Difference between revisions of "IMX 6 Internal and drivers pin-muxing reference"
(Created page with "{| class="wikitable" |- ! A17!! NANDF_CS2 !! CCM_CLKO2 !! CLK_OUPUT !! USB_CLK !! Clock a 24mhz x l'hub usb2514 |- | F15 || NANDF_CS0 || ExampleR1C3 || GPIO6_IO11 || output, H...") |
|||
Line 3: | Line 3: | ||
! A17!! NANDF_CS2 !! CCM_CLKO2 !! CLK_OUPUT !! USB_CLK !! Clock a 24mhz x l'hub usb2514 | ! A17!! NANDF_CS2 !! CCM_CLKO2 !! CLK_OUPUT !! USB_CLK !! Clock a 24mhz x l'hub usb2514 | ||
|- | |- | ||
− | | F15 || NANDF_CS0 | + | | F15 || NANDF_CS0 || GPIO6_IO11 || output, HIGH level || EN_VTT || It turns off the Vtt when it goes in suspend mode, active high |
|- | |- | ||
| B18 || NANDF_D5 || GPIO2_IO05 || OUTPUT, open drain level (high) || SDIO_PWR || It enables the supply voltage of the sdcard, active high | | B18 || NANDF_D5 || GPIO2_IO05 || OUTPUT, open drain level (high) || SDIO_PWR || It enables the supply voltage of the sdcard, active high |
Revision as of 08:01, 13 January 2015
A17 | NANDF_CS2 | CCM_CLKO2 | CLK_OUPUT | USB_CLK | Clock a 24mhz x l'hub usb2514 |
---|---|---|---|---|---|
F15 | NANDF_CS0 | GPIO6_IO11 | output, HIGH level | EN_VTT | It turns off the Vtt when it goes in suspend mode, active high |
B18 | NANDF_D5 | GPIO2_IO05 | OUTPUT, open drain level (high) | SDIO_PWR | It enables the supply voltage of the sdcard, active high |
D19 | SD4_DAT7 | GPIO2_IO15 | OUTPUT, open drain level (low) | SELUSB_HOST_nDEV | USB selection of SAM3X8E in host or client mode , 0=host |
D19 | CSI0_DAT19 | GPIO6_IO05 | OUTPUT, low level | CAM_RST | Reset for the CSI camera module |
P24 | DISP0_DAT0 | GPIO4_IO21 | INPUT (piloted by driver) | ERASE | Cancellation of the SAM3X8E device before a reprogram, level 1 actives the cancellation, then it should be put in open drain |
M6 | CSIO_DAT18 | GPIO6_IO04 | OUTPUT, low level | CAM_EN | Enabling the CSI camera module, active high |
P1 | CSIO_PIXCLK | GPIO5_IO18 | INPUT | DTR_ARD | Monitoring the Arduino serial protocol to recognize erase and reset commands |
L3 | CSIO_DAT17 | GPIO6_IO03 | INPUT | RTS_ARD | Monitoring the Arduino serial protocol to recognize erase and reset commands |
A19 | NANDF_D4 | GPIO2_IO04 | OUTPUT, low level | EN_5V | It turns off the TENSION of 5VDC for the times it goes in suspend mode, active high |
G25 | EIM_A19 | GPIO2_IO19 | OUTPUT, open drain (low) | WP_SPI_FLASH | Logical level 1 = not protected 0= flash protected against scripts |