Difference between revisions of "R-Car/Boards/Salvator-X-view"

From eLinux.org
Jump to: navigation, search
(initial)
 
(update)
Line 1: Line 1:
 
{{TOC right}}
 
{{TOC right}}
  
= Renesas Salvator-X =
+
= Renesas Salvator-X with MAXIM-RCAR-H3 camera board =
  
 
== Introduction ==
 
== Introduction ==
  
This is the Wiki for the Renesas R-Car H3 Salvator-X board (RTP0RC7795SIPB0010S).
+
This is the Wiki for the Renesas R-Car H3 Salvator-X board (RTP0RC7795SIPB0010S) with mounted MAXIM-RCAR-H3 camera board.
Refer to the [[R-Car]] page for information about Renesas' R-Car SoC family.
+
Refer to the [[R-Car/Boards/Salvator-X]] page for information about Renesas Salvator-X board.
 +
 
 +
== Build instructions ==
 +
 
 +
Refer to the [[R-Car/Boards/Yocto-Gen3]] page for information about buid procedure for Salvator-X-view board:
 +
  * target: salvator-x
 +
  * append: view
 +
 
 +
<pre>
 +
meta-renesas/meta-rcar-gen3/docs/sample/conf/salvator-x/linaro-gcc/bsp/*.conf
 +
MACHINE_FEATURES_append = " salvator-x-view"
 +
</pre>
  
 
== Serial Console ==
 
== Serial Console ==
Line 17: Line 28:
 
   * Kernel config: defconfig
 
   * Kernel config: defconfig
 
   * Kernel image: arch/arm64/boot/Image
 
   * Kernel image: arch/arm64/boot/Image
   * DTB: arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
+
   * DTB: arch/arm64/boot/dts/renesas/r8a7795-salvator-x-view.dtb
  
 
U-Boot boot command:
 
U-Boot boot command:
 
<pre>
 
<pre>
 
tftpboot 0x48080000 Image
 
tftpboot 0x48080000 Image
tftpboot 0x48f00000 r8a7795-salvator-x.dtb  
+
tftpboot 0x48f00000 r8a7795-salvator-x-view.dtb  
 
booti 0x48080000 - 0x48f00000
 
booti 0x48080000 - 0x48f00000
 
</pre>
 
</pre>
  
 
== Test procedures ==
 
== Test procedures ==
 +
 +
There are 2 sets (J1-J4 and J5-J10-J12-J13) with 4 cameras each (totally 8). Each set is independent, hence it is possible to connect only 4 cameras to any set.
 +
 +
The yocto build rootfs includes the test application that validates the cameras functionality:
 +
- the test application name 'capture', the source code location is "meta-renesas/meta-rcar-gen3/recipes-bsp/capture/files/capture.tar.gz"
 +
- to run 'capture' test example:
 +
$ /usr/share/tests/test_lvds_camera_0-3.sh
 +
- to update ov10640-ov490 camera firmware with specific resolution
 +
  
 
* [[Tests:SCIF-FIFO]]: Test SCIF FIFO behavior, using SCIF3 and HSCIF3 on expansion I/O connectors
 
* [[Tests:SCIF-FIFO]]: Test SCIF FIFO behavior, using SCIF3 and HSCIF3 on expansion I/O connectors

Revision as of 02:31, 27 July 2016

Renesas Salvator-X with MAXIM-RCAR-H3 camera board

Introduction

This is the Wiki for the Renesas R-Car H3 Salvator-X board (RTP0RC7795SIPB0010S) with mounted MAXIM-RCAR-H3 camera board. Refer to the R-Car/Boards/Salvator-X page for information about Renesas Salvator-X board.

Build instructions

Refer to the R-Car/Boards/Yocto-Gen3 page for information about buid procedure for Salvator-X-view board:

 * target: salvator-x
 * append: view
meta-renesas/meta-rcar-gen3/docs/sample/conf/salvator-x/linaro-gcc/bsp/*.conf
MACHINE_FEATURES_append = " salvator-x-view"

Serial Console

Use a micro-USB cable to connect to "Debug Serial 0". Serial settings are 115200 8N1.

Booting Linux

 * Kernel config: defconfig
 * Kernel image: arch/arm64/boot/Image
 * DTB: arch/arm64/boot/dts/renesas/r8a7795-salvator-x-view.dtb

U-Boot boot command:

tftpboot 0x48080000 Image
tftpboot 0x48f00000 r8a7795-salvator-x-view.dtb 
booti 0x48080000 - 0x48f00000

Test procedures

There are 2 sets (J1-J4 and J5-J10-J12-J13) with 4 cameras each (totally 8). Each set is independent, hence it is possible to connect only 4 cameras to any set.

The yocto build rootfs includes the test application that validates the cameras functionality: - the test application name 'capture', the source code location is "meta-renesas/meta-rcar-gen3/recipes-bsp/capture/files/capture.tar.gz" - to run 'capture' test example: $ /usr/share/tests/test_lvds_camera_0-3.sh - to update ov10640-ov490 camera firmware with specific resolution


  • Tests:SCIF-FIFO: Test SCIF FIFO behavior, using SCIF3 and HSCIF3 on expansion I/O connectors
  • Tests:SDIO-KS7010: Test SDIO with a Spectec SDW823 microSD card (using an SD size adapter) on connectors CN13 or CN14
  • Tests:SDIO-H3-Voltage-Switching: Test if voltages change properly when inserting UHS capable SD cards into connectors CN13 or CN14
  • Tests:Watchdog-Pretimeout: Test watchdog pretimeouts. Because the hardware watchdog (RWDT) doesn't support this feature, a software watchdog must be used in addition