Difference between revisions of "RPi Cases"
m (Added note about review of the IP Adelt case)
|Line 424:||Line 424:|
Revision as of 14:19, 20 August 2012
Back to RPi Hardware Basic Setup.
Hardware & Peripherals:
Hardware - detailed information about the Raspberry Pi boards.
Hardware History - guide to the Raspberry Pi models.
Low-level Peripherals - using the GPIO and other connectors.
Expansion Boards - GPIO plug-in boards providing additional functionality.
Screens - attaching a screen to the Raspberry Pi.
Cases - lots of nice cases to protect the Raspberry Pi.
Other Peripherals - all sorts of peripherals used with the Raspberry Pi.
As yet, the foundation does not provide cases for the Raspberry Pi. The small form factor or low power draw however, allow you to put it in almost everything.
I just had a go at knocking up a quick Lego case prototype. Since I don't know the metrics of all the connections, it's a bit of a "proof of concept" right now, but since's it's not exactly difficult to take out any offending side-pieces and move them if they're in the way of a beloved connector, I'm assuming that this isn't a big deal.
Also, because of the thin side-walls, a bit of additional hacksawing or dremeling shouldn't be too difficult.
I've limited myself to only using pieces that are currently available from Lego's "Pick a Brick" shop, in red. :)
I've tried to fit everything into an 8*12 grid footprint, which will hopefully fit … but I don't have the specs of the thickness of the thin wall-pieces, so no guarantees. One thing that might screw things up is the height of the board's connectors: I don't know whether they'll all fit within the upper and lower lip of the side-wall pieces. If the board's "USB port stack" is too high, I guess the "roof" could be raised by a tile or two.
I knocked it up with Lego's Digital Designer program (free download from their site). The critical Lego piece is the repeated hollowed-out "side wall" ("[") brick ("wall element 1*2*2, w. window"), which you'll find on LDD's parts palette behind the little "door" symbol, or under the Pick a Brick page, as element #4507686, design #60032 (red), cost 8 pence each.
Feel free to hack, mangle or otherwise rework.
Lego Case 2
I had a bit of a play in lego designer with the idea of a vertical case – the USB / ethernet would emerge from the top, and the power usb would be on the bottom – possibly using a right angled usb connector. It's possible to alter the sides to allow for gaps for the various bits that stick out. There are lots of transparent bricks available – also includes a 2 x 2 brick to stick the raspberry pi sticker on.
ICEberg Case V3 for Raspberry Pi
- First Case Aluminium with direct Coolling for CPU & LAN chipset
- Heat transfer with Silicon Thermal Pad
- Light LED Guide on the side (Option)
- 100% Aluminium machined CNC
- Case Design Pro
- GPU port available
- Upgrade with Vesa Mount
- Gloss finish
- Rubber foot
- Option with or without logo (ICEberg/Raspberry)
More information on BLOG ICEberg Case
Video V2 on youtube ICEberg Case V2 Aluminium for Raspberry PI
Shop Preorder now
Marco Alici Case for Raspberry Pi
Marco Alici, Italian Design Engineer, has designed this well appreciated clean enclosure to host the computer:
More infos on Marco's blog: http://marcoalici.wordpress.com
Raspi Case made a single sheet of polypropylen (PP)
Review of the Beta version of the case on the PiPod blog
Printable Mylar Sheet Fold-up Case
RaspberryPi.org forum user "eric_baird" thought of printing an outline of the walls of a case on a Mylar overhead projector (OHP) sheet or cardboard that could then be cut out and folded into a case. Multiple users have since drawn such cases that can be printed on a Mylar sheet, thick paper, card stock, cardboard. The printed parts can be cut with a sharp knife or scissors and then folded/assembled into the case.
Multiple models are available:
The foldable case from "tzj" (currently based on the model B beta board).
The foldable case from "Andrew K" is based on measurements of an actual Raspberry Pi model B and fits snugly.
The foldable case from Thomas Mueller is (arguably) a bit more stylish. It stays closed without glue, and can be re-opened.
Laser-cut Clear Acrylic Case
eBay UK seller guitarreriacom is offering a laser-cut clear acrylic case.
BRAMBLE Pi - Laser-cut Finger Jointed Wooden Case
Custom engraved Bramble Pi case
BRAMBLE Pi2 - laser engraved wooden case
Bramble Pi2 - Raspberry Pi laser engraved wooden case is also on sale on Etsy.com (Nhslzt). Laser cut and engraved with a bramble motif on both top and bottom.
Raspberry Pi Board B Enclosure
A solidworks concept from http://solidworksbootcamp.com/raspberry-pi-board-b-enclosure/
Raspberry Pi air case
Raspberry Pi fimo case
ModMyPi - Raspberry Topping Case
ModMyPi LTD was founded in February 2012 following the public release of the ground breaking Raspberry Pi Model B. ModMyPi LTD specialise in the manufacture of unique, professional and high-quality cases for the Raspberry Pi. ModMyPi is offering mix and match colour customisable cases for sale on their website.
Berry Box - The Lego compatible, transparent case for the Raspberry Pi
Raspberry Pi Cover - SK Pang electronics
Developed in-house and manufactured in the UK. A range of laser cut acrylic covers for the Raspberry Pi. Link
Pi-Stack Raspberry Pi enclosure
Developed in-house and manufactured in the UK. One of a range of compatible acrylic products designed exclusively for the Raspberry Pi. While everyone else seems determined to "cover up his beauty from the world", the Pi-Stack exposes the Raspberry Pi elegantly from all 4 sides. Unlike some of the other designs the makers claim that this also allows access to all the GPIO pins. Currently available in "Gold", "Silver" and black with 10mm acrylic base and top. Currently sold in USA, Canada and Australia as well as the UK, via Ebay.
Here's a link to a video showing how the Pi-STACK can be cable managed to reduce the maze of wires normally hanging off the Raspberry Pi management
RepRap friendly cover for Raspberry Pi
The Rep-Rap we have is not very reliable and is only really able to produce basic designs so this is a 6 part case that has to be glued together. There are 6 stl files here with construction notes.
Mega Drive / Genesis Case for Raspberry Pi
The design was thought up by osholt on the evening after receiving his Pi. The case is strictly DIY and an Instructable for it can be found at the Instructables website. The case is well suited to Green enthusiasts as it can easily be made with only reused or reclaimed parts as well as to emulation enthusiasts and to users with limited resources and design skill (you only need to know how to use a screwdriver to make the whole thing).
Our intention is to design a case for B model and provide that model of a functional protection, which all of us we will enjoy if you help me to achieve my objectives with your cooperation.
The RaspBox is made of two acrylic glass plates and four metallic spacers. All parts are hold together by eight screws. This minimalistic design comes from the Swiss company Yoctopuce. Originally, the RaspBox was just a pet-project, but as it was very appreciated within the company staff, the decision was made to bring it to the public. The design itself has been released under a Creative Commons Attribution-ShareAlike 3.0 License and can be downloaded from the product page. The finished product is also available from the Yoctopuce shop.
Two cases have been successfully printed on the makerbot so far. Both are vented for heat concerns. The main difference is one allows GPIO pin access directly.
Transparent cases for raspberry can be created using the case of a cassette tape. Simply drill and cut the holes that are needed into the case using a dremel.
Easy DIY case made from a CD and plastic CD protectors.
An 4€ RPi case
When having an RPi for 30€, buying a 15€ case is quit expensive. I decided to create this case. You just need :
- An 21x29.7 Art foam Cardboard
- Glues : sticker and gel
How to :
- Print the templates with the right scale
- Validate the sizes
- Glue the template on the board using the glue sticker
- Cut, assemble and glue using the glue gel
- If the RPi will stay powered for a long time. A few vent holes could be added
- Print a Raspberry Pi logo and glue it
The 3d views of the case, thank you Hervé C. for this nice design :
Made up of colorful layers sandwiched together between clear acrylic. Well received by the folks at the RaspberryPi foundation.
LCD Monitor Mount
PI LCD Mount from PC Supplies Limited (eBay), VESA 100 x 100 Standard Mount, Requires the 4xVESA Holes on your Monitor, Maybe not compatible if your monitor uses the VESA for the Base / Stand, Not compatible if you are already wall mounting your LCD Screen, Wafer Design, Motherboard is sandwiched between 2 wafers of clear shiny acrylic! Designed for Raspberry PI, Secured using 8 x M3 Nuts, Hex Spacers & Screws to allow you to build and unbuild, 4xM4 Spacers and 4xM4 Screws for the VESA Mounting. GPIO Compatible
PI Wafer Case from PC Supplies Limited, Wafer Design, Motherboard is sandwiched between 2 wafers of clear shiny acrylic!
Available from Amazon UK, Shipping throughout Europe Amazon UK
PI Box Case
Pi Box is the new Professional Case from PC Supplies Limited, Covers all sides of the motherboard for the ultimate protection. Unique Fit-together design with custom supplied 'PI Clips' Allows Access to SD Port / USB / Ethernet / Audio / Video / HDMI and PSU , No screws! and NO elastic bands! - "A true PRO design"
Available from Amazon UK, Shipping throughout Europe Amazon UK
PI Sandwich Case
BUD Industries is Proud to introduce The PI Sandwich Enclosure, designed for use with the Raspberry Pi microcomputer (not supplied) and to accommodate changes in component location on the board as well as the potential addition of components . The enclosures provide protection, flexibility and ease of access to all components with quick snap-in installation. This rectangular version is open on all four sides for direct access.
I bought two of these at Jameco Electronics in Belmont, CA for $7 each. It's okay, but the board is not held tightly in place. You wand to plug in cables and the SD card before the board is snapped into place because the board will pop out otherwise, and could break the plastic pieces. The two sides of the case are identical. You have to gently rock the sides back and forth to disassemble the case without breaking anything.
Simple sandwich case
Like me, most people do not have access to precision cutting tools like laser cutters. This makes it's rather difficult to do some of the intricate laser-cut case designs at home. So I decided to go with a simple sandwich case.
The case consists of:
- Two sheets of 75x120 mm polycarbonate
- Twelve 12 mm M5 countersunk hex screws
- Six 25 mm round spacers
The spacers have a notch at 6 mm which holds the board in place between the sheets of polycarbonate. Sadly, my design isn't optimal since one of the spacers covers the GPIO pins.
This isn't the most beautiful case but I hope it inspires people to be creative and build their own case instead of just buying one. Building is fun!
Barch Designs Aluminum Engraved Case
CNC Machined from Billet Aluminum. Mounting Holes in Bottom. Acts as a Heat Sink. LED Fiber Optics!
- GPIO Port Access
- LED indicators
- True Heatsink Design
- Curved Sleek Look
- Mountable to a desk or wall
- Nearly Indestructible
- Great Warranty
This is a production quality case designed to meet most RPi owners needs. There is a Kickstarter project trying to make this case available both with and without external screw terminal.
A convertible case - the Raspileon
The Raspileon can be changed from a housing for a server or home computer to a housing with access to the expansion ports. All without using tools. The Raspileon will be available in Germany at the end of August. More information and a short survey is available on this site (in German): http://plastikdrucker.de/page2/
The PiPod - a case built from a Really Useful Box
The PiPod case is a DIY project built from a "Really Useful Box" and cable ties. The two most important factors were a) Ability to mount a car rear-view monitor on top, b) protect the SD card by having it enclosed inside the case. More details on the Raspberry PiPod blog
The PiSlab - a quick and dirty mounting plate
The PiSlab is made from a slab of 1/4" aluminum and some PCB mounting clips (Mouser P/N 561-LMTP375). More details on this site
SBC Ltd Snap-together Pi case
This is a semi-transparent ABS case that gives access to all the Pi's connectors. It also incorporates light pipes for LEDs.
All in all I'm quite happy with it. What do you think?
Currently available on ebay