Difference between revisions of "R-Car/Boards/H3SK"

From eLinux.org
Jump to: navigation, search
m (→‎Introduction: Remove type name)
(→‎In case of DDR 8GiB board)
Line 374: Line 374:
 
SW1=OFF
 
SW1=OFF
 
  ws1.0: SW6[all]=OFF
 
  ws1.0: SW6[all]=OFF
−
  ws1.1/ws2.0: SW6[1]=ON, SW6[2]=ON, SW6[3]=OFF, SW6[4]=ON
+
  ws1.1/ws2.0/ws3.0: SW6[1]=ON, SW6[2]=ON, SW6[3]=OFF, SW6[4]=ON
 
JP1 -> 1-2 short
 
JP1 -> 1-2 short
 
</pre>
 
</pre>
Line 390: Line 390:
 
  ws1.0: SW6[3]=ON
 
  ws1.0: SW6[3]=ON
 
  ws1.1: SW6[1]=OFF, SW6[3]=ON
 
  ws1.1: SW6[1]=OFF, SW6[3]=ON
−
  ws2.0: SW6[3]=ON
+
  ws2.0/ws3.0: SW6[3]=ON
 
</pre>  
 
</pre>  
 
<li> Flash bootparam_sa0.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
 
<li> Flash bootparam_sa0.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:

Revision as of 16:55, 7 July 2020

Software for Starter Kit
Software for Kingfisher
Software for CCPF-SK
Boards
Packages
Q&A / FAQ
Partner solution search
(External link)
Solutions


Introduction

This is the Wiki for the Renesas R-Car Starter Kit Premier board. Refer to the R-Car page for information about Renesas' R-Car SoC family.

Topic

EOL Notification of the M3SK

Production of M3SK is discontinued.
See M3SK page for detail.

The new version of R-Car Starter Kit Premier is now on sale !!

  • Equipped with R-Car H3e-2G
    (En) https://www.renesas.com/jp/en/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
    (Zh) https://www.renesas.com/jp/zh/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
    (Jp) https://www.renesas.com/jp/ja/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
  • CPU performance is increased 20% by supporting up to 2GHz frequency over past products.
  • You can buy from here.

SW Release Information

Board name SW name Release date Note
R-Car Starter Kit ( Premier / Pro ) Yocto v5.9.0 (stable) [New!!] 2022/02/08
Kingfisher Infotainment Board Yocto v5.9.0 (stable) [New!!] 2022/02/14 To check for latest information, please refer to the meta-rcar/tree/v5.9.0.
Android 10 (stable) 2021/07/26 R-Car Starter Kit Premier(R-Car H3) + Kingfisher is supported.
R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) + Kingfisher is also supported from 2021/11/25.
Android P (stable) 2020/09/29 R-Car Starter Kit Premier(R-Car H3) + Kingfisher is supported.
R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) + Kingfisher is also supported from 2021/03/16.
CCPF-SK Board Yocto v5.9.0 (stable) [New!!] 2022/02/08 Prebuilt binary is available in Quick startup guide page. (Updated on 2022/03/18)


Hardware

H3SK has several kinds of boards

  • H3 WS1.1 silicon mounted board 
    Type name: RTP0RC7795SKBX0010SA00
  • H3 WS2.0 silicon mounted board 
    Type name: RTP0RC77951SKBX010SA00[S/N 2001~3000] (LPDDR4: DDR 4GiB(Samsung 1GB x4), eMMC 8GB(Samsung))
Type name: RTP0RC77951SKBX010SA00[S/N 3001~3300] (LPDDR4: DDR 4GiB(Samsung 1GB x4), eMMC 64GB(SanDisk))
Type name: RTP0RC77951SKBX010SA01[S/N 4001-4500] (LPDDR4: DDR 4GiB(Micron 1GB x4), eMMC 8GB(Micron))
Type name: RTP0RC77951SKBX010SA03[S/N 20001-20200] (LPDDR4: DDR 8GiB(Samsung 2GB x4), eMMC 32GB(Samsung))
Type name: RTP0RC77951SKBX010SA03[S/N 20201-20400] (LPDDR4: DDR 8GiB(Samsung 2GB x4), eMMC 32GB(SanDisk))
  • H3 WS3.0 silicon mounted board 
    Type name: RTP0RC77951SKBX010SA03[S/N 25051- ] (LPDDR4: DDR 8GiB(Samsung 2GB x4), eMMC 128GB(Samsung))
    H3 SK variation
    Type Name Serial Number SoC version DDR eMMC Protection circuit threshold
    RTP0RC77951SKBX010SA00 2001-3000 2.0 4GiB(Samsung 1GB x4) 8GB(Samsung) none
    RTP0RC77951SKBX010SA00 3001-3300 2.0 4GiB(Samsung 1GB x4) 64GB(SanDisk) 5.15 volt
    RTP0RC77951SKBX010SA01 4001-4500 2.0 4GiB(Micron 1GB x4) 8GB(Micron) none
    RTP0RC77951SKBX010SA03 20001-20200 2.0 8GiB(Samsung 2GB x4) 32GB(Samsung) none
    RTP0RC77951SKBX010SA03 20201-20400 2.0 8GiB(Samsung 2GB x4) 32GB(SanDisk) 6.0 volt
    RTP0RC77951SKBX010SA03 25051- 3.0 8GiB(Samsung 2GB x4) 128GB(Samsung) 6.0 volt

    Top view
    Bottom view

    Hardware Features

    • R-CAR H3
      • ARM CA57 (ARMv8) 1.5 GHz quad core, with NEON/VFPv4, L1$ I/D 48K/32K, L2$ 2MB
      • ARM CA53 (ARMv8) 1.2 GHz quad core, with NEON/VFPv4, L1$ I/D 32K/32K, L2$ 512K
      • Memory controller for LPDDR4-3200 4GB in 2 channels, each 64-bit wide
      • Two- and three-dimensional graphics engines,
      • Video processing units,
      • 3 channels Display Output,
      • 6 channels Video Input,
      • SD card host interface,
      • USB3.0 and USB2.0 interfaces,
      • CAN interfaces
      • Ethernet AVB
      • PCI Express Interfaces
    • Memories
      • INTERNAL 384KB SYSTEM RAM
      • DDR 4 GB LPDDR4
      • HYPERFLASH 64 MB HYPER FLASH (512 MBITS, 160 MHZ, 320 MBYTES/S)
      • QSPI FLASH 16MB QSPI (128 MBITS,80 MHZ,80 MBYTES/S)1 HEADER QSPI MODULE
      • EMMC 8 GB EMMC (HS400 240 MBYTES/S)
      • MICROSD-CARD SLOT (SDR104 100 MBYTES/S)
    • Connectors
      • CN1 COM Express type connector 440pin
      • CN2 QSPI Flash module
      • CN3 DEBUG JTAG
      • CN4 HDMI
      • CN5 USB 2.0
      • CN6 Push-Pull microSD Card Socket
      • CN7 Ethernet, Connector, RJ45
      • CN8 LINE Out
      • CN9 MIC Input
      • CN10 DEBUG SERIAL (not populated)
      • CN11 CPLD Programming JTAG
      • CN12 DEBUG SERIAL (serial)
      • CN13 Main Power Supply input (5VDC)
      • CN14 CPU Fan
    • Switches
      • SW1 Hyper Flash
      • SW2 Software Readable DIPSWITCHES (4x)
      • SW3 Software Readable Push button
      • SW4 Software Readable Push button
      • SW5 Software Readable Push button
      • SW6 Mode Settings
      • SW7 CPLD Reset
      • SW8 Power
      • SW9 Reset
    • Board specifications
      • Dimensions: 95mm × 95mm
      • Board thickness: 1.6mm
      • External power supply 5V / 6A max, Ripple & Noise (Vp-p) Full load 200mV
      • T opr Operating ambient temperature 0°C to 40°C Do not expose to condensation
      • Vcc 5V system power supply voltage (range 5V +- 5%)
      • I board Maximum current consumption 8A , 40W

    New H3SK

    Where to buy

    R-Car Starter Kit Premier(H3 v3.0) board(RTP0RC77951SKBX010SA03) can be ordered from following distributors:

    Click to buy R-Car Starter Kit Premier board from SHIMAFUJI ELECTRIC INCORPORATED - World wide - < Available >
    Click to buy R-Car Starter Kit Premier board) from Marutsu-elec - Japan Only < Not available >


    R-Car H3 SoC Documentation

    Official board documentation

    Kingfisher (R-Car Starter Kit extension board)

    Instruction of using H3SK with the Kingfisher board located here http://elinux.org/R-Car/Boards/Kingfisher

    Quick Start How To

    This sections describes steps that are necessary to run a "Hello, World!" application using Yocto build. Both X11 and Wayland are supported.

    Build Yocto image

    Refer to Yocto for steps necessary for making a Yocto image.

    Connect 5 V power supply to the board

    Use 5 V power supply with a 5.5 mm barrel plug. The power supply should be able to provide 4(Min) ~ 8(Max)Amps.

    Note

    • The recommended value is 8 Amps. But, user can use 4 Amps. and 6 Amps. (depends on the use case).

    Connect to serial console

    Use a microUSB cable to connect the PC to R-Car Starter Kit Premier (H3ULCB) board. CN12 ("CPLD/DEBUG") must be used on Starter Kit side. It is routed to SCIF2 in the R-Car H3 via a FT232 interface converter chip.

    On Linux, FT232 driver is included with kernel versions >=2.6.12. Windows driver and sources can be found on FTDI Chip website.

    Serial settings are 115200 8N1. Any standard terminal emulator program can be used.

    On Linux:

    picocom 

    sudo picocom -b 115200 DEVICE

    replace DEVICE with the proper tty device name, for example /dev/ttyUSB0. Running dmesg | tail can help locating proper device. After the successful connection, picocom should display: 

    picocom v1.7
    
port is        : /dev/ttyUSB0
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv
imap is        : 
omap is        : 
emap is        : crcrlf,delbs, 
    
Terminal ready

    Use Ctrl+A, Ctrl+Q to exit picocom.

    minicom 

    sudo minicom -b 115200 -D DEVICE

    replace DEVICE with the proper tty device name, for example /dev/ttyUSB0. Running dmesg | tail can help locating proper device. After the successful connection, minicom should display: 

    Welcome to minicom 2.6.2
    
OPTIONS: I18n 
Compiled on Aug  7 2013, 13:32:48.
Port /dev/ttyUSB0
    
Press CTRL-A Z for help on special keys

    Use Ctrl+A, Q to exit minicom.

    Power on the board and go to U-Boot prompt

    Short-press SW8 "Power" to switch the board on. Then you should see the following output in the terminal: 

    Welcome to minicom 2.7
    
OPTIONS: I18n 
Compiled on Jan  1 2014, 17:13:19.
Port /dev/ttyUSB0, 18:31:48
    
Press CTRL-A Z for help on special keys
                                                                                                                                                                                                                 
NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.9                                                           
NOTICE:  BL2: PRR is R-Car H3 ES1.1                                                                                       
NOTICE:  BL2: Boot device is HyperFlash(80MHz)                                                                            
NOTICE:  BL2: LCM state is CM
NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x52
NOTICE:  BL2: DDR1600(rev.0.10)
NOTICE:  BL2: DRAM Split is 4ch
NOTICE:  BL2: QoS is default setting(rev.0.32)
NOTICE:  BL2: Lossy Decomp areas
NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
NOTICE:  BL2: v1.1(release):3ad02ac
NOTICE:  BL2: Built : 13:03:52, Sep 20 2016
NOTICE:  BL2: Normal boot
NOTICE:  BL2: dst=0xe631a208 src=0x8180000 len=512(0x200)
NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
    
U-Boot 2015.04 (Sep 23 2016 - 18:54:42)
    
CPU: Renesas Electronics R8A7795 rev 1.1
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot:  3

    Quickly hit any key to get into U-boot command prompt. Use SW9 ("Reset") to reboot the board when necessary.
    You should see the following: 

    Hit any key to stop autoboot:  0                                                                                                            
=>

    Change/update MAC address for Ethernet interface

    In U-boot command line type: 

    => setenv ethact ravb
=> setenv ethaddr aa:bb:cc:dd:ee:ff
=> saveenv

    The original (board default) MAC address can be found on the label on top of RJ45 connector.

    A user who purchased H3SK board must set the above by himself.

    Configure U-Boot to boot over TFTP + NFS or from a micro SD card

    Refer to Yocto page for steps necessary for running Yocto.

    Serial Console

    Use a micro-USB cable to connect to "Debug Serial-0" (CN10 for ws1.0, CN12 for ws1.1/ws2.0). Serial settings are 115200 8N1.

    Booting Linux

     * Kernel config: defconfig
 * Kernel image: arch/arm64/boot/Image
 * DTB (ws2.0): arch/arm64/boot/dts/renesas/r8a77951-ulcb.dtb
 * DTB (ws1.0/ws1.1): arch/arm64/boot/dts/renesas/r8a77950-ulcb.dtb

    U-Boot boot command: 

    tftpboot 0x48080000 Image
tftpboot 0x48000000 r8a77951-ulcb.dtb or r8a77950-ulcb.dtb
booti 0x48080000 - 0x48000000

    NOTE: ws2.0 silicon is supported Yocto v2.19 or later. NOTE: RTP0RC77951SKBX010SA03(DDR 8GiB) is supported Yocto v3.13.0 or later.

    Kernel v5.5 and older used different DTB names: 

     * DTB (ws2.0): arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb
 * DTB (ws1.0/ws1.1): arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb
 * DTB (RTP0RC77951SKBX010SA03(DDR 8GiB)): arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-4x2g.dtb

    Flashing firmware

    In case of DDR 4GiB board

    RTP0RC77951SKBX010SA00
RTP0RC77951SKBX010SA01
    Writing data (Yocto v2.23, v3.4, v3.6, v3.7, v3.9 and v3.13 or later)
    Filename Program Top Address Flash Save Address Description
    bootparam_sa0.srec 0xE6320000 0x000000 Loader(Boot parameter)
    bl2-h3ulcb.srec 0xE6304000 0x040000 Loader
    cert_header_sa6.srec 0xE6320000 0x180000 Loader(Certification)
    bl31-h3ulcb.srec 0x44000000 0x1C0000 ARM Trusted Firmware
    tee-h3ulcb.srec 0x44100000 0x200000 OP-Tee
    [Yocto v2.23, v3.4, v3.6, v3.7 and v3.9] u-boot-elf.srec 0x50000000 0x640000 U-Boot
    [Yocto v3.13 or later] u-boot-elf-h3ulcb.srec 0x50000000 0x640000 U-Boot


    In case of DDR 8GiB board

    RTP0RC77951SKBX010SA03
    Writing data (Yocto v3.13.0 or later)
    Filename Program Top Address Flash Save Address Description
    bootparam_sa0-4x2g.srec 0xE6320000 0x000000 Loader(Boot parameter)
    bl2-h3ulcb-4x2g.srec 0xE6304000 0x040000 Loader
    cert_header_sa6-4x2g.srec 0xE6320000 0x180000 Loader(Certification)
    bl31-h3ulcb-4x2g.srec 0x44000000 0x1C0000 ARM Trusted Firmware
    tee-h3ulcb.srec 0x44100000 0x200000 OP-Tee
    u-boot-elf-h3ulcb-4x2g.srec 0x50000000 0x640000 U-Boot
    1. Power off the board 
      2. Press SW8
    2. Set SW and JP as follows: 
      3. SW1=OFF
 ws1.0: SW6[all]=OFF
 ws1.1/ws2.0/ws3.0: SW6[1]=ON, SW6[2]=ON, SW6[3]=OFF, SW6[4]=ON
JP1 -> 1-2 short
    3. Power on the board 
      4. Press SW8
Minimonitor starts and provides prompts on console
    4. Change SW as follows: 
      5. SW1=ON
 ws1.0: SW6[3]=ON
 ws1.1: SW6[1]=OFF, SW6[3]=ON
 ws2.0/ws3.0: SW6[3]=ON
    5. Flash bootparam_sa0.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      6. 3
y
e6320000
0
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bootparam_sa0.srec", after upload finished press any key
y
    6. Flash bl2-h3ulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      7. 3
y
e6304000 (e6302000 if using Yocto BSP versions v2.12 and v2.16)
40000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl2-h3ulcb.srec", after upload finished press any key
y
    7. Flash cert_header_sa6.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      8. 3
y
e6320000
180000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "cert_header_sa6.srec", after upload finished press any key
y
    8. Flash bl31-h3ulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      9. 3
y
44000000
1C0000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl31-h3ulcb.srec", after upload finished press any key
y
    9. Flash tee-h3ulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      10. 3
y
44100000
200000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "tee-h3ulcb.srec", after upload finished press any key
y
    10. Flash u-boot-elf.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
      11. 3
y
50000000 (49000000 if using Yocto BSP version v2.12)
640000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "u-boot-elf.srec", after upload finished press any key
y
    11. Reset the board 
      12. Press SW9


    Test procedures

    Known Issues

  • Some H3 v2.0 SK(RTP0RC77951SKBX010SA00) have been confirmed to freeze the system (Ex. Yocto v2.23.1, v3.4.0, v3.6.0 and v3.7.0).
    If it stops please update to Yocto v3.9.0 or later.
  • The following H3 Starter Kit boards have PCIe 1ch disabled.
    Serial Number: 3001-3300
Serial Number: 20201-20400

    [Note] Please check the Serial Number carefully on your board.

    How to enable:

    • If you don't use PCIe 1ch, ignore this "Known Issue".
    • PCIe 1ch is connected to ComEx(CN1) of H3 Starter Kit.
    1. Connect WinPC and H3 Starter Kit board(CN12) with a USB cable
    3. [H3 SK] Power on
    5. [WinPC] Run the exe(*) file
    7. [WinPC] Select "OK"
    9. [WinPC] If you succeed, you can confirm the "CPLD configured successfully (New version:2019/04/08)".

    10. (*) File:H3 StarterKit CPLD Update 20190408.zip

      <TIPS> If you fail, try another winPC or try USB HUB(WinPC -- USB HUB -- USB Cable -- H3 SK(CN12)).

    Limitation

      Yocto v3.4 or later don't support H3 v1.1 Starter Kit (RTP0RC7795SKBX0010SA00).
      Please use the H3 v2.0 SK.

    Q&A site

    http://renesasrulz.com/r-car-h3-m3-cockpit/

    FAQ page

    https://elinux.org/R-Car/Boards/Yocto-Gen3-CommonFAQ

    Appendix

    1. RTP0RC77951SKBX010SA03 board with 8GB DDR support is available in Yocto v3.9.0.
      <How to build>
      https://elinux.org/R-Car/Boards/Yocto-Gen3#Building_the_BSP_for_Renesas_H3_Starter_Kit.2C_M3_Starter_Kit
      1-1. after "step 10"
      Edit local.conf and select the board type
      Board type name H3_OPTION
      RTP0RC77951SKBX010SA03 1
      RTP0RC77951SKBX010SA00, RTP0RC77951SKBX010SA01 0 (default)

      Add the following lines to local.conf to enable 8GB support: 

      # For H3 SiP DDR 8GiB (2GiB x 4ch)                                                                                                                                                             
H3_OPTION_forcevariable = "1"

      1-2. after "step 11(12, 13)"
      You can find new dtb files in the images directory: 

      ls -1 tmp/deploy/images/h3ulcb/Image-r8a7795-h3ulcb-4x2g*.dtb
tmp/deploy/images/h3ulcb/Image-r8a7795-h3ulcb-4x2g-kf.dtb
tmp/deploy/images/h3ulcb/Image-r8a7795-h3ulcb-4x2g-vb2.1.dtb
tmp/deploy/images/h3ulcb/Image-r8a7795-h3ulcb-4x2g-vb2.dtb
tmp/deploy/images/h3ulcb/Image-r8a7795-h3ulcb-4x2g-vb.dtb

      ARM Trusted Firmware and U-Boot images will now have 8GB DDR support: 

      tmp/deploy/images/h3ulcb/bl2-h3ulcb.srec
tmp/deploy/images/h3ulcb/bl31-h3ulcb.srec
tmp/deploy/images/h3ulcb/cert_header_sa6.srec
tmp/deploy/images/h3ulcb/u-boot-elf-h3ulcb.srec


      Note: If you change "H3_OPTION", please clean before building. 

      # vi ./conf/local.conf
# bitbake -c cleanall arm-trusted-firmware u-boot
# bitbake arm-trusted-firmware u-boot
    • Retrieved from "https://elinux.org/index.php?title=R-Car/Boards/H3SK&oldid=520676"