Difference between revisions of "IMX 6 Internal and drivers pin-muxing reference"

From eLinux.org
Jump to: navigation, search
Line 18: Line 18:
 
| T5 || GPIO_0 || GPIO1_IO00 || gpio0 || INPUT KERNEL DRIVEN || IMX6_PIC_RST || SAM3X8E reset, active low
 
| T5 || GPIO_0 || GPIO1_IO00 || gpio0 || INPUT KERNEL DRIVEN || IMX6_PIC_RST || SAM3X8E reset, active low
 
|-
 
|-
| P24 || DISP0_DAT0 || GPIO4_IO21 || gpio117 || INPUT KERNEL DRIVEN || ERASE || Cancellation of the SAM3X8E device before a reprogram, level 1 activates the cancellation, then it should be put in open drain  
+
| P24 || DISP0_DAT0 || GPIO4_IO21 || gpio117 || INPUT KERNEL DRIVEN || ERASE || Cancellation of the SAM3X8E device before a reprogram, level 1 enables the cancellation, then it should be put in open drain  
 
|-
 
|-
| T1 || GPIO_2 || GPIO1_IO02 || gpio2 || OUTPUT HIGH, KERNEL DRIVEN || PANEL_ON || It enables the power supply of the LVDS panel, attivo alto
+
| T1 || GPIO_2 || GPIO1_IO02 || gpio2 || OUTPUT HIGH, KERNEL DRIVEN || PANEL_ON || It enables the power supply of the LVDS panel, active high
 
|-
 
|-
 
| R6 || GPIO_4 || GPIO1_IO04 || gpio4 || OUTPUT HIGH, KERNEL DRIVEN || BL_ON || It enables the backlight of the LVDS panel, active high
 
| R6 || GPIO_4 || GPIO1_IO04 || gpio4 || OUTPUT HIGH, KERNEL DRIVEN || BL_ON || It enables the backlight of the LVDS panel, active high
 
|-
 
|-
| M25 || EIM_WAIT || GPIO5_IO00 || gpio128 || OUTPUT HIGH || USB_OTG_SEL is 0 || It enables the USB_OTG port on the miniUSB connector, at 1 it connects it at SAM3X8E for host-client communication
+
| M25 || EIM_WAIT || GPIO5_IO00 || gpio128 || OUTPUT HIGH || USB_OTG_SEL is 0 || It enables the USB_OTG port on the mini-USB connector, at 1 it connects it at SAM3X8E for host-client communication
 
|-
 
|-
| R2 || GPIO_16 || GPIO7_IO11 || gpio203 || OUTPUT LOW || VBUS_EN || It enables and disables the vbus for the SAM3X8E , 1 enables, 0 disables (used in ADK mode)
+
| R2 || GPIO_16 || GPIO7_IO11 || gpio203 || OUTPUT LOW || VBUS_EN || It enables and disables the vbus for the SAM3X8E, 1 enables, 0 disables (used in ADK mode)
 
|-
 
|-
 
| R1 || GPIO_17 || GPIO7_IO12 || gpio204 || OUTPUT HIGH || HUB_USB_RST# || Reset signal for the hub usb2514, active low
 
| R1 || GPIO_17 || GPIO7_IO12 || gpio204 || OUTPUT HIGH || HUB_USB_RST# || Reset signal for the hub usb2514, active low
Line 32: Line 32:
 
| A17 || NANDF_CS2 || CCM_CLKO2 || || CLK_OUTPUT || USB_CLK || Clock at 24MHz for the hub usb2514
 
| A17 || NANDF_CS2 || CCM_CLKO2 || || CLK_OUTPUT || USB_CLK || Clock at 24MHz for the hub usb2514
 
|-
 
|-
| F15 || NANDF_CS0 || GPIO6_IO11 || gpio171 || OUTPUT HIGH || EN_VTT || It turns off the Vtt when it goes in suspend mode, active high  
+
| F15 || NANDF_CS0 || GPIO6_IO11 || gpio171 || OUTPUT HIGH || EN_VTT || It turns off the Vtt at power off, active high  
 
|-
 
|-
| B18 || NANDF_D5 || GPIO2_IO05 || gpio37 || OUTPUT HIGH || SDIO_PWR || It enables the supply voltage of the sdcard, active high  
+
| B18 || NANDF_D5 || GPIO2_IO05 || gpio37 || OUTPUT HIGH || SDIO_PWR || It enables the supply voltage of the sd-card, active high  
 
|-
 
|-
 
| D19 || SD4_DAT7 || GPIO2_IO15 || gpio47 || OUTPUT LOW || SELUSB_HOST_nDEV || USB selection of SAM3X8E in host or client mode , 0=host
 
| D19 || SD4_DAT7 || GPIO2_IO15 || gpio47 || OUTPUT LOW || SELUSB_HOST_nDEV || USB selection of SAM3X8E in host or client mode , 0=host
Line 46: Line 46:
 
| L3 || CSIO_DAT17 || GPIO6_IO03 || gpio163 || INPUT || RTS_ARD || Monitoring the Arduino serial protocol to recognize erase and reset commands
 
| L3 || CSIO_DAT17 || GPIO6_IO03 || gpio163 || INPUT || RTS_ARD || Monitoring the Arduino serial protocol to recognize erase and reset commands
 
|-
 
|-
| A19 || NANDF_D4 || GPIO2_IO04 || gpio36 || OUTPUT LOW || EN_5V || It turns off the tension of 5VDC for the times it goes in suspend mode, active high
+
| A19 || NANDF_D4 || GPIO2_IO04 || gpio36 || OUTPUT LOW || EN_5V || It turns off the tension of 5VDC at power off, active high
 
|}
 
|}

Revision as of 08:23, 13 January 2015

iMX6_pin iMX6_pad_name used function exported gpio n° default at boot Schematics Label How to use it
A22 SD2_DAT0 GPIO1_IO15 gpio15 OUTPUT LOW touch_rst touch controller reset, active low
A23 SD2_DAT2 GPIO1_IO13 gpio13 INPUT touch_int touch controller interrupt, it should generate interrupt at touch
E22 EIM_EB2 GPIO2_IO30 gpio62 OUTPUT KERNEL DRIVEN aud_rst# AUDIO CODEC RST, ATTIVO BASSO
F23 EIM_EB3 GPIO2_IO31 gpio63 OUTPUT HIGH en_eth_pwr Ethernet PHI power for consumption and power management
C13 SD3_DAT5 GPIO7_IO00 gpio192 INPUT sdio_cd Microsd card detect
W5 KEY_COL0 TXD4 OUTPUT KERNEL DRIVEN U1ARX_IMX Used to communicate with and program SAM3X8E, it should be programmed as output only if used and if sel_dbg_uart is 0, otherwise it should be left open drain
V6 KEY_ROW0 RXD4 INPUT U1ATX_IMX Used to communicate with and program SAM3X8E
T5 GPIO_0 GPIO1_IO00 gpio0 INPUT KERNEL DRIVEN IMX6_PIC_RST SAM3X8E reset, active low
P24 DISP0_DAT0 GPIO4_IO21 gpio117 INPUT KERNEL DRIVEN ERASE Cancellation of the SAM3X8E device before a reprogram, level 1 enables the cancellation, then it should be put in open drain
T1 GPIO_2 GPIO1_IO02 gpio2 OUTPUT HIGH, KERNEL DRIVEN PANEL_ON It enables the power supply of the LVDS panel, active high
R6 GPIO_4 GPIO1_IO04 gpio4 OUTPUT HIGH, KERNEL DRIVEN BL_ON It enables the backlight of the LVDS panel, active high
M25 EIM_WAIT GPIO5_IO00 gpio128 OUTPUT HIGH USB_OTG_SEL is 0 It enables the USB_OTG port on the mini-USB connector, at 1 it connects it at SAM3X8E for host-client communication
R2 GPIO_16 GPIO7_IO11 gpio203 OUTPUT LOW VBUS_EN It enables and disables the vbus for the SAM3X8E, 1 enables, 0 disables (used in ADK mode)
R1 GPIO_17 GPIO7_IO12 gpio204 OUTPUT HIGH HUB_USB_RST# Reset signal for the hub usb2514, active low
A17 NANDF_CS2 CCM_CLKO2 CLK_OUTPUT USB_CLK Clock at 24MHz for the hub usb2514
F15 NANDF_CS0 GPIO6_IO11 gpio171 OUTPUT HIGH EN_VTT It turns off the Vtt at power off, active high
B18 NANDF_D5 GPIO2_IO05 gpio37 OUTPUT HIGH SDIO_PWR It enables the supply voltage of the sd-card, active high
D19 SD4_DAT7 GPIO2_IO15 gpio47 OUTPUT LOW SELUSB_HOST_nDEV USB selection of SAM3X8E in host or client mode , 0=host
D19 CSI0_DAT19 GPIO6_IO05 gpio65 OUTPUT LOW KERNEL DRIVEN CAM_RST Reset for the CSI camera module
M6 CSIO_DAT18 GPIO6_IO04 gpio164 OUTPUT LOW KERNEL DRIVEN CAM_EN Enabling the CSI camera module, active high
P1 CSIO_PIXCLK GPIO5_IO18 gpio146 INPUT DTR_ARD Monitoring the Arduino serial protocol to recognize erase and reset commands
L3 CSIO_DAT17 GPIO6_IO03 gpio163 INPUT RTS_ARD Monitoring the Arduino serial protocol to recognize erase and reset commands
A19 NANDF_D4 GPIO2_IO04 gpio36 OUTPUT LOW EN_5V It turns off the tension of 5VDC at power off, active high