfig command can be found [here]. We then have to give the network an IP address in order to use it.
beagle$ iwconfig ra0 mode ad-hoc sets the device (ra0 in our case, could be wlan0 or some other device) to ad-hoc mode beagle$ iwconfig ra0 essid "<ESSID NAME>" sets the device SSID to the given SSID name (make sure to include quotes around the name) beagle$ ifconfig ra0 192.168.1.1 netmask 255.255.255.0 sets the IP address for the network (can be anything you want) beagle$ ifconfig ra0 up brings the network up in case it wasn't (usually it has to be up in order for the above changes to work)
In the future, these settings should be saved to /etc/rc.local, but we haven't set that up yet so the instructions aren't posted here.
If all has gone correctly, you should be able to use the ifconfig command to see:
beagle$ ra0 Link encap:Ethernet HWaddr 00:0C:43:00:15:3A inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:51016 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11735546 (11.1 MiB) TX bytes:105576 (103.1 KiB)
Check to see if all the settings are the same as what you set them to.
Host Ad-Hoc Network
The Ad-Hoc network must be set up on the host in addition to the Beaglebone. Note that these settings are not permenant.
host$ iw wlan0 set type ibss set our wireless card to Ad-Hoc (ibss) mode host$ ip link ls list available networks (the SSID of the network we just created above should be visible now) host$ iw wlan0 ibss join <ESSID NAME> <FREQ> join the SSID at the given frequency (if the frequency is 2.412 GHz put 2412 [MHz] in for FREQ) host$ ip addr add 192.168.1.3/24 dev wlan0 assign the host a different IP address on the same general network (change the last digit of the IP address you created above) host$ ssh email@example.com ssh into the Beaglebone's IP host$ ... host$ iw wlan0 ibss leave leave the Ad-Hoc network
I have not been able to figure out how to connect to the campus network. I know it has to deal with wpa supplicant. However at this time, I have not done enough research into wpa supplicant to connect successfully.
Embedded Linux Class by Mark A. Yoder