Difference between revisions of "L4T Jetson/r32.3.x patch"

From eLinux.org
Jump to: navigation, search
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
'''Multimedia'''
+
This page has moved to: https://elinux.org/Jetson/L4T/r32.3.x_patches
[GSTREAMER]streaming using jpegenc halts after a short delay
 
https://forums.developer.nvidia.com/t/streaming-using-jpegenc-halts-after-a-short-delay/109924/5
 
 
 
[GSTREAMER]Control-rate property(VBR/CBR) takes no effect
 
https://forums.developer.nvidia.com/t/how-to-use-h-264-5-control-rate-with-gstreamer/119052/7
 
 
 
[MMAPI]setQpRange error
 
https://forums.developer.nvidia.com/t/setqprange-error/110464/7
 
 
 
'''Misc'''
 
[Nano/TX1] fix the Nano and TX1 APP partition cloning issue
 
https://devtalk.nvidia.com/default/topic/1064479/jetson-nano/about-the-making-of-the-mirror-of-the-jetson-nano-module/post/5419408/#5419408
 
 
 
[Nano A02(sdcard)] fix the dtb update failed.
 
Modify the file at ../Linux_for_tegra/rootfs/opt/nvidia/l4t-bootloader-config/nv-l4t-bootloader-config.sh as below and reflash or just copy it to Tegra and update the DTB again.
 
diff --git a/rfs/opt/nvidia/l4t-bootloader-config/nv-l4t-bootloader-config.sh b/rfs/opt/nvidia/l4t-bootloader-config/nv-l4t-bootloader-config.sh
 
index 921efc2..e383176 100755
 
--- a/rfs/opt/nvidia/l4t-bootloader-config/nv-l4t-bootloader-config.sh
 
+++ b/rfs/opt/nvidia/l4t-bootloader-config/nv-l4t-bootloader-config.sh
 
@@ -1,5 +1,5 @@
 
  #!/bin/bash
 
-# Copyright (c) 2019, NVIDIA CORPORATION.  All rights reserved.
 
+# Copyright (c) 2019-2020, NVIDIA CORPORATION.  All rights reserved.
 
  #
 
  # NVIDIA CORPORATION and its licensors retain all intellectual property
 
  # and proprietary rights in and to this software, related documentation
 
@@ -123,10 +123,10 @@ t210ref_update_qspi_check () {
 
                        # need to update QSPI
 
                        return 0
 
                elif (( "${sys_maj_rev}" == "${qspi_maj_rev}" )); then
 
-                      if (( "${sys_min_rev}" >= "${qspi_min_rev}" )); then
 
+                      if (( "${sys_min_rev}" > "${qspi_min_rev}" )); then
 
                                # sys_rel == qspi_rel
 
                                # sys_maj_rev == qspi_maj_rev
 
-                              # sys_min_rev >= qspi_min_rev
 
+                              # sys_min_rev > qspi_min_rev
 
                                # need to update QSPI
 
                                return 0
 
                        else
 
 
 
 
 
 
 
 
 
'''USB'''
 
[TX2]Not enough host controller resources for new device state
 
https://forums.developer.nvidia.com/t/xbox-360-controller-through-usb-hub-broken-in-jetpack-4-x-works-in-jetpack-3-x-not-enough-host-c/110621/2
 
 
 
[Jetson Nano]Power control
 
https://forums.developer.nvidia.com/t/usb-power-control/79037/7
 
 
 
[Jetson Nano]Do USB2 compliance test on USB hub
 
https://forums.developer.nvidia.com/t/jetson-nano-usb2-0-tuning-guide-bus-error-core-dumped/113139/4
 
 
 
'''Camera'''
 
Segmentation fault when running nvarguscamerasrc pipeline
 
TX1/Nano
 
https://devtalk.nvidia.com/default/topic/1070455/jetson-nano/bug-nvarguscamerasrc-segmentation-fault/post/5429630/#5429630
 
TX2/Xavier
 
https://devtalk.nvidia.com/default/topic/1062196/jetson-tx2/nvargus-daemon-freeze-hang-on-pipeline-stop-on-r32-1/post/5429629/#5429629
 
 
Add preferred stride cid control for stride adjustment. (v4l2-ctl --set-ctrl preferred_stride=256 preferred_stride=256)
 
https://devtalk.nvidia.com/default/topic/1073152/jetson-tx2/video-for-linux-v4l-issue-for-onboard-ov5693/post/5436809/#5436809
 
 
 
'''SPI'''
 
TX1/Nano enable the SPI interface. Need modify the u-boot to remove the GPIO enable bit and modify the dts for the pinmux configure.
 
https://forums.developer.nvidia.com/t/check-pinmux-on-spi0-1-on-jetson-nano/115534/20?u=shaneccc
 

Latest revision as of 19:01, 17 June 2020