R-Car/Boards/V3MSK

From eLinux.org
< R-Car
Revision as of 08:39, 19 December 2017 by Cogente (talk | contribs) (SW1 jumper tablet added)
Jump to: navigation, search

Introduction

This is the Wiki for the Renesas R-Car V3M Starter Kit board (RTP0RC7797....). Refer to the R-Car page for information about Renesas' R-Car SoC family.

Hardware

This section contains information about R-Car V3M Starter Kit board hardware.

Board Layout

V3m SK TOP Lables.png

V3m SK BOT Lables.png

Where to buy

TBD

V3M Starter Kit Board Documentation

TBD

System with LVDS cameras

TBD

Quick Start

Build BSP images

Please follow these instruction to build BSP http://elinux.org/R-Car/Boards/Yocto-Gen3-ADAS#Building_the_BSP_for_Renesas_ADAS_boards:

At step 5,6 - skip these steps
At step 8 - replace this step with following:

cp $WORK/meta-rcar/meta-rcar-gen3-adas/docs/sample/conf/v3msk/linaro-gcc/bsp/*.conf ./conf/

At step 9,10,11 - skip these steps
At step 13 - replace this step with following:

bitbake core-image-minimal

At step 16 use images for V3M Starter Kit board or ULCB Kingfisher board:

Image-r8a7797-v3msk.dtb
Image-r8a7797-v3msk-kf.dtb
Image-r8a7797-v3msk-kf-v0.dtb
Image-r8a7797-v3msk-vbm.dtb

NOTE: you can refer to http://elinux.org/R-Car/Boards/Yocto-Gen3-ADAS#Build_scripts_examples section and use scripts after adding append from steps 8,13

Build SDK

Please follow these instruction to build SDK http://elinux.org/R-Car/Boards/Yocto-Gen3-ADAS#Build_SDK

Flashing firmware

TBD

U-Boot Environment

Please follow these instruction to boot from network http://elinux.org/R-Car/Boards/Yocto-Gen3-ADAS#Loading_kernel_via_TFTP_and_rootfs_via_NFS
For V3MSK board you must use one of the following dtb files:

Image-r8a7797-v3msk.dtb
Image-r8a7797-v3msk-kf.dtb
Image-r8a7797-v3msk-kf-v0.dtb
Image-r8a7797-v3msk-vbm.dtb

ADAS test applications

TBD

Installing V3M Starter Kit Expansion Board

Use the following procedure to install Expansion Board to the V3MSK Board.

1. Dismount the back plastic plate from the R-Car V3M Starter Kit board.
1.1 Put the V3M Starter Kit board on the front panel to access to the hex standoffs.

Step 1.



1.2 Unscrew all hex standoffs and put away plastic back plate.

Step 2.



2. Aligning V3M Board Starter Kit to V3M SK Expansion Board.
2.1 Find COM Express connectors on both V3M Starter Kit and Expansion boards.
2.2 Align and carefully push them to each other until COM Express connectors are fully inserted.

To prevent the damage during connecting boards, apply the pressure mainly on the points marked with arrows on Step 3. picture.

Step 3.



2.3 Make sure that boards are aligning each other closely, without a gap.

No gap between the connected boards.



3. Check jumper position according to the Step 4. picture (marked with red).

Step 4.


Jumper SW1 controlls cameras power supply.

SW1 Jumper Settings
1-2 3-4 Vcameras
OFF OFF 5V
ON OFF 9V
ON ON 11V


4. Connecting Power and Communication cable.
4.1 Find automotive Power and Communication cable and it's port on the V3M SK Expansion Board.

Step 5.



4.2 Plug the Cable in the port. Make sure that the latch in the same position as shows Step 6. picture. and cable is placed to fit the port.

Step 6.



4.3 Start the cable insertion by pushing the latch's edge.

Step 7.



4.4 Finish the connection. Step 8. shows final latch position.

Step 8.



5. Now you can plug cameras to the Fakra ports.

Camera connected to the V3M SK Expansion Board


Automotive Power and Communication cable with USB adapter