Difference between revisions of "ECE497 Project Electric Car"
m (Moved to ECE497Fall2013)
|Line 1:||Line 1:|
Latest revision as of 04:41, 14 October 2014
Embedded Linux Class by Mark A. Yoder
I'm using the following template to grade. Each slot is 10 points. 0 = Missing, 5=OK, 10=Wow!
07 Executive Summary - Not up to date 09 Packaging - Nice sequence of photos documenting the assembly. Show where car came from. 09 Installation Instructions - Good 09 User Instructions - Good 09 Highlights - Nice video, but add audio to tell what's happening. 08 Theory of Operation - Some more details would be nice. 09 Work Breakdown - Also report the time spent building the car 09 Future Work - Good 09 Conclusions - OK 10 Demo 00 Late Comments: I'm looking forward to seeing this. Score: 88/100
This project interfaces the Beaglebone with motor-based electronic mini-car. The gpio pins are used to control the motor on the car to remote it. Some additional interfaces, such as a IR sensor to control the moving direction of the car, and an analog input to control the speed of the car, are considered to be done based on the progress of the project.
Currently we have the small car which can be controlled by keyboard, or IR sensor. With the keyboard controlling, the car can go foreword and backward, make a turn to both right and left. With the IR sensor controlling, the car can keep space before the barrier in front of item.
At first, we use the H-bridge to control four motors which connect to four wheels for the car. And use the GPIO pins to control this H-bridge. And then use a analog input pin to get the signal feedback from the IR sensor.
Depending on the time, in the feature time, there are lots of works can be done for this robot car. (This isn't up to date)
|Robot Car Kits (Give link)||1|
|sharp 2d120x f IR sensor||1|
|L293 H-Bridge Chip||1|
|100 ohm Resistors||2|
Soldering the L293 H-bridge chip, rsistors, and diodes together. And put the control board on the car.
Connect the motor to the control board.
Glue the IR Sensor in front of the car.
Connect both on/off switch and IR sensor to the beaglebone.
wire eveything to the beaglebone.
Our Electric Robot Car is ready to go.
The Github Link for this project is https://github.com/weizhen1883/Electric-Car.git.
- connect the H-bridge signal pin to P9_11(LeftFront) P9_12(LeftBack) P9_13(RightFront) P9_14(RightnBack)
- connect the IR sensor signal to P9_35 AIN6
- connect both H-bridge and IR sensor power to sys_5V and GND
- power the beaglebone
- run make to get ECar and GoForwordwithSensor files
- run ./ECar to work with keyboard controlling
- run ./GoForwordwithSensor to work with IR Sensor controlling
- Login to the Beaglebone and open the project folder.
- $beagle ./ECar to run the keyboard control model.
- $beagle ./GoForwordwithSensor to run the IR sensor control model.
At the keyboard control model
- 'w'----go forward
- 'x'----go backward
- 'a'----turn left
- 'd'----turn right
At this time, this Electric Car can only controlled by keyboard, and run forward and backward to keep the space between item and the barrier in front of item.
Theory of Operation
The major tasks in your project is to make the car can sensing the distance in the front, and when the distance is too small it will go backward, when it is too big, it will go forward. If the distance is just within the range, the car will stop.
For this project, in the future there are lots of works can be done.
- First, to add the battery package, to make the robot work without cable connected.
- Second, add more IR sensors to make it can run and make the turn and also go pass the barriers.
- Third, it should be possible to add the GPS sensor to sensing the location, and make the robot go around our campus.
For this project, we just do a very sample demo with beaglebone, we can do a lot of things in the future. Anyway, at this time, we make the car run by beaglebone controlling. We get our milestone.
Embedded Linux Class by Mark A. Yoder