Flyswatter2 RouterStationPro Windows How To

From eLinux.org
Revision as of 19:41, 17 April 2012 by Wmat (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

This guide will walk you through connecting the Flyswatter2 and the Ubiquiti RouterStation Pro to your Windows PC, and installing and running OpenOCD. This guide was tested with Windows XP and Windows 7. Instructions are identical on 32-bit and 64-bit versions of Windows unless otherwise noted.


Connecting the Flyswatter2 and the RouterStation Pro

To hook up the Flyswatter2 and the RouterStation Pro, you will need:

  • Flyswatter2
    • 20-pin ARM to 14-pin MIPS JTAG Adapter Board
    • USB Male A/Male B Cable
    • 14-pin JTAG Ribbon Cable
  • RouterStationPro
    • RS-232 Serial Cable with two female connectors
    • CAT6 Cable
    • Power Over Ethernet Injector (with power cable)


The items listed under RouterStationPro are included with the MIPS Linux Starter Kit.

Connect the MIPS JTAG Adapter Board to the Flyswatter2.

Fs2 mips adapter.png

The 14-pin end of the adapter board should face up toward the top of the board, as in the picture.


Connect the 14-pin ribbon cable to the Adapter Board.

Fs2 mips jtag.png

The ribbon cable should have a notch on the connector to force it into the correct position. If it doesn't, make sure to align Pin 1 as shown in the image to the left. (Pin 1 is on the side of the cable with the red stripe.)


Connect the Other End of the Ribbon Cable to the RouterStation Pro.

Fs2 rspro jtag.png

Again, be sure to align the red stripe with Pin 1, as shown in the picture. Pin 1 is toward the outer edge of the board. It is also marked on the bottom of the RouterStation Pro.


Connect the RS-232 Serial Cable.

Fs2 rspro bothcables.png

Connect the cable as shown in the picture.


Connect the USB Cable to the Flyswatter2.

Fs2 rspro usb.png

Connect the Male B adapter to the Flyswatter 3. (The Male B end is the squarish end, not the flat end.)


Connect the CAT6 Cable to the Power Over Ethernet Injector.

Poe cat6.png

Leave the boards alone for now. Find the Power Over Ethernet Injector in the MIPS Linux Starter Kit, and connect the CAT6 cable. The PoE injector has two ethernet ports, but only one supplies power. Be sure to use the correct one. The correct ethernet port is labeled.


Connect the Power Adapter to the Power Over Ethernet Injector.

Poe power.png

Connect the power cable to the other side of the PoE injector.


Connect the Other End of the CAT6 Cable to the RouterStation Pro.

Rspro poe.png

Connect the CAT6 cable to the RouterStation Pro's Power Over Ethernet port. Warning: The RouterStation Pro has three ethernet ports in addition to the PoE port. Connecting the PoE injector to one of the regular ethernet ports may damage the board. The PoE port is the closest to the center of the board, to the right of the three ethernet ports as shown in the picture. It is labeled POE on the board.


Plug the Power Adapter into a Wall Outlet.

The green LEDs on the RouterStation Pro should briefly flash, and the leftmost LED should remain on.

Plug the USB Cable into your PC.

The green power LED on the Flyswatter2 should come on and remain on.


Installing OpenOCD

OpenOCD (Open On-Chip Debugger) is open-source software that interfaces with the Flyswatter2. OpenOCD provides debugging and in-system programming for embedded target devices. You will need to compile OpenOCD from source, and patch the source with one of the OpenOCD Patches for Flyswatter 3 support.

Whichever guide you use, be sure to install the patch! All four guides include instructions on downloading and installing the patch.

Windows 7

Use Windows 7 guides if compiling for Windows Vista.

Compiling OpenOCD Win7

Compiling OpenOCD Win7 D2XX


Windows XP

Compiling OpenOCD WinXP

Compiling OpenOCD WinXP D2XX


The first set of instructions uses libFTDI, an open-source driver library for FTDI devices. The second set uses FTD2XX, a closed-source driver library from Future Technology Devices International.


Running OpenOCD

Now you are ready to run OpenOCD. Open a command line window; if you're not sure how to do this, see Running OpenOCD on Windows. Navigate to the folder containing openocd.exe (the openocd-bin folder you created in the compile guide) and type:

cd C:\openocd-bin
openocd -f interface/flyswatter2.cfg -c "jtag_khz 15000" -f target/ar71xx.cfg

When you start OpenOCD you should see something like this:

Rspro ocdstartup win.png

Telnet Connection

You cannot enter commands directly to OpenOCD. Open a new command window and type:

telnet localhost 4444

You will should see this prompt:

Telnet win.png

You can give commands to OpenOCD through this prompt. If you don't see the prompt on Windows 7, you may need to enable the Telnet client. See Configuring Windows 7 for OpenOCD.


Common OpenOCD Commands

To see a full list of OpenOCD commands, enter help in the telnet window.

reset

Resets the Flyswatter2. The output of the Reset command should look like this:

Rspro reset win.png

halt

Sends a halt request to the Flyswatter2. If the Flyswatter2 halts, you will see text output in the telnet window. (If the Flyswatter2 is already halted, you will see no output.)

Rspro halt win.png

halt [timeout]

You can also use halt followed by a time in milliseconds. OpenOCD waits for the target to halt the specified amount of time, then gives up if the target has not halted. You can use this to avoid OpenOCD hanging because the Flyswatter2 fails to halt. For example, to send a halt command with a timeout of one second, type:

halt 1000

resume

Enter resume to end a halt. You will not see any text output in the telnet window.

reg

Displays a numbered list of all of the Flyswatter2's registers.

Rspro reg win.png

If the board is not halted, the board registers will be displayed but not their values.

reg [entry]

Run reg with a register number to display the contents of a register, in hexadecimal. The register number corresponds to the output of the reg command with no arguments, above. You must run the halt command before reading registers.

Rspro reg0 win.png

If you run reg while the Flyswatter2 is not halted, you will still see the value stored in the register. However, registers change contents very quickly while the device is running; by the time you see the value, the value actually in the register may be different. If you try to run reg while the device is not halted, you will see this:

Rspro reg0nothalted win.png

Note that the RouterStation Pro does not show any warning if you run the reg command while the board is running.


reg [entry] [value]

Sets the value of a register. The register number corresponds to the output of the reg command with no arguments, above. Make sure the Flyswatter2 is halted (with the halt command) before you change the value of a register!

You can enter registry values in either decimal, by typing a number by itself, or in hexadecimal, by prefacing the value with 0x.

Rspro regset win.png


GDB Debugger

GDB, the GNU Project Debugger is a debugging tool provided with the GNU Compiler Collection (GCC). GDB allows you to stop and start a running program, examine its functioning, and make changes. To install and use GDB with OpenOCD, follow the instructions on the Windows GDB Debugger page below.

Windows GDB Debugger

The GDB debugger page will walk you through installing GDB for use with OpenOCD, and loading and testing a simple program.