Difference between revisions of "RPi VerifiedPeripherals"

From eLinux.org
Jump to: navigation, search
(Working USB Hubs: Provided additional info. w.r.t. Gembird USB 2.0 Switching Hub UHS242)
(E3372)
 
(475 intermediate revisions by more than 100 users not shown)
Line 27: Line 27:
 
'''Model B Hardware Revisions and USB Power limits'''
 
'''Model B Hardware Revisions and USB Power limits'''
 
'''Hardware Revision 1.0'''
 
'''Hardware Revision 1.0'''
The original Model B board had current limiting polyfuses which limited the power output of each USB port to approximatly 100 mA. USB devices using more than 100 mA had to be connected via a powered hub. The Raspberry Pi's PSU was chosen with a power budget of 700 mA of which 200 mA were assigned to the USB ports, so the Raspberry Pi's (poly)fuses were designed only for devices up to 100 mA, and typical 140 mA polyfuses will have as much as 0.6 volt across them when drawing currents near the 100 mA limit. As a consequence the USB ports are only directly suitable for "single current unit" USB devices which, according to USB specifications, are designed to work with just 4.4 Volt. Not only do non single current unit devices draw more current (causing greater Voltage drops, and greater stress on the fuses), they also might require 4.75 Volt to work.
+
The original Model B board had current limiting polyfuses which limited the power output of each USB port to approximately 100 mA. USB devices using more than 100 mA had to be connected via a powered hub. The Raspberry Pi's PSU was chosen with a power budget of 700 mA of which 200 mA were assigned to the USB ports, so the Raspberry Pi's (poly)fuses were designed only for devices up to 100 mA, and typical 140 mA polyfuses will have as much as 0.6 volt across them when drawing currents near the 100 mA limit. As a consequence the USB ports are only directly suitable for "single current unit" USB devices which, according to USB specifications, are designed to work with just 4.4 Volt. Not only do non single current unit devices draw more current (causing greater Voltage drops, and greater stress on the fuses), they also might require 4.75 Volt to work.
  
 
'''Model B Hardware Revision 2.0 and Revision 1.0 with ECN0001 change'''
 
'''Model B Hardware Revision 2.0 and Revision 1.0 with ECN0001 change'''
This had the polyfuses removed, removing the 100 mA current limitation for each USB port (but leaving the main fuse F3 intact). Users should still ensure their power supply can power the Raspberry Pi and the USB peripherals. Revision 2.0 was released in August 2012.
+
This had the polyfuses removed, removing the 100 mA current limitation for each USB port (but leaving the main fuse F3 intact). Users should still ensure their power supply can power the Raspberry Pi and the USB peripherals. Revision 2.0 was released in August 2012. {{Warning|}}Because the polyfuses have been removed, back feeding of the PI, by applying power via its normal USB output, can damage D 17 if triggered by an over-voltage, and so lead to consequential over-heating. This can be discovered by melts, scorching, smoke or worse.[http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=34149]
  
 
==Linux Driver Issues==
 
==Linux Driver Issues==
Line 37: Line 37:
  
 
== Powered USB Hubs ==
 
== Powered USB Hubs ==
A number of low-cost powered USB hubs are known to have caused problems. Members of the Raspberry Pi forums have reported low power or no power at all in some cases. The following is a list of specific Powered USB Hubs which appear to be fault-free. Please note that these do not take into account powering the Raspberry Pi from the hub, in addition to its peripherals.
 
 
If you use a powered hub and the Raspberry Pi PSU together consider powering them from the same power bar with switch, so you can turn them on simultaneously., especially if the HUB tries to feed the Raspberry Pi through their interconnect cable, due to the 100 mA limiting fuse in the Raspberry Pi, the Raspberry Pi will be partially powered which may cause problems (unwanted writes to the SD card).
 
  
===Working USB Hubs===
+
This section has been moved to a separate page. See [[RPi Powered USB Hubs]]
<div style="margin: -.3em -1em -1em -1em;">
 
{| width="100%" bgcolor="#fff" border="0" cellpadding="2px" cellspacing="2px" style="margin:auto;"
 
|- align="center" bgcolor="#e7eef6"
 
| '''Brand'''
 
| '''Name'''
 
| '''Model Number'''
 
| '''Hardware ID'''
 
| '''USB Version'''
 
| '''Number of Ports'''
 
| '''Power Rating*'''
 
| '''Powers Raspberry Pi'''
 
| '''Additional Information'''
 
  
 +
== USB Remotes ==
 +
* The [http://www.pi-supply.com/product/flirc-usb-ir-remote-dongle-for-raspberry-pi/ FLIRC] USB dongle allows the use of any remote control with your Raspberry Pi. Configure the device on your desktop PC, then simply plug into your Pi for a perfect media center companion. Available from [http://www.pi-supply.com/ Pi Supply] and [http://thepihut.com/ The Pi Hut]
  
|- valign="top" align="left" style="background: #F5FAFF;"
+
* ASUS TV FM Remote IR - ID 3353:3713 - works. Receiver connected to an USB Hub. Tested with archlinux in X. It works also as pointer (pressing "Toggle" button)
|Belkin
 
|4-Port Ultra-Slim Desktop Hub
 
|F4U040
 
|05e3:0608
 
|USB 2.0
 
|4-Port
 
|5&nbsp;V - 2.6&nbsp;A
 
|Not Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 4-Port Hub
 
|F5U224
 
|
 
|USB 2.0
 
|4-Port
 
|5&nbsp;V - 500&nbsp;mA per Port
 
|Not Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|TetraHub™ USB 2.0 4-Port Hub
 
|F5U231
 
|
 
|USB 2.0
 
|4-Port
 
|5&nbsp;V - 500&nbsp;mA per Port
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 4-Port Hub
 
|F5U234
 
|
 
|USB 2.0
 
|4-Port
 
|5&nbsp;V - 500&nbsp;mA per Port
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 7-Port Hub
 
|F5U237
 
|
 
|USB 2.0
 
|7-Port
 
|5&nbsp;V - 3.8&nbsp;A
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|MyEssentials 7-Port High-Speed USB 2.0 Hub
 
|F5U259-ME
 
|
 
|USB 2.0
 
|7-Port
 
|
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 4-Port Lighted Hub
 
|F5U403
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Not Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 7-Port Lighted Hub
 
|F5U700
 
|
 
|USB 2.0
 
|7-Port
 
|
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hub 2-en-1
 
|F5U706ea
 
|
 
|USB 2.0
 
|7-Port
 
|
 
|Not Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Hi-Speed USB 2.0 7-Port Hub
 
|F5U237v1
 
|
 
|USB 2.0
 
|7-Port
 
|5&nbsp;V - 2.5&nbsp;A
 
|Not Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Belkin
 
|Ultra-Slim Desktop Hub
 
|F4U039qukAPL
 
|05e3:0608
 
|USB 2.0
 
|7-Port
 
|
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Benq
 
|
 
|E2220HD
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Verified
 
|Monitor with built in Hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Biltema
 
|
 
|23-924
 
|
 
|USB 2.0
 
|4-Port
 
|2.0&nbsp;A
 
|Verified
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|C3 Tech
 
|7 Port Hub
 
|HU-7201 BK
 
|1a40:0201
 
|USB 2.0
 
|7-Port
 
|5&nbsp;V - 2.0&nbsp;A
 
|Not Verified
 
|Backpowering - Mod hub or cut red wire in uplink cable.
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Cyberpower
 
|High-speed Hub
 
|CP-H720P
 
|0409:0050
 
|USB 2.0
 
|7-Port
 
|3.6&nbsp;A
 
|Verified
 
|May Contain dual 05e3:0608 instead of 0409:0050
 
  
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Dell
 
|
 
|2001FP
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Not Verified
 
|Monitor with built in Hub
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Dell
 
|
 
|SP2309W
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Not Verified
 
|Monitor with built in Hub
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Dell
 
|
 
|2407FWP
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Not Verified
 
|Monitor with built-in hub - 6-in-1 card reader Works, but it cannot read SDXC
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Dell
 
|
 
|U3011
 
|
 
|USB 2.0
 
|4-Port
 
|
 
|Not Verified
 
|Monitor with built in Hub - Card Reader Works - May work with SDXC
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Delock
 
|
 
|B/N61393
 
|
 
|USB 2.0
 
|4-Port
 
|2.0&nbsp;A
 
|Verified
 
|
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Delock
 
|USB 2.0 External Hub 7 Port
 
|B/N87467
 
|
 
|USB 2.0
 
|7-Port
 
|5&nbsp;V - 3.5&nbsp;A
 
|Verified
 
|You can Power Raspberry Pi using one USB Port of the Hub there is no backfeeding, measured 4,88V on Idle and 4,82V on load on TP1-TP2.
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Deltaco
 
|
 
|UH-715 Rev 2
 
|
 
|USB 2.0
 
|7-Port
 
|2.0&nbsp;A
 
|Not Verified
 
|
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Dynex
 
|
 
|
 
|0409:0050
 
|USB 2.0
 
|7-Port
 
|2.0&nbsp;A
 
|Not Verified
 
|
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|D-Link
 
|DUB-H7 High Speed USB 2.0 7-Port Hub
 
|BUBH7A A5
 
|
 
|USB 2.0
 
|7-Port
 
|2.0&nbsp;A
 
|Not Verified
 
|[http://www.amazon.com/D-Link-DUB-H7-High-Speed-7-Port/dp/B00008VFAF]
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|D-Link
 
|DUB-4 High Speed USB 2.0 7-Port Hub
 
|DUB-H4
 
|
 
|USB 2.0
 
|4-Port
 
|2.0&nbsp;A
 
|Verified
 
|[http://www.newegg.com/Product/Product.aspx?Item=N82E16817111131] Charging port doesn't power Raspberry Pi
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Digicom
 
|
 
|
 
|
 
|USB 2.0
 
|4-Port
 
|5&nbsp;V - 2.0&nbsp;A
 
|Not Verified
 
|[http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/MiniHubUsb204P#]
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|mbeat
 
|13 Port USB Hub
 
|USB-M13HUB
 
|
 
|USB 2.0
 
|13-port
 
|5V - 3A
 
|Verified
 
|
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Monoprice
 
|Aquagate USB Hub
 
|5328
 
|
 
|2.0
 
|7-port
 
|2.0&nbsp;A
 
|Verified
 
|Has separate USB In port, in theory should prevent backfeeding (but that is not verified). get about 4.9V across TP1/TP2 when idling with Raspbian. [http://www.monoprice.com/products/product.asp?c_id=103&cp_id=10307&cs_id=1030702&p_id=5328&seq=1&format=4]
 
 
|-
 
|}
 
 
 
'*' Power Ratings may not be completely accurate, use as rough guideline rather than fact.
 
</div>
 
 
 
*'''Acme'''
 
** USB 2.0 hub 4 port ([http://www.acme.eu/en-us/product/019188 ACME]) Based on NEC μPD720114 USB2.0 Hub Controller USB ID 0409:005a  '''NOTE!''' It is bus-powered hub, but it is very cheap and small and works after a small modding: on USB-hub board you have 4 holes: V, D+, D- and GND. Connect GND, D+ and D- to the Raspberry Pi, and additionally connect GND and +5&nbsp;V from power supply to the same holes on USB-hub GND and V. Now there is common contacts: GND, D+ and D- between Raspberry Pi and hub needed to work, and additional power for USB devices, connected to the hub. Tested on my Raspberry Pi.
 
 
 
*'''Digitus'''
 
** 7-port USB2.0 Powered Hub. Model DA-70226.
 
*'''Eminent'''
 
** [http://www.eminent-online.com/en/product/22/em1102-4-port-usb-hub---black.html] EM1102 4 Port USB 2.0 Hub with 1&nbsp;A power adapter. It's able to power the Raspberry Pi, external HDD and other peripherals.
 
** [http://www.eminent-online.com/en/product/27/7-port-usb-2-0-hub.html] EM1107 7 Port USB 2.0 Hub with 2&nbsp;A power adapter. It's able to power the Raspberry Pi, external HDD and other peripherals.
 
* '''GearHead'''
 
** [http://www.amazon.com/gp/product/B004OBZ088/] GearHead 4 Port Hub with Energy Saving Power Switch (5&nbsp;V, 1&nbsp;A)
 
*'''Gembird'''
 
** Gembird UHS 242 4-port USB 2.0 Hub (5V DC, 1A). '''NB:''' This is a 4-port switching hub that enables the "sharing" of up to four USB devices between two computers. Whilst it may be powered externally, it does take power from both connected computers. If one of them is, say, a netbook or laptop, that may provide sufficient extra power to enable the use of USB devices that the Pi alone cannot handle.
 
* '''Genesys Logic (sold at Fry's)'''
 
** Genesys Logic 4-Port USB 2.0 Hub (ID 05e3:0608) (Other brands include Gigaware and Belkin, same ID shows up in lsusb)
 
** Genesys Logic 4-Port USB 2.0 Hub (ID 05e3:0606) (Other brands include i-Rocks, same ID shows up in lsusb)
 
* '''Hama'''
 
** Hama 4-way USB 2.0 Hub
 
*'''HP'''
 
** HP ZR2240w 21.5" Monitor with built in 2-Port USB Hub (B)
 
* '''König Electronic'''
 
** CMP-USB2HUB55 - 7 port USB2.0 HUB, (ID 1a40:0201 Terminus Technology Inc. Hub) 2.0&nbsp;A power supply, backpowers Raspberry Pi well.
 
*'''Laser'''
 
** "7 port USB hub with AC adapter Version 2.0".  5&nbsp;V 1&nbsp;A (found at Harvey Norman Australia for $24.95 and Australia Post Shops for $9.95).  You can power the Raspberry Pi by connecting both the main USB connector to the Raspberry Pi USB port, '''and''' from a spare USB port back to the power micro USB socket.  If you don't do both, boot-loops are likely to occur.
 
*'''Logik'''
 
** [http://www.currys.co.uk/gbuk/logik-lp4hub10-4-port-powered-usb-hub-04979038-pdt.html] LP4HUB10 4-Port USB Hub.  '''Throws errors when used with Fedora remix 14'''
 
** Logik L4THUB10 4 Port powered hub works fine under Raspbian/Wheezy/model B. Captive USB cable, 2&nbsp;A power supply, convenient single top mounted USB socket. Unlike my last hub, will power Wi-Fi!
 
*'''LogiLink'''
 
** UA0085 USB 2.0 Hub, 4-Port  with PSU 5&nbsp;V, 2&nbsp;A
 
** UA0091 USB 3.0 Hub, 4-Port  with PSU 5&nbsp;V, 4&nbsp;A. Connected with USB2.0 cable. 1&nbsp;A per port, able to support USB HDD drives and other power hungry devices. Tested with kernel 3.1.9-cutdown, Wheezy.
 
** UA0096 USB 2.0 Hub, 10-Port  with PSU 5&nbsp;V, 3.5&nbsp;A (Not suitable for powering Raspberry Pi because it doesn't work unless there is working USB input present even with PSU plugged in.)
 
** UA0160 USB 2.0 Hub, 4-Port  with PSU 5&nbsp;V, 2&nbsp;A. Able to power the Raspberry Pi, keyboard, mouse and LogiLink UA0144 USB Ethernet adapter. (More testing to come.)
 
* '''Macally'''
 
** [http://www.macally.com/EN/?page_id=2312] Hi-Speed 7-Port USB 2.0 Powered Micro HUB, AC Powered. Includes a 2000&nbsp;mA wall-wart (US style)
 
* '''Manhattan'''
 
** [http://manhattan-products.com/en-US/products/6500-hi-speed-usb-2-0-micro-hub] (#160612) Hi-Speed USB 2.0 Micro HUB, AC Powered (identifies as ID 05e3:0608 Genesys Logic) Includes a 1000&nbsp;mA wall-wart (US style)
 
** [http://manhattan-products.com/en-US/products/9583-mondohub] (#161718) MondoHub 28 Port USB 3.0 & USB 2.0 HUB (24 USB 2 ports @500&nbsp;mA each) + (4 USB 3.0 Ports @900&nbsp;mA each) Power Switches on each port, AC Powered and Includes a 5&nbsp;V 4&nbsp;A wall-wart (US style)
 
*'''Newlink'''
 
** NLUSB2-224P 4 port USB 2.0 Mini hub with PSU 5&nbsp;V 1&nbsp;A
 
** NLUSB2-222P 4 port USB 2.0 Hub with 5&nbsp;V 2&nbsp;A PSU (Available From [https://www.modmypi.com/shop/raspberry-pi-accessories/New-Link-4-Port-USB-Hub-(USB-2.0-with-Mains-Adaptor) | ModMyPi])
 
*'''Nilox'''
 
** Nilox USB 2.0 4port HUB model HUB4USB2AC with PSU 5&nbsp;V 1.0&nbsp;A
 
* '''Plugable'''
 
** [http://plugable.com/products/USB2-HUB4BC/] USB2-HUB4BC 4 Port USB 2.0 Hub with BC 1.1 Fast Charging. 5&nbsp;V 2.5&nbsp;A power supply. Powering Raspberry Pi via microUSB from a hub port. USB Audio peripheral tested and working.
 
** [http://plugable.com/products/USB2-HUB-AG7/] USB2-HUB-AG7 7 Port USB 2.0 Hub with 5&nbsp;V 3&nbsp;A power supply. There are US and UK power supply versions and it can be ordered in US and (for the UK version) many countries in Europe. There is a video showing this hub powering both the Raspberry Pi several peripherals at once[http://www.youtube.com/watch?v=pDA7MxFtoS0]. 
 
* '''Pluscom'''
 
** Pluscom 7 Port USB 2.0 Hub Model U7PH-3A with 3&nbsp;A PSU. USB ID 1a40:0101. Powering Raspberry Pi via microUSB from a hub port. Internally two 4 Port switches linked. Leaks power back up USB data cable to Raspberry Pi, but it is not really a problem when powering Raspberry Pi at the same time.
 
*'''Satechi'''
 
** ST-UH12P 12 port powered hub with 2 Control Switches. Also works while powering the Raspberry Pi.
 
*'''Staples (Business Depot) (Bureau EN GROS)'''
 
**  Staples 4-port hub Item 607477-CA
 
*'''StarTech.com'''
 
**  StarTech.com 7-port Compact USB 2.0 Hub (ST7202USB). Comes with 5&nbsp;V 2&nbsp;A supply. Shows in lsusb as two Genesys Logic, Inc. USB-2.0 4-Port HUBs (05e3:0608). Back powers Raspberry Pi (just, voltage across TP1 & TP2 is a little low when powered from this hub).
 
*'''SumVision'''
 
**  Sumvision Slim 4 Port High Speed USB 2.0 HUB with PSU 5&nbsp;V 1.0&nbsp;A (from [http://www.7dayshop.com/catalog/account_history_info.php?page=1&order_id=5130107 | 7dayshop ])
 
*'''Sitecom'''
 
** CN-032 4 Port USB 2.0 Pocket Hub. Works for powering the Raspberry Pi, an USB WLAN Adapter, wireless Kbd+Mouse. Using an 2500&nbsp;mA Voltcraft
 
** CN-060 4 Port USB 2.0 Hub powered with AC Adapter (1&nbsp;A). Powering Raspberry Pi via microUSB from a hub port.
 
** CN-061 7 Port USB 2.0 Hub powered with AC Adapter. There is a voltage problem on the left half of the hub (4 ports) that do not deliver enough current to feed a wifi dongle (tested with an RTL8191S). The remaining 3 ports on the right half are instead working as expected. [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=24247]
 
*'''Sweex'''
 
** US014 4 Port USB 2.0 Hub
 
*'''Targus'''
 
** ACH81xx 7-port powered hub. 5&nbsp;V 3&nbsp;A power supply, with 2 high power ports. (possible conflicting behaviour with USB keyboard / Wi-Fi Dongles)
 
** ACH63EU 4-port. Using a 5&nbsp;V 2&nbsp;A power supply, which isn't supplied with the hub, it is able to power the Raspberry Pi as well.
 
*'''The Pi Hut'''
 
** 7 Port USB Hub (from [http://thepihut.com/products/7-port-usb-hub-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
*'''Trendnet'''
 
** [http://www.trendnet.com/products/proddetail.asp?prod=130_TU2-700&cat=49] TU2-700 7 Port Powered USB 2.0 Hub with AC Adapter (5&nbsp;V 2&nbsp;A)
 
*'''Tripp-Lite'''
 
** [http://www.tripplite.com/en/products/model.cfm?txtModelID=3167] U222-007-R 7 Port Powered USB 2.0 Hub with AC Adapter (5&nbsp;V 2.5&nbsp;A) Powering Raspberry Pi from the hub works.
 
*'''Ultron'''
 
** [http://www.ultron.de/v1/produktansicht.php?artnr=67072&kid=bfa8340c4e245...&l=en&WGType=Neue+USB-HUBS] UHN-710 7-port powered hub with PSU 5&nbsp;V, 3&nbsp;A. USB ID 1a40:0201.
 
*'''VANTEC'''
 
** 4 Port USB 2.0 Powered Hub Model: UGT-MH304. 5&nbsp;V 2&nbsp;A AC/DC adapter. Go 2.0 Mini hub.
 
*'''Z-TEK'''
 
** Z-TEK 7-port powered hub with PSU 5&nbsp;V, 4&nbsp;A. USB ID 1a40:0201.
 
*"Unknown"
 
** 10(7-4) port hub idVendor=1a40, idProduct=0201 / idVendor=1a40, idProduct=0101 works
 
 
===Problem USB Hubs===
 
 
Please check known workarounds [http://elinux.org/Rpi_USB_check-list here] before adding to the list
 
 
*'''Addon'''
 
** 7-Port Powered Hub - labelled ADDUH070P - Gives constant Eth0 errors on boot.
 
*'''Belkin'''
 
** 7-Port Powered Mobile Hub - device labelled F4U018, packaging labelled F5U701. lsusb reveals it to be two Genesys Logic 4-port hubs based on the GL850G chipset (vendor: 0x05e3 product: 0x0608) ganged together. Yields a lot of "handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK" errors and device resets in /var/log/messages. Low speed devices such as keyboards work OK, Wi-Fi/mass storage is unreliable or broken. -- No error messages with the latest kernel, but it is still unstable with mass storage devices. Also, leaks current back to the Raspberry Pi (can be fixed by overtaping GND and +5&nbsp;V pinouts)
 
** F4U022 7-Port powered USB hub (powered 5&nbsp;V, 2.6&nbsp;A), same as F4U018
 
** 7-Port Powered Hub - device labled F5U237 Rev.3 - ID 050d:0237 Wired Ethernet fails to connect; gives "DWC OTG HCD URB enqueue failed adding QTD. Error status -4008" Result is same as DUB-H7 below.
 
** F5U404 Hi-Speed USB 2.0 4-Port Mobile Hub. Faulty/bad design; Leaks current back up the cable to the Raspberry Pi.
 
** F5U307 Hi-Speed USB 2.0 7-Port Hub (Powered, able to apply power to Raspberry Pi via micro USB from this hub at same time) It work's sometimes. (Works always without powering the Raspberry Pi, haven't tried that)
 
 
*'''Dell'''
 
** Dell U2410 Monitor Built-in 4 Port Hub - Shows up as a pair with 0424:2514 and 0424:2640. Standard Microsystems Corp. USB 2.0 Hub. When connecting some devices it kills the Ethernet with "smsc95xx 1-1.1:1.0: eth0: Failed to read register index 0x0000011X" errors. It did work for a keyboard and webcam. Bluetooth that works connected directly to the Raspberry Pi triggers the error.
 
 
*'''DELTACO'''
 
** 7-Port USB Hub UH-713 Rev 3. This one consists also of two 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUBs connected together. The power supply is rated at 5 V 2 A. It kills Ethernet when X11 is started.
 
 
*'''Dynex'''
 
** 7-Port USB Hub - Does not work in Debian 19-04 image.
 
** DX-HB7PT 7-Port USB Hub - As per the Gear Head below, it's 2 daisy-chained Genesys Logic 05e3:0608 devices. Appears to result in significant slow downs when the USB is under load, such as running the root filesystem from a USB drive.
 
 
*'''Dynamode'''
 
** 7-Port USB 2.0 Hub (Silver and black). Feeds power back up the interconnect to the Raspberry Pi causing the power LED to light on the Raspberry Pi if the hub is powered on, but the Raspberry Pi is not. The Raspberry Pi also fails to boot when powered off this hub, with or without the interconnect plugged in. Stops the network from working when connected to the Raspberry Pi after booting the Raspberry Pi - cannot ssh to the Raspberry Pi. Best avoided. :-( Shows up in ''lsusb'' as a pair of ''ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB'' which is interesting. - Confirmed.  This hub also appears unable to power an external USB drive using a y-cable as it gives the error -71 message in dmesg (when providing external power to the Raspberry Pi).
 
** 4-Port High-Speed USB 2.0 Hub (USB-H40-A2.0), came with with a 1&nbsp;A power supply. Leaks power to the Raspberry Pi through the uplink. Doesn't work with Raspberry Pi, unless the Raspberry Pi is powered by a second power source. This hub is completely generic and I've seen it being sold under different brand names as well. Therefore, a picture is [http://i.imgur.com/BPZ3j.jpg included] for easy identification.
 
 
*'''D-Link'''
 
** 7-Port USB Hub DUB-H7 (Crashes USB stack, including Ethernet, when plugging / using some peripherals). (See note above, it works with some distros and/or with latest firmware)
 
 
*'''E-Solution'''
 
** 4-Port 2&nbsp;A Supply (Does not detect at all during boot or after boot- no messages) [IC = Alcor Micro Corp (AU6254)]
 
 
*'''Fosmon'''
 
** 7-Port USB 2.0 Hub with 1&nbsp;A Power Supply (Causes interference with other USB devices and sends enough power to light up the Raspberry Pi with it's Micro USB cable unplugged).
 
 
*'''Gear Head'''
 
** UH7250MAC 7-port powered hub. Internally, two daisy-chained Genesys Logic 05e3:0608 devices. Causes Ethernet instability when used under very specific circumstances, in X11.
 
** <strike>UH5200T 4-port powered hub. As of 2012-08-16 Wheezy, if any USB 1.x device (a keyboard, for example) is plugged into this hub, Ethernet stops, and USB interrupts for other devices get dropped (keys repeating forever), etc.  Occurs even if power is not attached (not a power leakage problem).</strike>  Appears working after a bootloader and/or firmware update on 9/12.  Also, turned out to be somewhat more specific to the combination of two particular low-speed devices.
 
 
*'''Hama'''
 
** 4-Port USB 2.0 "bus hub", model 78496 (?). Only works for low power devices (card readers?), but it does not work for power hungry devices (HDD and WLAN). It doesn't boot when hub connected to Raspberry Pi. The funniest thing is that Raspberry Pi powers on when I plug in this hub to normal size USB port (not that small dedicated port). idVendor=05e3, idProduct=0608
 
 
*'''Kensington'''
 
** 7-Port Dome Hub model no 1500129 (Possible problems with malfunctioning keyboard, kills mouse when GUI started).
 
 
*'''iBall'''
 
** Piano 423 4-Port USB hub. Listed in lsusb as Genesys Logic. Fails to deliver enough power to connected devices even when using AC power suply.
 
 
*'''Inland'''
 
** 4-Port USB 2.0 Cable Hub model no 480426 (Some devices work, some don't, cheap unshielded untwisted wire design)
 
 
*'''Logik'''
 
** LP7HUB11 7-Port USB Hub. (Ethernet failed, slow response, in LXDE. Happened whether or not the hub's independent power supply was connected to the hub.)
 
 
*'''Soniq'''
 
** 4-Port 5&nbsp;V supply. Model number CUH100. (B). Appears to draw power away from the Raspberry Pi, even when the Raspberry Pi has an isolated power line. Netgear WNA1100 Wi-Fi Adapter (which is known to work in other setups is recognized, but it is unresponsive).
 
 
*'''Targus'''
 
** ACH115EU 7-port powered hub. 5&nbsp;V 3&nbsp;A power supply. Arduino communicates with Raspberry Pi when connected directly to Raspberry Pi's USB port, but it hangs as soon as if connected via ACH115. Also sometimes smsc95xx eth0 Failed to read register index 0x00000114 etc. errors in syslog when used.
 
 
*'''TCM'''
 
** Model 234298 s/n T634007737 powered hub. 4 ports plus card reader. 1&nbsp;A power supply. Model B, Wheezy Raspbian works OK with keyboard/mouse, but there are problems with Wi-Fi no connects. (insufficient power?)
 
 
*'''Trust'''
 
** 10-port USB 2.0 Hub (powered). Prevents Ethernet from being recognised.
 
** SliZe 7 port USB 2.0 Hub (powered) - Item number 17080 (Barcode 8 713439 170801). Prevents Ethernet from being recognised. Keyboard sends multiple characters.
 
 
*'''Unbranded / Multiple Brands'''
 
** 7-port silver/black hub. Also sold elsewhere under brands such as 'EX-Pro', 'Trixes' and 'Xentra' -- This is ''probably'' due to an inadequate power supply. -- I replaced the terrible power supply with a very good one, kept getting "DEBUG: handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK" in dmesg, with no devices plugged in to the hub (with or without the power supply in). Measurements by [[User:TrevorGowen|TrevorGowen]] ([[User talk:TrevorGowen|talk]]) of the power loading behaviour of an example of this type of hub and its supplied PSU are logged at [http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/PoweredUSBHubs.html CPM-Spectre-Pi...PoweredUSBHubs], together with similar measurements of other devices.
 
** Generic 7-port black hub with Genesys Logic GL850A chipset
 
** Cerulian 10 Port USB 2.0 Top Loading Hub with 2&nbsp;A supply (kills mouse and network port)<ref>http://www.raspberrypi.org/forum/absolute-beginners/cheap-powered-usb-hub-uk/#p76452</ref>
 
** [http://www.monoprice.com/products/product.asp?c_id=103&cp_id=10307&cs_id=1030701&p_id=226 USB 2.0 4 PORT INT/EXT DUAL HUB BAY] -- Genesys Chipset -- idVendor=05e3, idProduct=0607 -- low speed devices worked, but there are strange USB failures when X session started.  High speed devices such as hard drives had failures.
 
 
== USB Remotes ==
 
 
* ATI Remote Wonder (X10 Wireless Technology, Inc. X10 Receiver) — ID 0bc7:0004 — appears as a joystick-like 2 button mouse and a 0-9 keypad without drivers on console and X.
 
* ATI Remote Wonder (X10 Wireless Technology, Inc. X10 Receiver) — ID 0bc7:0004 — appears as a joystick-like 2 button mouse and a 0-9 keypad without drivers on console and X.
  
Line 531: Line 50:
  
 
* [http://www.ipazzport.com/02A.html iPazzport] mini 2.4&nbsp;GHz wireless keyboard and touchpad.  
 
* [http://www.ipazzport.com/02A.html iPazzport] mini 2.4&nbsp;GHz wireless keyboard and touchpad.  
 +
 +
* Pan.Code D1000 - 2.4GHz Wireless keyboard and touchpad.
  
 
* [http://www.ortek.com/html/pdt_view.asp?area=46&cat=152&sn=76 PKB 1800] Wireless Smart Pad ad Mini Keyboard. The pad works as a mouse, but not multi touch features. The keyboard works.
 
* [http://www.ortek.com/html/pdt_view.asp?area=46&cat=152&sn=76 PKB 1800] Wireless Smart Pad ad Mini Keyboard. The pad works as a mouse, but not multi touch features. The keyboard works.
Line 541: Line 62:
  
 
== USB Keyboards ==
 
== USB Keyboards ==
USB keyboards that present themselves as a standard HID (Human Interface Device) device should work.  '''Please be aware that some of these keyboards were probably used with a powered hub'''
 
=== Working USB Keyboards ===
 
The following is a list of specific keyboards known to work and which appear to work fault-free.
 
 
* '''A4 Tech'''
 
** Model KL-5 USB Keyboard, 20&nbsp;mA.
 
 
* '''ABS'''
 
** M1 Heavy Duty Professional Gaming Mechanical Keyboard (B)
 
 
* '''Action Star'''
 
** ACK-5010U Mini Keyboard And Mouse
 
 
* '''Accuratus'''
 
** KYB-Toughball-HI
 
 
* '''Acer'''
 
** KG-0917 Wireless Keyboard And Mouse Bundle  (B)
 
** KU-0906 Compact Keyboard (B) (Also known as Genius LuxeMate i200 Keyboard)
 
** SK-9625 Multimedia Keyboard (B) (multimedia functions not tested)
 
 
* '''Adesso'''
 
** [http://ergoprise.com/product_images/j/699/ADP-PU21_big__14173_zoom.jpg PS/2 to USB Adapter] ADP-PU21, 100&nbsp;mA (tested only with keyboards) Any PS/2 keyboard will work only if it will work with a reduced operating voltage.
 
** Model AKB-410UB. Keyboard with Touchpad.
 
 
* '''Apple'''    (Apple keyboards that have USB ports require an external powered hub to work, and do not work on the Raspberry Pi directly! Note: Apple keyboard works fine using the latest Raspberry Pi, even when connected directly (and with mouse connected))
 
** [http://upload.wikimedia.org/wikipedia/commons/thumb/e/ea/Apple_iMac_Keyboard_A1243.png/800px-Apple_iMac_Keyboard_A1243.png Apple Keyboard with Numeric Keypad (aluminium/wired) A1243]
 
** [http://upload.wikimedia.org/wikipedia/commons/8/81/Apple_Keyboard_A1242.jpg Apple Keyboard (aluminium/wired) A1242]
 
 
* '''Asda'''
 
** Basic Wired Keyboard HK2026 (B)
 
** Basic Wired Keyboard HK3014
 
*** (Please note when I put this keyboard through Newlink USB hub, it didn't work as expected)
 
** Premium Wireless Keyboard (white keys, silver back) HK8028
 
** Wireless Multimedia Deskset (keyboard, mouse and USB dongle) Model: HKM8016B (Note: Shown on Asda Website as HK8016B) (B)
 
 
* '''Asus'''
 
** KS-631U (comes with Asus Vento KM-63 keyboard/mouse set, not using powered hub) (B)
 
 
* '''Banbridge'''
 
** [http://www.kurpirkti.lt/imagesi/infodb/org_d69dbd9707af8df77eae6e005f681a9a/BANDRIDGE-USB-2X-PS-2-ADAPTER.jpg PS/2 to USB Banbridge CPA4002 Adapter] (B) (Tested with Logitech C-SF17 Cordless Desktop Express)
 
 
* '''BTC - Behavior Tech Computer Corp.'''
 
** Wired Portable Keyboard Model 6100 US (86+9 keys)
 
*** Works with or without a powered hub
 
** Wireless Multimedia Keyboard with build in pointer/mouse Model 9029URF III (86+17 keys) (B)
 
** [http://www.btc.com.tw/english/2-7-07keyboard.htm Wired Multimedia keyboard 6311U/6310U] - rated at 5&nbsp;V/100&nbsp;mA, works directly
 
 
* '''Bush'''
 
** Wired Slimline Keyboard KU-0833
 
*** This does not require a USB hub in order to work with the Raspberry Pi
 
*** In the UK, it is available from Argos for £9.99
 
 
* '''Cerulian'''
 
** Mini wireless keyboard and mouse deskset (B)
 
 
* '''CD Training'''
 
** [http://www.cd-training.fr/?&feed=product&product_id=308 Wireless Combo Keyboard and Mouse (SolClavGlos)]
 
  
* '''Cherry'''
+
This section has been moved to a separate page. See [[RPi USB Keyboards]]
** CyMotion Master Linux (B)
 
** RS 6000 USB ON
 
** G84-4100PTMUS (B) (Compact keyboard. Rated 100&nbsp;mA. Works directly in Raspberry Pi)
 
 
 
* '''Compaq'''
 
** Compaq Internet Keyboard KU-9978 (049f:000e). Rated 5&nbsp;V 100&nbsp;mA. Works directly connected to Raspberry Pi
 
 
 
* '''Das Keyboard'''
 
** Model S Professional Keyboard (Built in USB hub not tested) (B)
 
** Model S Ultimate Keyboard (Built in USB hub working) (B)
 
 
 
* '''Dell'''
 
** SK-8115 (B) (Rated 100&nbsp;mA. Works directly in Raspberry Pi)
 
** L100 (B)
 
** RT7D50 (75&nbsp;mA) (run "sudo dpkg-reconfigure keyboard-configuration")
 
** KB1421 (100&nbsp;mA)
 
** KB2521 (100&nbsp;mA)
 
** KB212-B (Works directly in Raspberry Pi, without powered hub)
 
** 1HF2Y (Works directly in Raspberry Pi)
 
** Bluetooth Wireless Keyboard and Mouse Bundle (B), Bluetooth USB dongle C-UV35 (Rated 500&nbsp;mA, but it works great), Keyboard Y-RAQ-DEL2, Mouse M-RBB-DEL4
 
 
 
* '''Delux'''
 
** K8050
 
 
 
* '''Digicom'''
 
** WKEYPE01 Wireless 2.4&nbsp;GHz Keyboard-mouse Combo, also known as [http://www.riitek.com/product_Info.asp?id=56 Riitek RT-MWK01] and [http://www.verkkokauppa.com/fi/product/52783 Prodige Nanox]
 
 
 
* '''Dynex'''
 
** DX_-WKBD (60&nbsp;mA) (B)
 
** DX_-WKBDSL  (Hot keys not yet tested with Debian) (tested through non-powered 3 dongle USB hub) (B)
 
 
 
* '''EAPPLY'''
 
** EBO-013 Wireless 2.4&nbsp;GHz compact keyboard with touchpad. Rated <40&nbsp;mA works directly from Raspberry Pi. eBay ref 260962010276 from Shenzen, China.
 
 
 
* '''Emprex'''
 
** Wireless Media Control Keyboard With Trackball 9039ARF III (Media functions untested)
 
 
 
* '''Fujitsu Siemens'''
 
** KB SC USB UK (!)
 
** KB910 USB, with led light on the highest level (B)
 
** KB400 USB US
 
 
 
* '''GE'''
 
**  98139 Rev.K1 (Power Keyboard)  (lsusb shows it as "0b38:0010 Gear Head 107-Key Keyboard") - works without a hub (i.e. directly connected) (B)
 
 
 
* '''Gear Head'''
 
** KB3700TP (USB Mini Smart Touch Touchpad Keyboard) (B)
 
** KB3800TP (Wireless Touch Mini Touchpad Keyboard with Smart Touch) (B)
 
*** Works when plugged directly into Raspberry Pi, did not work with powered hub (could be a hub issue)
 
** KB3800TPW (Windows Smart Touch Wireless Keyboard with Touchpad) (B)RASPBMC supported
 
** KB4950TPW (Wireless Touch II Touchpad Keyboard) (B)
 
** KB1500U (USB Mini Keyboard) (B)
 
** KB5150 (2.4&nbsp;GHz wireless keyboard/mouse Combo) (B)
 
*** Works well with a powered hub
 
 
 
* '''Genius'''
 
** Ergomedia 700 (GK-04008/C) used without Hub
 
** KB-06XE (K639) (B)
 
** Slimstar 8000 wireless keyboard
 
 
 
* '''Gigabyte'''
 
** GK-KM7580 2.4&nbsp;GHz Wireless Multimedia Keyboard & Mouse
 
 
 
* '''HP'''
 
** KG-1061
 
** KG-0851 Wireless Keyboard and Mouse
 
** KU-0316 (B)
 
** LV290AA#ABA Wireless Keyboard and Mouse
 
** PR1101U (available from Sainsbury's in the UK, £8, July 2012)
 
** SK-2880
 
 
 
* '''Hyundai'''
 
** HY-K201
 
 
 
* '''iConcepts'''
 
** 2.4&nbsp;GHz Wireless Keyboard and Optical Mouse Model 62550
 
*** (saves a USB port since keyboard and mouse share one transceiver, $14.99 at Fry's Electronics)
 
 
 
* '''Imation'''
 
** KBD-702 Multi-media Wired Keyboard
 
*** (works after the firmware update via [https://github.com/Hexxeh/rpi-update rpi-update] as of 06/27/2012)
 
 
 
* '''IOGEAR'''
 
** IOGEAR GKM561R Wireless HTPC Multimedia Keyboard with Trackball
 
** IOGEAR GKM681R 2.4&nbsp;GHz Wireless Compact Keyboard with Optical Trackball and Scroll Wheel
 
 
 
* '''iPazzPort'''
 
 
 
* '''i.t.works'''
 
** KC04 (direct and by USB hub)
 
** KC Silicone (only tested directly)
 
 
 
* '''Jenkins'''
 
** Jenkins Wireless Desktop Set Blue (B)
 
 
 
* '''KeySonic'''
 
** ACK-540RF (Wireless USB keyboard with built-in trackpad); works fine on Debian Squeeze plugged directly into Raspberry Pi. Also works with Raspbmc with powered hub.
 
** ACK-540RF+ (UK) Wi-Fi keyboard incl. touchpad with USB Wi-Fi dongle works fb with on model B/Raspbian/Wheezy via powered hub
 
** ACK-3700C
 
** ACK-340U+(DE)
 
** ACK-3400U (UK) mini keyboard
 
** ACK-612RF (GER) Wireless Mini-Keyboard; works fine with its wireless adpater plugged directly into Raspberry Pi
 
 
 
* '''Labtec'''
 
** [http://www.labtec.com/index.cfm/gear/details/EUR/EN,crid=28,contentid=692| Ultra-flat Keyboard]
 
 
 
* '''Laptopmate'''
 
** AK-98UNTN7-UBRII Laptopmate RII Touch N7 Mini Wireless Keyboard with touchpad
 
 
 
* '''LC-Power
 
** K1000BMW (lsusb: ID 1241:f767 Belkin; dmesg: HOLTEK Wireless 2.4&nbsp;GHz Trackball Keyboard) tested with Debian 6.0.4
 
 
 
* '''Lenovo'''
 
** SK-8825 UK (B)
 
** Lenovo Enhanced Multimedia Remote with backlit keyboard N5902 (US)
 
** Lenovo Mini Wireless Keyboard N5901 (US)
 
 
 
* '''Lindy'''
 
** 21840 (Wireless RF 2.4&nbsp;GHz Micro Keyboard with built-in optical touchpad/trackpad, USB); works fine on model B/Raspbian/Wheezy - the supplied Lindy USB nano dongle transceiver plugged directly into Raspberry Pi USB port.
 
 
 
* '''Logik'''
 
** Ultra slim keyboard LKBWSL11 (B)  >> '''This is also listed under Problem USB Keyboards?'''
 
 
 
* '''Logitech'''
 
** Comfort Wave 450, labeled 100&nbsp;mA (M/N Y-U0001, P/N 820-001725, PID SC951C40001)
 
** diNovo Mini wireless keyboard with media controls and clickpad 920-000586 (B)
 
** diNovo Edge Keyboard, Windows edition, built-in TouchDisc track-pad, Bluetooth with USB mini-receiver 967685-0403 (B)
 
*** older model 867777-0403 may drop or repeat keys and drop mousepad taps/clicks, works fine with '''dwc_otg.speed=1''' added to cmdline.txt (B)
 
** Wii wireless keyboard KG-0802 (!)
 
** C-BG17-Dual Wireless keyboard and mouse with wired USB receiver (B)
 
** Deluxe 250 Keyboard
 
** Internet 350 (M/N 967740-0403)
 
** Internet Navigator Keyboard
 
** MK120 wired keyboard and mouse
 
** MK220 wireless keyboard and mouse
 
** MK250 wireless keyboard and mouse (no hub needed)
 
** MK260 wireless keyboard and mouse (no hub needed)
 
** MK300 wireless keyboard and mouse
 
** MK320 wireless keyboard and mouse [http://www.amazon.co.uk/Logitech-920-002885-MK320-Wireless-Desktop/dp/B003STDQYW/ref=sr_1_3?ie=UTF8&qid=1339166178&sr=8-3]
 
** MK350 wireless keyboard (using Unifying receiver)
 
** MK520 wireless keyboard and mouse
 
** MK550 wireless keyboard and mouse (B)
 
** MX3200 wireless keyboard and mouse (B)
 
** MX5000 Bluetooth keyboard and mouse (B) The Logitech Bluetooth dongle also does proprietary wireless so it works without Bluetooth drivers.
 
** EX100 Cordless Desktop, Wireless Keyboard and Mouse (B)
 
** EX110 Cordless Desktop, wireless keyboard and mouse (B)
 
** C-SF17 Cordless Desktop Express, Wireless Keyboard and Mouse (B) PS/2 Interface. Tested using [http://www.kurpirkti.lt/imagesi/infodb/org_d69dbd9707af8df77eae6e005f681a9a/BANDRIDGE-USB-2X-PS-2-ADAPTER.jpg PS/2 to USB Banbridge CPA4002 Adapter]
 
** K120 Keyboard (B)
 
** K200 Keyboard (B)
 
** K230 Wireless Keyboard (Unifying receiver, no powered hub) (B)
 
** K340 Wireless Keyboard (Unifying receiver, no powered hub) (B)
 
** K350 Wireless Keyboard (B)
 
** K400 wireless keyboard with touchpad - also listed under "problematic". Works for weeks with openelec and Raspbian without any problems. Worked out of the box - the on/off switch needs to be "on" for it to function correctly. Highly recommended if you are "working from the sofa".
 
** K520 Keyboard (B)
 
** K700 Wireless Keyboard with Touchpad and unifying receiver
 
** K750 Wireless Solar Keyboard (B) (Mac version works too. (B) )
 
** LX 710 - works fine with receiver plugged directly into the Raspberry Pi (accompanying mouse works fine too).
 
** S510 wireless keyboard and mouse (B)
 
** Ultra-Flat Keyboard (M/N Y-BP62A P/N 820-000245 PID SY126UK)labelled 100&nbsp;mA.  OK direct into Model B Raspberry Pi.
 
** G19 Gaming Keyboard, works fine with no external power. Illumination with external power. Powered hum in back of keyboard works too.
 
** G15 Gaming keyboard, as long as you press the backlight button twice to turn off the backlight (it says below it dosen't work with backlight on.
 
** V470 Bluetooth Laser Mouse
 
 
 
''Keyboards and mice also together with Unifying receiver''
 
 
 
* '''Microsoft'''
 
**Microsoft Comfort Curve Keyboard 2000
 
**Microsoft Comfort Curve Keyboard 3000 for Business
 
**Microsoft Digital Media Pro Keyboard Model: 1031 (Debian 13-Apr-2012)
 
**Microsoft Natural Ergonomic Keyboard 4000 (B) (Debian "Wheezy" beta 18-June-2012)
 
**Microsoft Wired Keyboard 600 Model 1366 (Debian 28-May-2012 on Production Model B)
 
**Microsoft Wireless Desktop 700 Keyboard v2.0 (Raspbian Pisces image 08-June-2012 on Production Model B)
 
**Microsoft Wireless Photo Keyboard (Model 1027) Unifying receiver, no hub
 
**Microsoft Wireless Natural Multimedia Keyboard  (Raspbian Pisces 08-July-2012) (B)
 
**Microsoft Windows 2000 Keyboard (KB-USBK110610)
 
**[https://www.microsoft.com/hardware/en-us/p/wired-keyboard-600/ANB-00001 Microsoft Wired Keyboard 600]. The keyboard is rated at 5&nbsp;V/100&nbsp;mA (Wheezy 5-Sept-2012)
 
 
 
* '''Mikomi'''
 
** Wireless Deskset KM80545 Keyboard and mouse (it works, but the range is terrible less than a metre) (B)
 
 
 
* '''Monoprice'''
 
** [http://www.monoprice.com/products/product.asp?c_id=104&cp_id=10404&cs_id=1040401&p_id=6854&seq=1&format=2|Monoprice PS/2 To USB Adapter] Directly and through an unpowered hub with a USB mouse plugged in.
 
 
 
* '''Motorola'''
 
 
 
** Bluetooth wireless ultra slim keyboard and mouse combo (sold as for the "Atrix" phone) work in combination with the Technika Bluetooth adaptor listed below
 
 
 
* '''Novatech'''
 
** [http://www.novatech.co.uk/products/peripherals/desktopkits/nov-wcombo.html|Novatech Wireless Combo - Keyboard & Mouse, Nano adapter] (B)
 
 
 
* '''ONN'''
 
**ONN Keyboard Stock No: ONA11HO089 (from Walmart). Seems to work fine, even without a hub.
 
**ONN Keyboard Stock No: ONA11HO087 (from Walmart). Combination keyboard and mouse package with nano receiver. Be sure to configure keyboard layout.
 
 
 
* '''Ortek'''
 
** Ortek Technology, Inc. [http://www.ortek.com/html/pdt_view.asp?area=46&cat=150&sn=79 WKB-2000S] Wireless Keyboard with Touchpad works fine on Raspbian Wheezy and Raspbmc. Wireless USB receiver (device ID 05a4:2000) is recognised automatically. Connected directly to Raspberry Pi USB port, no powered hub used.
 
 
 
* '''Perixx'''
 
**Periboard 716 Wireless Ultra-Slim Keyboard with Touchpad (Debian 07-Jun-2012 on Production Model B)
 
** PERIBOARD-502 wired keyboard inc built in touchpad (model B/Raspbian Wheezy)
 
** Periduo-707 Plus (Wireless Keyboard and Mouse) works fine ''most'' of the time. Does suffer from dropouts and glitches though. Usual "drawing too much power from USB" problems show up as well - dropped key presses or constant autorepeats. These can be cured by pulling out and reinserting the dongle in the USB socket. The keyboard sometimes hangs after power on when used with my laptop - it seems to need 30 seconds of non-use before it works fine. Again, remove and insert the dongle cures it. Works fine vi my Benq monitor's USB Hub.
 
 
 
* '''Philips'''
 
**Wired Multimedia Keyboard SPK3700BC/97 (Debian 19-Apr-2012 on Production Model B)
 
 
 
* '''Prodige'''
 
**Nanox Wireless 2.4&nbsp;GHz Keyboard-mouse Combo, also known as [http://www.riitek.com/product_Info.asp?id=56 Riitek RT-MWK01] and [http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/WKEYPE01 Digicom WKEYPE01]
 
 
 
* '''Rapoo'''
 
**Rapoo E9080 Wireless Ultra-Slim Keyboard with Touchpad
 
**Rapoo Wireless Multi-media Touchpad Keyboard E2700 [http://www.rapoo.com/showdetails.aspx?P_No=E2700]
 
**Rapoo Ultra-Slim Wireless Multimedia Keyboard and Mouse E9060 (works proper on powered USB Hub)
 
 
 
*'''Riitek'''
 
**RT-MWK03 mini wireless keyboard & trackpad
 
**RT-MWK02+ mini Bluetooth keyboard & trackpad. Followed instructions from this page: [http://www.ctheroux.com/2012/08/a-step-by-step-guide-to-setup-a-bluetooth-keyboard-and-mouse-on-the-raspberry-pi/] and it worked, connection persists across reboots, no problem with either builtin USB or powered USB hub.
 
**RT-MWK01 mini wireless 2.4&nbsp;GHz Keyboard-mouse Combo, also known as [http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/WKEYPE01 Digicom WKEYPE01], and [http://www.verkkokauppa.com/fi/product/52783 Prodige Nanox]
 
 
 
*'''Rosewill'''
 
** RK-200 Standard Keyboard
 
 
 
*'''Saitek'''
 
** Eclipse II Backlit Keyboard PK02AU (B)
 
** Eclipse Backlit Keyboard PZ30AV (B) - works fine when connected directly to Raspberry Pi rev.1 and 2 USB port. No powered hub used.
 
** Expression Keyboard (US)
 
** Cyborg V.5 (B)
 
 
 
*'''SelecLine'''
 
** WK11P & WM11P-SP-PP. Keyboard and mouse set. (B)
 
 
 
*'''SIIG'''
 
** SIIG Wireless Multi-Touchpad Mini Keyboard 02-1286A v1.0 (B)
 
 
 
*'''Silvercrest'''
 
** MTS2219 Wireless Keyboard and mouse set. Powered hub NOT used. (B)
 
 
 
*'''SolidTek'''
 
** Solid Tek KB-P3100BU ASK-3100U. 
 
 
 
*'''Sony'''
 
** Keyboard for PlayStation 2 (PS2) Linux. Works without powered hub with 5&nbsp;V 1&nbsp;A supply, requires manual keyboard remapping with Debian Squeeze to USA 101-key layout.
 
 
 
* '''SteelSeries'''
 
** Merc keyboard (B)
 
 
 
* '''Sun Microsystems'''
 
** Model: Type 7, SUN PN: 320-1348-02 (Danish key layout)
 
** Model: Type 6, SUN PN: 320-1279-01 (Danish key layout)
 
 
 
* '''Sweex'''
 
** [http://www.sweex.com/en/assortiment/input/keyboards/KB060UK/ KB060UK] Wired Multimedia Keyboard
 
 
 
* '''Technika'''
 
** WKEY03 (B)
 
** TKD-211
 
 
 
* '''Tesco'''
 
** Value Keyboard VK109 (B)
 
** Multimedia K211 Wired Keyboard (B)
 
 
 
*'''The Pi Hut'''
 
** Super Slim Apple Style Keyboard (from [http://thepihut.com/products/usb-keyboard-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
** Super Slim Apple Style Keyboard Set (Keyboard & Mouse) (from [http://thepihut.com/products/usb-keyboard-mouse-bundle-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
 
 
* '''Trust'''
 
** Trust 17916 Compact Wireless Entertainment Keyboard http://www.trust.com/products/product.aspx?artnr=17916 (B)
 
** Trust ClassicLine Keyboard http://trust.com/17184
 
** Trust Camiva MultiMedia Keyboard http://trust.com/products/product.aspx?artnr=16087
 
** Trust Convex Keyboard http://trust.com/products/product.aspx?artnr=17603 tested Debian 6-19-04-2012 and archlinuxarm-13-06-2012 (B)
 
 
 
* '''Unbranded'''
 
** AK-601 Wireless Mini Keyboard and Trackball (with laser pointer) - sourced from eBay Chinese seller
 
 
 
* '''Unicomp'''
 
** USB Endurapro - keyboard and trackpoint work perfectly from powered hub
 
 
 
* '''Q-Connect'''
 
** AK-808 (B)
 
 
 
* '''Xenta'''
 
** 2.4&nbsp;GHz Wireless Multimedia Entertainment Keyboard with Touchpad (B)
 
** Mini Multimedia Keyboard (Model no.: 808M) (B)
 
 
 
===Problem USB Keyboards===
 
 
 
Note that generally PS/2 keyboards with an USB adapter will not work directly on a Raspberry Pi port, due to the fact that PS/2 keyboards are designed for normal 5&nbsp;V +-5% range, while USB keyboards must be designed to work with 4.4 Volt, and generally USB devices on the Raspberry Pi may receive less than 4.75 Volt. PS/2 + USB adapter keyboards might work behind a powered hub, which does provide the full 5.0&nbsp;V. Some of these keyboards work when running the latest Raspbian, but not when using the overclocked XBMC version of Raspbmc, probably due to the overclocking drawing more power away from the rest of the support system devices.
 
 
 
* '''A4 Tech'''
 
** Model GL-6 USB Keyboard, 20&nbsp;mA. Part of wireless keyboard/mouse bundle GL-6630 (GL-6 + G7-630 + RN-10B) - suffers from USB flakeyness. Even on a powered hub. No problems on other computers I have tested it with.
 
* '''Accuratus'''
 
** Accuratus KYBAC100-101USBBLK causes kernel panic (rated 100&nbsp;mA). Tested with 1000&nbsp;mA cheap unbranded and Nokia 1200&nbsp;mA power adaptors.
 
* '''Apple'''
 
** [http://www.powerbookmedic.com/xcart1/images/D/apple-keyboard.jpg Apple Keyboard (109 keys) A1048]. Draws too much power and does not seem to work properly when plugged into a powered hub.
 
*'''Argos'''
 
** Argos Value Wired Keyboard causes kernel panic
 
* '''Choidy'''
 
** Identifiers from usb-devices: Vendor=1a2c ProdID=0002 Rev=01.10 Product=USB Keykoard (yes, 'Keykoard') causes kernel panic
 
* '''Cit'''
 
** KB-1807UB Causes kernel panic (rated <200&nbsp;mA)
 
* '''Dell'''
 
** SK-8135 (B) (Rated 1.5&nbsp;A. Takes too much power from Raspberry Pi even when not used as USB hub. Symptom = repeated keystrokes)
 
** SK-8115 causes kernel panic (rated 100&nbsp;mA) Debian 6-19-04-2012 (B)
 
** Y-U0003-DEL5 Sticky / Non-responsive keys
 
* '''Gear Head'''
 
** KB2300U - Causes kernel panic (B)
 
* '''GMYLE'''
 
** Wired USB Slim Chocolate Multimedia Media Typing Keyboard With 3 USB Port hub (B) - Kernel Panic on startup if plugged in.  If plugged in at login prompt then freeze. [http://www.amazon.co.uk/gp/product/B0067EC3GW/]
 
* '''Inland'''
 
** Inland USB Keyboard Model #70010
 
* '''Jeway'''
 
** JK-8170 "The Hunter" - causes kernel oops (Debian6-19-04-2012) (B)
 
* '''Labtec'''
 
** ultra-flat wireless desktop USB - Keyboard has 'sticky' keys. Tested both debian6-19-04-2012 and archlinuxarm-13-06-2012 (B)
 
* '''Logik'''
 
** Wired Multimedia Keyboard Model: LKBWMM11 - causes kernel panic (on Debian 190412 distro) (B)
 
** Wired Ultra Slim Keyboard Model: LKBWSL11 - causes USB power issues. Not reliable. Causes other USB devices to fail (B) >> '''This is also listed under Working USB Keyboards??'''
 
* '''Logitech'''
 
** Logitech Illuminated Keyboard (unstable; not working with led light on; tested both US and NO layouts with both Apple iPad 2 and Asus TF-101 USB chargers)
 
** G110 Gaming Keyboard - only works with illumination off, otherwise unresponsive. Once failed it needs reconnecting before another attempt. (B)
 
** G15 Gaming Keyboard - LCD and key backlights flicker, 95% unresponsive to typing. I don't know of a way to turn the illumination off. (B)
 
** K360 Wireless Keyboard - Occasional sticky keys. (B)
 
** K400 wireless keyboard with touchpad (completely non-functional on debian6-19-04-2012)
 
** G510 Gaming Keyboard - lagging or unresponsive keys.
 
** MX5500 wireless keyboard and mouse with USB Bluetooth reciever - Unstable, looses connection without prior notice
 
** EX100 Cordless Desktop, wireless keyboard and mouse. Mouse and keyboard hangs every few minutes (with or without hub).
 
* '''Microsoft'''
 
** Wireless Desktop 800 - Keyboard has 'sticky' keys. (B)
 
** Wireless Entertainment Keyboard - No key input recognized (possibly connectivity issue as pairing devices does not seem to work)
 
** Wireless Optical Desktop 1000 - Keyboard has 'sticky' keys (B)
 
** Wireless Keyboard 2000 - Keyboard has 'sticky' keys. (B)
 
** Wireless Desktop 3000 - Keyboard has 'sticky' keys.
 
** Arc wireless - Keyboard has 'sticky' keys. (B)
 
** Sidewinder X4 - Keyboard has 'sticky' keys. (B)
 
** Sidewinder X6 - Keyboard has 'sticky' keys. (B)
 
** Wireless Comfort Keyboard 5000 - Keyboard has 'sticky' keys. (B)
 
** Razer Reclusa - Keyboard has 'sticky' keys. (B rev 2.0)
 
* '''Novatech'''
 
**  NOV-KEY2 - Causes kernel panic (B)<ref>http://www.raspberrypi.org/forum/troubleshooting/keyboard-creates-kernal-panic/page-2</ref>
 
* '''PC World Essentials'''
 
** PKBW11 Wired Keyboard - no power to keyboard, no error messages on both Arch 29-04-2012 and Debian6-19-04-2012, the same Raspberry Pi works with Asda keyboard. Me too, but it caused a kernel panic -- tested on powered hub and direct.
 
* '''Razer'''
 
** Razer Tarantula gaming keyboard - sticky keys, could be power issue as is programmable with host powered USB hub and audio jacks.
 
** Razer BlackWidow - Sticky keys, could be a power related issue due to illuminated logo (Blue LED).
 
** Razer Arctosa - Sticky keys, most probably power related issue since it states it's rated at 5&nbsp;V 500&nbsp;mA. (B)
 
* '''SIIG'''
 
** Wireless Ultra Slim Multimedia Mini Keyboard JK-WR0612-S1 - Unresponsive and sticky keys.
 
* '''Texet'''
 
** MB-768B standard keyboard (Rated 5&nbsp;V 1.5&nbsp;A (!), so probably too much power drain. Kernel panic, Debian6-19-04-2012)
 
* '''Trust'''
 
** TRUST GXT 18 Gaming Keyboard - No power to keyboard, could be a driver issue - no error messages.
 
* '''Unbranded'''
 
** Compuparts
 
** model no. HK-6106 (B) <ref>http://www.raspberrypi.org/forum/troubleshooting/keyboard-creates-kernal-panic/page-2</ref>
 
** LK-890 (Multimedia keyboard & Optical Mouse) - kernel panic on Debian Squeeze, ArchLinux and Qtonpi.
 
* '''Verbatim'''
 
** [http://www.amazon.com/gp/product/B004LB5AKY/ref=oh_details_o00_s00_i02|Verbatim 97472 Mini Wireless Slim Keyboard and Mouse] -  Keyboard has lagging, unresponsive and sticky keys issues.  (Tested with and without powered USB hub.)
 
* '''Wilkinsons / TEXET'''
 
** Model MB-768B causes kernel panic on debian6-19-04-2012.
 
* '''Xenta'''
 
** HK-6106 - causes kernel panic (on Debian 190412 distro)(B)
 
** Multimedia Wireless Keyboard and Mouse Set (Keyboard Model: HK3518B + Mouse Model HM3301) (B) - occasional sticky keys, and occasional complete lock-up
 
  
 
== USB Mouse devices ==
 
== USB Mouse devices ==
USB mouse devices that present themselves as a standard HID (Human Interface Device) device should work, however some hardware requires special drivers or additional software, usually only compatible with Windows operating systems. 
 
 
===Working USB Mouse Devices===
 
The following is a list of specific mouse devices known to work and which appear to be fault-free.
 
  
* '''A4Tech'''
+
This section has been moved to a separate page. See [[RPi USB Mouse devices]]
** OP-530NU Padless Wired Mouse
 
 
 
* '''Asda'''
 
** HM5058 (Smart Price) Wired Mouse
 
** Wireless Multimedia Deskset (keyboard, mouse and USB dongle) Model: HKM8016B (Note: Shown on Asda Website as HK8016B) (B)
 
 
 
* '''ASUS'''
 
** MS-511U (comes with Asus Vento KM-63 keyboard/mouse combo) (B)
 
** MG-0919 (wireless)
 
 
 
* '''Belkin'''
 
** F8E882-OPT (B)
 
 
 
* '''Cerulian Technology'''
 
** 3 Button Mini Mobile Blue Trace Mice - Model:N96JA
 
 
 
* '''Dell'''
 
** M-UVDEL1 (B)
 
** MOC5UO (100&nbsp;mA)
 
** M056U0A (B)
 
** DZL-MS111-L (B) (100&nbsp;mA)
 
** MS-111P (100&nbsp;mA)
 
** Bluetooth Wireless Keyboard and Mouse Bundle (B), Bluetooth USB dongle C-UV35 (Rated 500&nbsp;mA, but it works great), Keyboard Y-RAQ-DEL2, Mouse M-RBB-DEL4
 
 
 
* '''Dynex'''
 
** DX-WMSE (100&nbsp;mA) (B)
 
 
 
* '''Fellowes'''
 
** 99928 USB Micro Track Ball (works without a hub, directly plugged in) (B)
 
 
 
* '''Filand'''
 
** OP-102i Mini Optical Mouse
 
 
 
* '''Genius'''
 
** GM-04003A (B)
 
** Slimstar 8000 wireless mouse (Can be intermitent. Mouse pointer sometimes is irratic.)
 
** Traveler 515 Laser
 
 
 
* '''HP'''
 
** MN-UAE96 (The basic stock HP wired mouse)(B)
 
 
 
* '''iConcepts'''
 
** 2.4&nbsp;GHz Wireless Keyboard and Optical Mouse Model 62550
 
*** (saves a USB port since keyboard and mouse share one transceiver, $14.99 at Fry's Electronics)
 
 
 
* '''Jenkins'''
 
** Jenkins Wireless Desktop Set Blue (B)
 
 
 
* '''Kensington'''
 
** Kensington Expert Mouse Trackball K64325
 
** Kensington Expert Mouse "Slimblade" K72327US
 
 
 
* '''Labtec'''
 
** Corded Laser Glow Mouse 1600, rated 5&nbsp;V 100&nbsp;mA (P/N 810-000819, M/N M-UAZ149, PID GT83401)
 
 
 
* '''Lenovo'''
 
** Wired Optical Mouse Model: MO28UOL
 
 
 
* '''Logik'''
 
** Wired Optical Glow Mouse Model: LGGMO10. (B)
 
 
 
* '''Logitech'''
 
** B105 Mouse for Laptops (OEM)
 
** Cordless Pilot Optical Mouse M/N M-RR95 with Cordless Mouse Receiver M/N C-BA4-MSE
 
** G5 Logitech Gaming Mouse (B)
 
** G5v2 Logitech Gaming Mouse (B)
 
** G500 Logitech Gaming Mouse (B)
 
** G700 Logitech Wireless Gaming Mouse (B)
 
** LX-700 Cordless Desktop Receiver (B)
 
** LX 710 Wireless Mouse - works fine with receiver plugged directly into Raspberry Pi (accompanying keyboard works fine too).
 
** M90 optical mouse
 
** M185 Wireless Mouse (B)
 
** M210 (part of the MK260 set) (B)
 
** M305 Wireless Mouse
 
** M310 Cordless Mouse
 
** M325 Wireless Mouse
 
** M505 USB wireless laser, model no: 910-001324 (B)
 
** M510 Wireless Mouse (B)
 
** M705 Marathon Mouse (Unifying receiver, no powered hub) (B)
 
** M-BD58 Wheel Mouse (B)
 
** M-BJ58/M-BJ69 Optical Wheel Mouse (B)
 
** M-BJ79 (B)
 
** M-BT96a Optical Mouse
 
** MX320/MX400 laser mouse (B)
 
** MX518 Optical wheel mouse (B)
 
** Optical USB Mouse (M/N 931643-0403)
 
** Performance Mouse MX (B)
 
** MX Revolution (B) (Debian "Wheezy" beta 18-June-2012)
 
** VX Nano Cordless Laser Mouse for Notebooks
 
** Wheel Mouse (M/N BJ58)
 
 
 
* '''Medion'''
 
** Mini mouse Model M101-CBJ P/N 40016632 S/N 7BFSA00003445 rated 5&nbsp;V 100&nbsp;mA. Works fb on model B with Raspbian Wheezy
 
 
 
* '''Microsoft'''
 
** Comfort Curve Mouse 3000 for Business
 
** Comfort Mouse 6000 (works when directly connected to Raspberry Pi (B).  Does not work when connected through USB Hub (mouse pointer intermittent).
 
** Compact optical mouse 500 V2.0 (B)
 
** Wheel Optical Mouse (wheel and additional buttons not tested) (B)
 
** Microsoft Intellimouse Optical Mouse
 
** Microsoft Wireless Laser Mouse 8000
 
** Microsoft Wireless Mobile Mouse 1000
 
** Microsoft Wireless Mobile Mouse 3500
 
** Microsoft Wireless Mobile Mouse 4000
 
** Microsoft Wireless Mouse 700 v2.0
 
** Microsoft Comfort Mouse 4500
 
** Wireless IntelliMouse Explorer 2.0 (unifying receiver, no hub)
 
 
 
* '''Novatech'''
 
** [http://www.novatech.co.uk/products/peripherals/miceandtrackballs/nov-mouser.html|Novatech M1 USB Mouse - Wired](B)
 
** [http://www.novatech.co.uk/products/peripherals/miceandtrackballs/nov-dl10.html|Novatech DL10 Wireless Mouse] (B)
 
 
 
* '''Perixx'''
 
** PERIMICE-210 U Red (Part No.R1J)
 
 
 
* '''Razer'''
 
** Boomslang Collectors Edition 2007 (B)
 
 
 
* '''Rosewill'''
 
** Rosewill RM-C2U
 
 
 
* '''Saitek'''
 
** Notebook Optical Mouse (PM46)
 
 
 
* '''Samsung'''
 
** Samsung model:AA-SM3PCPB USB Optical Mouse (draws 50&nbsp;mA)
 
 
 
* '''Sun microsystems'''
 
** Model: FID-638 , SunPN: 371-0788-01
 
 
 
* '''Sweex'''
 
** [http://www.sweex.com/en/assortiment/input/optical-mice/MI015/ MI015]
 
 
 
* '''Swiftpoint'''
 
** [http://http://www.americas.futuremouse.com/] Swiftpoint Mini Wireless Optical Mouse. Does not require any special drivers. Haven't confirmed if charging the mouse requires a powered USB hub or not.
 
 
 
* '''Targus'''
 
** AMU2701EUK (B)
 
 
 
* '''Technika'''
 
** TKOPTM2 (B)
 
**TKD-211
 
**TKNM110
 
 
 
* '''Tesco'''
 
** Wired optical mouse M211 (B)
 
 
 
*'''The Pi Hut'''
 
** USB Mouse for Raspberry Pi (from [http://thepihut.com/products/usb-mouse-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
** Super Slim Keyboard & Mouse Set (from [http://thepihut.com/products/usb-keyboard-mouse-bundle-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
 
 
* '''Trust'''
 
** Trust Nanou Wireless Micro Mouse http://trust.com/products/product.aspx?artnr=17087
 
 
 
* '''Verbatiam'''
 
**Mini Nano Optical Mouse 97470 (wireless on non-powered three USB dongle hub) (B)
 
 
 
* '''Xenta'''
 
** MOW0810 (B)
 
** Wired Optical Mouse (from [http://thepihut.com/products/usb-mouse-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
 
 
* '''Generic'''
 
** Generic 2.4&nbsp;GHz Wireless Mouse (ID 040b:2013 Weltrend Semiconductor) (B)
 
 
 
===Problem USB Mouse Devices===
 
The following is a list of specific mouse devices that have problems working with the Raspberry Pi
 
* '''A4Tech'''
 
** Model G7-630 Wireless Mouse, 20&nbsp;mA. Part of wireless keyboard/mouse bundle GL-6630 (GL-6 + G7-630 + RN-10B) - suffers from USB flakeyness. Even on a powered hub. No problems on other computers I have tested it with.
 
* '''HP'''
 
** HP Retractable Mobile Mouse (Optical) HP Product Number XP472AA - errors / boot loop RASPBMC (B)removed mouse, started with no further errors. 
 
 
 
* '''Logik'''
 
** Logik IMF Blue Trace Wired USB mouse (Model LMWBLU11) - disconnects from the USB port every 20 seconds when using the Raspian distro. Always reconnects to the USB port successfully (B)
 
 
 
* '''Logitech'''
 
** Logitech G400 Gaming Mouse - 100% CPU load and laggy mouse cursor when the mouse is moved. MX518 works fine on the same setup, so I suspect it's a polling rate issue. [http://tech2.in.com/reviews/mice/logitech-g400-is-it-a-worthy-successor/231012 this] says the mouse is 1000&nbsp;Hz out of the box, whereas the 518 is only 125&nbsp;Hz. Solution found: add usbhid.mousepoll=8 to the kernel commandline.
 
 
 
* '''Microsoft'''
 
** Microsoft Touch Mouse - Does not see right clicks, Only left.
 
 
 
* '''Razer'''
 
** Naga Wired USB mouse - the mouse seems to present itself as a keyboard because the numpad on the left-hand side of the device works, but the cursor doesn't move.
 
 
 
* '''Roccat'''
 
** Kone[+] Wired USB mouse - Nothing happens when moving the mouse, haven't looked further into the issue (B)
 
 
 
* '''Trust'''
 
** Optical USB Mouse MI-2250 - Nothing happens when moving the mouse (B)
 
 
 
* '''Xenta'''
 
** Multimedia Wireless Keyboard and Mouse Set (Mouse Model: HM-3301) (B) - frequent lost connection giving stuttering mouse cursor indicating USB current not enough for dongle
 
  
 
== USB Real Time Clocks ==
 
== USB Real Time Clocks ==
Line 1,169: Line 76:
 
Does not require a powered hub.
 
Does not require a powered hub.
  
== USB Wi-Fi Adapters ==
+
==Internet==
 +
=== USB Wi-Fi Adapters ===
 +
This section has been moved to a separate page. See [[RPi USB Wi-Fi Adapters]]
  
See also: http://www.element14.com/community/docs/DOC-44703/l/raspberry-pi-wifi-adapter-testing
+
=== USB Bluetooth adapters ===
 +
This section has been moved to a separate page. See [[RPi USB Bluetooth adapters]]
  
There is a howto on installing the TL-WN722N adapter [http://elinux.org/RPi_Peripherals#Wireless:_TP-Link_TL-WN722N_USB_wireless_adapter_.28Debian_6.29 here], which also acts as a guide for installing others too.
+
=== USB Ethernet adapters ===
 +
This section has been moved to a separate page. See [[RPi USB Ethernet adapters]]
  
===Working USB Wi-Fi Adapters===
+
=== USB 3G Dongles ===
 +
==== Huawei ====
 +
* E1750 [https://shkspr.mobi/blog/2012/07/3g-internet-on-raspberry-pi-success installation instructions]
 +
* E173
 +
* E1820 Works on Raspbian with Sakis3G
 +
* E220 [http://raspberry-at-home.com/installing-3g-modem/ installation instructions]
 +
* E353 HiLink Works on Raspbian
 +
* E160 (AT commands only)
 +
* E169, E620, E800, (12d1:1001) - works on Raspbian Wheezy, [https://github.com/sk-vpohybe/stopa-monitor/wiki/3G-modem-Huawei-E169-E620-E800 details here]
 +
* E303 - works with Raspbian Wheezy 2015-02-16 out of the box, will be recognized as network-adapter [ethX]. usb_modeswitch may be used to configure it as a serial modem, so that tools like sakis3g (mobile connection) and gammu (SMS) have a better control over it (note: be sure to download a version of Gammu newer than 1.37.0 so that it is fully supported)
  
These adapters are known to work on the Raspberry Pi. This list is not exhaustive, other adapters may well work, but it has not yet been tried.
+
==== Sierra Wireless ====
 +
* AirCard 250u works with wvdial/network manager
 +
* AirCard 320u (0f3d:68aa) works in WWAN mode, driver provided by the kernel. Tested on Arch.
 +
** Kernel version 3.10 has a bug that causes the WWAN interface to never be in ''RUNNING'' state (no carrier). Use 3.6 kernel instead.
 +
** AT command guide can be found [http://mycusthelpadmin.net/SIERRAWIRELESS/_cs/AnswerDetail.aspx?aid=44 here]
 +
** for GPS to work you have to enable it. First, setup the modem (guide [http://whirlpool.net.au/wiki/hw_model_1210 here]) and after that enable NMEA output by passing ''nmea=1'' parameter to the ''sierra'' kernel module. '''Warning! Enabling NMEA output may cause the modem to drop connections / restart itself'''. This is probably related to higher power drain. This may not be the issue when a powered hub is used.
 +
* 307 Works fine with Sakis3G script. The connection LED does not change its state after establishing a connection but the same behaviour on a normal linux system.
 +
* AirCard 340u (Netgear/ATT Beam) works with latest GobiNet/GobiSerial code on Raspbian and 3.10.25+ kernel. Requires firmware update from Netgear to disable Windows 8 support and make it autoconnect. [http://wes.skeweredrook.com/raspberry-pi-att-beam/ guide here].
  
'''Note:''' A Wi-Fi adapter will probably need more power than the Raspberry Pi USB port can provide, especially if
+
==== ZTE ====
there is a large distance from the Wi-Fi adapter to the Wi-Fi Access Point. Therefore, you may need to plug the Wi-Fi adapter into a powered USB hub.
+
* ZTE MF190S
 +
* ZTE MF626 <br>Works fine with Sakis3G script. You can use force it to ALWAYS be in modem mode (See here: http://forums.whirlpool.net.au/archive/1205127 ), or use usb-modeswitch ( as described here http://blog.christophersmart.com/2009/05/21/telstra-nextg-working-with-mf626-usb-modem/ )
 +
* ZTE MF628 Tested with Sakis3g using --noprobegsm, use usb_modeswitch to get ID 19d2:0031.
 +
* ZTE MF70 (Telstra 3G USB + Wi-FI) Tested. Automatically appears as ethernet device. No usb_modeswitch required. Use DHCP to acquire IP address/DNS/Gateway etc. To configure modem, use web browser and visit http://192.168.0.1/
 +
*ZTE Rocket MF591 - Tested with T-mobile network and Model B+ running Raspbian with usb-modeswitch and Sakis3G script. (Followed guide to work: http://www.instructables.com/id/Raspberry-Pi-as-a-3g-Huawei-E303-wireless-Edima/?ALLSTEPS)
  
* '''3COM'''
+
==== Others ====
** 3CRUSB10075: ZyDAS zd1211rw chipset (!)
+
* Franklin U600 from Sprint / VirginMobile
 
+
** Use usb_modeswitch and vendor 0x1fac and product 0x0150/0x0151
* '''7DayShop'''
+
* Digicom Internet Key 7.2 HSUPA '''MU372-L01''' [http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/MU372L01]
** W-3S01BLK, W-3S01BLKTWIN: Unbranded product available from 7DayShop, in a single or twin pack. [http://www.7dayshop.com/catalog/product_info.php?cPath=777_9&products_id=112046], [http://www.7dayshop.com/catalog/product_info.php?&products_id=112527]. Tested on Debian Wheezy, with the dongle attached directly to the Raspberry Pi along with the wireless keyboard receiver. Shows up as a Ralink RT5370 device, and no drivers or additional software downloads required. Created wpa.conf, edited 'interfaces' file and restarted the networking. The manufacturer portion of the MAC address (7cdd90) is assigned to "Shenzhen Ogemray Technology Co., Ltd."
+
Tested on Raspbian and Archlinux. Detected as 230d:0001. Works with cdc_acm driver. Install usb_modeswitch.
** It works without additional software connected directly to a Rev 2 Raspberry Pi, but it stops working after a period of time (3 to 4 hours) with a fully updated Wheezy and all the 'USB workarounds' [http://elinux.org/Rpi_USB_check-list] in place.
+
There are 2 "com ports"( /dev/ttyACM0 and /dev/ttyACM1 ) . Tested with Network Manager.Works also perfectly with SAKYS3G [http://www.sakis3g.org/] tools  (!! led is always off !!) and wvdial. A working wvdial.conf: http://ubuntuforums.org/showpost.php?p=10361881&postcount=28  . (for example for Vodafone IT , replace Init3 with this: Init3 = AT+CGDCONT=1,"IP","web.omnitel.it"  and replace line Modem = /dev/ttyUSB0 with Modem = /dev/ttyACM1 and run with   wvdial voda .
 
+
* Vodafone MD950 (1dbc:0005) - is working on RPi (Raspbian Wheezy) but not out of the box, [https://github.com/sk-vpohybe/stopa-monitor/wiki/3G-modem-Vodafone-MD950 more details here].
* '''Alfa'''
 
** AWUS036NEH: Tested on Debian Squeeze (with Ralink firmware package)
 
** AWUS036NH: Tested on Arch Linux ARM using the rt2800usb module.
 
** AWUS036NH: Tested on Debian Wheezy (with Ralink firmware package). Tested on Raspbian too (drivers from aircrack-ng).
 
** AWUS036H (500&nbsp;mW version): Tested on Raspbian (drivers from aircrack-ng).
 
** AWUS036H (1&nbsp;W version): Tested on Raspbian (drivers from aircrack-ng). Needs USB powered HUB or Rev2 of the board / polyfuse bypass.
 
** AWUS036NHA: Tested on Raspbian (drivers from aircrack-ng). Works fine if connected after boot, otherwise Raspberry Pi won't boot up.
 
 
 
* '''AirLink101'''
 
** AWLL5088: Tested on Debian Wheezy. This adapter is based on the OEM Edimax EW-7811Un.  For automatic installation, See MrEngmanns script listed below under the Edimax device.
 
 
 
* '''Asus'''
 
** [http://www.element14.com/community/docs/DOC-44703 USB-N10] USB ID 0b05:1786, r8712u staging driver, included on Fedora Remix & Arch, must [http://www.element14.com/community/servlet/JiveServlet/download/44948-8-97488/r8712u_ko.zip download] for Debian and install firmware - Realtek from non-free Squeeze repository (B) (not needed with latest Raspbian “Wheezy” 2012-07-15: this Asus works N10 out of the box) Does not support nl80211 APIS, so hostapd won't work.
 
** [http://www.element14.com/community/docs/DOC-44703 USB-N13] USB ID 0b05:17ab, works with [http://learn.adafruit.com/adafruit-raspberry-pi-educational-linux-distro/occidentalis-v0-dot-1 Adafruit Occidentalis v0.1 image] as it includes kernel [http://www.element14.com/community/message/57635#57660 with 8192u driver built-in] (B)
 
** WL-167G v1 USB ID 0b05:1706, Ralink RT2571 working out-of-the-box on Debian image from 2012-04-19. Requires powered hub, otherwise it is detected by OS, but it will not function.
 
** WL-167G v3 USB ID 0b05:1791, working out-of-the-box on Linux raspberrypi 3.2.27+ #160 PREEMPT Mon Sep 17. Does not require powered hub.
 
 
 
* '''AusPi Technologies'''
 
** AusPi Wireless Adapter [Realtek RTL8188S]. Works without a powered HUB. Tested on OpenELEC (works OOB), RaspBMC (works OOB), XBian (works OOB) and 2012-08-08 Raspbian Wheezy (works OOB). Distributed in Australia by [http://www.buyraspberrypi.com.au/raspberry-pi-802-11bgn-usb-wireless-dongle/ Buy Raspberry Pi Australia].
 
 
 
* '''Belkin'''
 
** Belkin Components F5D7050 Wireless G Adapter v3000 [Ralink RT2571W]. On Debian requires the firmware-ralink package from the non-free repository. The usbcore module needs to be added to /etc/modules [http://www.penguintutor.com/blog/viewblog.php?blog=6281 install instructions].
 
** Belkin Components F5D8053 ver.6001 Wireless N Adapter [Realtek RTL8188SU]. Tested on OpenELEC (works OOB), RaspBMC (works OOB), Raspian - 2012-07-15-Wheezy-raspbian (followed [http://forum.xbian.org/viewtopic.php?f=7&t=29 instructions here]) '''Powered hub required!'''
 
** Belkin Components F5D8053 ver.6001 Wireless N Adapter [Realtek RTL8188SU]. Works on RaspBMC OOB (with NetworkManager plugin). Works WITHOUT powered hub on 5&nbsp;V 800&nbsp;mA power with 6 overvolt (nothing else connected to USB)
 
** Belkin Components F7D1101 v1 Basic Wireless Adapter [Realtek RTL8188SU] USB ID 050d:945a, r8712u staging driver, included on Fedora Remix & Arch, must [http://www.element14.com/community/servlet/JiveServlet/download/44948-8-97488/r8712u_ko.zip download] for Debian and install firmware - Realtek from non-free Squeeze repository (B)
 
**Belkin Components F6D4050 V1 [Realtek RT3070] USB ID: 050d:935a Driver: RT3572STA(recommended),RT2800USB,RT2870STA. Tested under Arch using [https://wiki.archlinux.org/index.php/Setting_Up_Belkin_F6D4050_Wireless_USB_Dongles this] guide.
 
**Belkin Components F6D4050 V1/V2 [Realtek RT3070] USB ID: 050d:935a / 935b Driver: RT3572STA.  Tested with Raspbian - See [http://iggy82.blogspot.co.uk/2012/08/wireless-n-raspberry-pi-belkin-f6d4050.html installation instructions] - Powered hub not required!
 
** Belkin Components F7D2102 "N300" Micro Wireless USB adapter. Tested with Occidentalis 0.1. Tested and working on Rasbian Wheezy (and RaspBMC), driver RTL8192CU, no powered hub needed (dongle directly attached to the onboard ports)
 
** Belkin Components F9L1001v1 "N150" Wireless USB Adapter. Tested and working on Rasbian Wheezy WITHOUT powered hub.
 
** Belkin Surf Micro WLAN USB-Adapter (Raspbian Wheezy, unpowered hub, "N150")
 
 
 
* '''BlueProton'''
 
** [http://www.element14.com/community/docs/DOC-44703 BT3] USB ID: 0bda:8187; tested on Debian, Fedora & Arch; rtl8187 driver (B)
 
 
 
* '''Buffalo'''
 
** USB ID: 0411:01A2 WLI-UC-GNM - Tested on Raspbmc; rt2800usb driver
 
 
 
* '''Conceptronic'''
 
** C300RU. Works out of the box in Raspbian. Causes reboot when plugging on a live Rev. 2 Raspberry Pi
 
 
 
* '''Conrad'''
 
** WLAN Stick N150 mini. Works out of the box in OpenELEC, [http://www.t3node.com/blog/sempre-wireless-usb-stick-wu300-2-on-raspberry-pi/ requires firmware - Realtek and r8712u kernel module on Debian].
 
** WLAN Stick N150 Nano [Realtek RTL8188CUS]. Requires a powered USB hub. See Micronet SP907NS for installation instructions and script.
 
 
 
* '''DELL'''
 
**  Wireless 1450 [Intersil ISL3887]. Works out of the box, but it requires a powered hub (the Raspberry Pi boots with this dongle plugged in, recognizes and configures it, works for some time, but then it crashes randomly under heavy traffic. A powered hub seems to fix the issue).
 
 
 
* '''DIGICOM'''
 
**  USBWAVE54    [chipset Zydas ZD1211] . [[http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/UsbWave54]] Works out of the box in OpenELEC. With Raspbian or Debian squeezy/Wheezy works with zd1211-firmware .
 
**  USBWAVE300C  [chipset Ralink 2870] . [[http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/UsbWave300c]] Works out of the box in OpenELEC. With Raspbian or Debian squeezy/Wheezy works with firmware-ralink .
 
 
 
* '''D-Link'''
 
** AirPlus G DWL-G122 (rev. E). USB ID 07d1:3c0f, Ralink RT2870. On Debian requires the <code>firmware-ralink</code> package from the <code>Squeeze-firmware</code> non-free repository. (However I experience total crashes on Raspbian 2012-07-15 after a few minutes of load on the WLAN. Will have to investigate via serial console.)
 
** AirPlus G DWL-G122 (rev. C). USB ID 07d1:3c03, Ralink RT2571. Working out-of-the-box on Arch image from 2012-04-29.
 
** AirPlus G DWL-G122 (rev. B1). USB ID 2001:3c00, Ralink RT2571. Working out-of-the-box on Arch image from 2012-06-13.
 
** DWA-110 (Version A1). Requires the ralink package from the non-free repository on Debian.
 
** DWA-121 (Version A1). Wireless N 150 Pico. Works out-of-the-box with Raspian Wheezy (2012-09-18) and Raspbmc (2012-11-06) using Network-Manager addon (see Program - Addons)
 
** DWA-123 (Version A1). USB ID 2001:3c17, Ralink RT2800. Working out-of-the-box on Arch image from 2012-04-29. (working without UBS Hub - not yet sure if it achieves full speed though.)
 
** DWA-131 USB ID 07d1:3303,Realtek RTL8192SU, 802.11n Wireless N Nano.  Works out of the box on Raspbian “Wheezy”. Verified with direct USB: no powered USB hub needed. Also verified when Nano used in powered USB hub. Someone had trouble configuring SSID/Passphrase in etc/network/interfaces file. But no problem & very easy to configure using wicd: wicd is a gui interface on LXDE for network configuration. Install it using command-line: <code>apt-get install wicd</code>. Once configured ith wicd to auto-run on boot, no need to turn back to LXDE. Recommended.
 
** DWA-140 (Version B1). USB ID 07d1:3c09, Ralink RT2870. On Debian requires the <code>firmware-ralink</code> package from the <code>Squeeze-firmware</code> non-free repository.
 
** DWA-140 (Version B2). USB ID 07d1:3c0a, Ralink RT3072. Workaround for faulty firmware binary: Place file rt2870.bin from [https://launchpad.net/ubuntu/oneiric/+source/linux-firmware/1.53/+files/linux-firmware_1.53.tar.gz linux-firmware_1.53.tar.gz] in /lib/firmware. [https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/770232 Explanation].
 
** DWA-160 (Version B1). USB ID 07d1:3c11, Ralink RT2870. On Debian requires the <code>firmware-ralink</code> package from the <code>Squeeze-firmware</code> non-free repository.
 
** DWA-160 (Version A2). USB ID 07d1:3a09, Atheros AR9170. (NOTE: I can only get it to work through powered USB hub) requires carl9170-fw firmware [http://http://aur.archlinux.org/packages.php/packages.php?ID=44102]
 
** WUA-1340 (Version A1). Works with Raspbian Wheezy after installing the firmware-ralink package from the non-free repository on Debian.
 
 
 
* '''Edimax'''
 
** [http://www.edimax.co.uk/en/produce_detail.php?pd_id=328&pl1_id=1&pl2_id=44 EW-7811Un] USB ID 7392:7811, RTL8192CU, driver blob [http://www.electrictea.co.uk/rpi/8192cu.tar.gz download] via [http://www.element14.com/community/docs/DOC-44703 Element14], works with WPA2-AES-CCMP ([http://www.ctrl-alt-del.cc/2012/05/raspberry-pi-meets-edimax-ew-7811un-wireless-ada.html howto]) (B) - [http://dl.dropbox.com/u/80256631/8192cu-latest.tar.gz Alternative driver download link that works with Raspian]. <b>Note:</b> With current Raspbian (2012-09-18-Wheezy) it is recognized immediately, the default module works fine; the configuration is easy using wireless-essid and wireless-key in /etc/network/interfaces.
 
** The EW-7811Un can be powered directly from the Raspberry Pi if the Raspberry Pi is powered using a well regulated power supply.
 
** A script-based installation for the [http://www.edimax.co.uk/en/produce_detail.php?pd_id=328&pl1_id=1&pl2_id=44 EW-7811Un] by MrEngman can be found [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=26&t=6256&hilit=edimax on the Raspberry Pi forums]. Tested with Debian Squeeze and Raspbian. [http://dl.dropbox.com/u/80256631/install-rtl8188cus.txt An installation guide can be found here.]
 
** Instructions for getting the [http://www.edimax.co.uk/en/produce_detail.php?pd_id=328&pl1_id=1&pl2_id=44 EW-7811Un] working in Raspbmc (tested RC3) can be found [http://forum.stmlabs.com/showthread.php?tid=780 here].
 
** Simple step-by-step instructions for [http://www.edimax.co.uk/en/produce_detail.php?pd_id=328&pl1_id=1&pl2_id=44 EW-7811Un] which uses the RTL8192 chipset [[RPi_edimax_EW-7811Un]](B)
 
** [http://www.edimax.com/en/produce_detail.php?pd_id=8&pl1_id=1&pl2_id=44 EW-7318USg] USB ID 148f:2573, rt73usb. RT2573 chipset. Works with powered usb-hub or shorted polyfuses.
 
** [http://www.edimax.co.uk/en/produce_detail.php?pd_id=261&pl1_id=1&pl2_id=44 EW-7711UAn], Ralink RT2870, works perfectly on Arch with a powered hub (not tested without yet). Simply required wireless_tools and wpa_supplicant, the drivers/firmware are included in kernel 3.0. I followed the Arch [https://wiki.archlinux.org/index.php/Wireless_Setup Wireless Setup] instructions.
 
 
 
* '''edup'''
 
** [[http://www2.buyincoins.com/details/usb-150m-wifi-wireless-lan-network-card-adapter-antenna-product-1916.html Edup 150MBPS Wi-Fi adapter]] USB ID: 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter. Driver is the RT2800USB module, I had to install the firmware as rt2870.bin in /lib/firmware.([http://raspberry-pi-notes.blogspot.com/2012/05/rt5370-cheap-micro-usb-wireless-dongle.html requires firmware-ralink from Wheezy]) (B)
 
** [http://dx.com/p/ultra-mini-nano-usb-2-0-802-11n-150mbps-wifi-wlan-wireless-network-adapter-48166?item=1&Utm_rid=24958662&Utm_source=affiliate Ultra-Mini Nano USB 2.0 802.11n 150&nbsp;Mbit/s Wi-Fi/WLAN Wireless Network Adapter] USB ID: ID 0bda:8176 Works stable when using VLC for internet radio receiver. Works stable 24/7 on two of my Raspberries used as webserver. Use method shown [http://www.raspberrypi.org/phpBB3/viewtopic.php?t=7471&p=91736 here] for Debian.
 
 
 
** [http://www.szedup.com/show.aspx?id=1681 edup nano EP-N8508] Use method shown  [http://www.raspberrypi.org/phpBB3/viewtopic.php?t=7471&p=91736 here] for Debian. Requires powered USB hub for adequate power. When directly powered by Raspberry Pi, it fails after a few minutes. (B) Unusable with analog audio because when data is being send or recieved the audio get disorted. Use script from [http://dl.dropbox.com/u/80256631/install-wheezy-beta-rtl8188cus-20120619.sh here] for Wheezy.
 
 
 
* '''Eminent'''
 
** EM4575 - rt2800usb driver.
 
 
 
* '''EnGenius'''
 
** EUB9603 EXT - Realtek r8712u driver
 
 
 
* '''Gigabyte'''
 
** Gigabyte GN-WB32L 802.11n USB WLAN Card. Works with the rt2800usb driver.
 
 
 
* '''GMYLE'''
 
** Wireless 11n USB Adapter. Uses RTL8188CUS chipset - cheap on eBay. Installs and works using the install-rtl8188cus-latest.sh script.
 
 
 
* '''IOGear'''
 
** [http://www.element14.com/community/docs/DOC-44703 GWU625] USB ID 0bda:8172, r8712u staging driver, included on Fedora Remix & Arch, must [http://www.element14.com/community/servlet/JiveServlet/download/44948-8-97488/r8712u_ko.zip download] for Debian Squeeze and install firmware - Realtek from non-free Squeeze repository. No need to download firmware when using Debian Wheezy (B)
 
 
 
* '''Linksys'''
 
** Linksys (Cisco) WUSB100 ver.2 1737:0078, tested on Raspbian; follow [http://www.brucalipto.org/linux/the-raspberry-diary-wusb100-wireless-n/ Brucalipto.org] instructions; not stress tested, but it works without issues for light network load.
 
** Linksys (Cisco) WUSB600N, test on Raspbian, details [http://elibtronic.ca/content/20120731/raspberry-pi-part-1-wifi-support here]
 
** Linksys WUSB54GC (manufactured 07/2008) No issues! needs powered hub on version 1.0 boards.
 
 
 
* '''LogiLink'''
 
** Wireless LAN USB 2.0 Nano Adapter 802.11n LogiLink [http://www.logilink.eu/showproduct/WL0084B.htm] is working even USB powered.
 
 
 
* '''Micronet'''
 
** Micronet SP907NS, 11N Wireless LAN USB Adapter (uses Realtek RTL8188CUS) works plugged directly into Raspberry Pi USB (B) [http://dl.dropbox.com/u/80256631/install-rtl8188cus.txt Debian installation instructions] IMPORTANT: read the instructions first to avoid problems, and [http://dl.dropbox.com/u/80256631/install-rtl8188cus-latest.sh Auto-install script]. The script has been used to install other adapters using the RTL8188CUS chip. [http://dl.dropbox.com/u/80256631/8192cu-latest.tar.gz Updated driver] that handles the latest rpi-updates that kill the original driver, download for manual installation, automatically installed by the Auto-install script.
 
 
 
* '''MSI'''
 
** 0db0:6861 MSI-6861 802.11g Wi-Fi adapter (US54G): works with external powered USB hub, requires firmware from [http://sourceforge.net/projects/zd1211/files/zd1211-firmware/ here], power management must be disabled: <code>iwconfig wlan0 power off</code>
 
  
* '''Mvix'''
+
=== USB 4G Dongles ===
** Mvix Nubbin (MS-811N): works out of the box on Raspbian "Wheezy" and does not need a powered USB hub.
+
==== Huawei ====
 
+
* Huawei E398 LTE USB Rotator Mobile Broadband
* '''Netgear'''
+
* Huawei E3372 LTE USB stick
** N150: Reported as WNA1100 device, uses the Atheros ar9271 chipset. On Debian, requires the <code>firmware-atheros</code> package from the <code>Squeeze-backports</code> non-free repository  (!)
 
** N150: Some versions reported as Realtek RTL8188CUS device. Read Micronet entry above and use RTL8188CUS script for installation. Works best plugged into powered USB hub.
 
** WG111v1: Prism54 chipset. Needs powered hub. Follow info for Prism54 chipset on Debian wiki.
 
** WG111v2: Realtek rtl8187 chipset. Seems to draw a lot of power; e.g. I can't power this and a USB thumb drive simultaneously.
 
** WNA1000M works with Raspberry Pi Model B Board v. BS1233.However when downloading torrents, when torrent pick up speed system become unresponsive.
 
 
 
* '''OvisLink'''
 
** Evo-W300USB: USB ID 148f:2270 Ralink Technology RT2770. apt-get install firmware-ralink
 
 
 
* '''Patriot Memory'''
 
** [http://patriotmemory.com/products/detailp.jsp?prodline=6&catid=69&prodgroupid=163&id=1198&type=20 PCUSBW1150] Wireless 11N USB adapter  (uses Realtek RTL8188CUS) Install using Micronet script. Works only through powered USB hub.
 
** [http://www.patriotmemory.com/products/detailp.jsp?prodline=6&catid=69&prodgroupid=163&id=973&type=20 PCBOWAU2-N] Wireless 11N USB adapter  (uses Realtek RTL8191SU chip) Installed using r8712u Kernel module
 
 
 
* '''Ralink'''
 
** inner 02 joggler Wi-Fi USB RT2770F  USB-ID 148f:2770 (firmware-ralink required) (only got dhcp on powered hub)
 
** [http://www.dx.com/p/24688 RT2070] USB-ID 148f:2070 firmware is already loaded into Raspbian. For Debian, the firmware must be installed ([http://wiki.debian.org/rt2870sta instructions]). Needs a powered USB hub.
 
** RT3070 USB-ID 148f:3070 firmware is already loaded into Raspbian.
 
** [http://www.element14.com/community/docs/DOC-44703 RT2501/RT2573] USB-ID 148f:2573 (firmware-ralink required) (B)
 
** RT5370 USB-ID 148f:5370 ([http://raspberry-pi-notes.blogspot.com/2012/05/rt5370-cheap-micro-usb-wireless-dongle.html requires firmware-ralink from Wheezy]) [[RPi_Ralink_WLAN_devices]](B). An image of an adapter with this chip can be found [http://i.imgur.com/wRF7L.jpg here].
 
 
 
* '''Rosewill'''
 
** RNX-N180UBE Wireless B/G/N Adapter
 
*** Realtek RTL8191SU chipset, USB-ID 0bda:8172
 
*** Tested in Arch, works out of box. Powered USB hub required.
 
*** Tested in Raspbian, used wicd to configure network settings.  Powered USB hub Required.
 
*** Tested in Raspbmc. Needs package firmware - Realtek and used wicd-curses to configure. Powered USB hub required
 
** RNX-G1 Wireless B/G Adapter
 
*** Realtek RTL8187 chipset, USB-ID 0bda:8187
 
*** Tested in Arch, works out of box. USB hub required.
 
** RNX-MiniN1 (RWLD-110001) Wireless-N 2.0 Dongle (Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter)
 
*** Tested in Raspbian, powered from USB hub.
 
 
 
* '''Sabrent'''
 
** USB-A11N: Mini USB 2.0 Wireless-N WiFi Network Adapter: USB ID 0bda:8176, works automatically in Raspian using rtl8192cu driver along with Logitech BT mini-receiver (keyboard/mousepad) without external hub using 5.25V 1 A psu (4.99V T1/T2) on rev 2.0 (B)
 
 
 
* '''Sagem'''
 
** Sagem Wireless USB stick XG-760N: USB ID 079b:0062, Module is not shipped in Debian image, but it can be "sudo apt-get install zd1211-firmware"
 
 
 
* '''Sempre'''
 
** Sempre Wireless USB stick WU300-2: USB ID 0bda:8172, Realtek r8712u driver + firmware-realtek package. Module is shipped in Raspbian image. If you need to build it for other distros, read this: http://www.t3node.com/blog/sempre-wireless-usb-stick-wu300-2-on-raspberry-pi/
 
 
 
* '''Sitecom'''
 
** Sitecom Wi-Fi USB Adapter N300: USB ID 0a5c:5800, Realtek r8712u driver + firmware Realtek. Module available in shipped Raspbian image. '''NOTE:''' although this dongle will also work without powered hub, if there is a voltage problem (either on the Raspberry or on the hub, but verified only on the hub so far) this wifi dongle will receive signal perfectly (RX), but not be capable of sending anything (TX) and the MAC address will be permanently set to FF:FF:FF:FF:FF:FF (this is indicative that there is not enough power) [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=24247]
 
 
 
* '''SL'''
 
** SL-1507N: USB 802.11n 150M Wi-Fi Wireless LAN Network Card Adapter SL-1507N Black
 
*** I bought this on on eBay for $4.19 (free shipping) @ http://www.ebay.com/itm/270853614804?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#ht_4379wt_1199
 
*** It worked out of the box on Raspbmc RC4, with the network manager add-on; seems to be an rt2800usb
 
*** dmesg output "usbcore: registered new interface driver rt2800usb"
 
 
 
* '''SMC'''
 
** SMCWUSBS-N: Hardware detected as rt2800, but it is missing firmware; "sudo apt-get install firmware-ralink" fixed it
 
** SMCWUSB-G: Gives "couldn't load firmware" error. "sudo apt-get install zd1211-firmware" fixes it.
 
 
 
* '''Sony'''
 
** Sony UWA-BR100 802.11abgn Wireless Adapter [Atheros AR7010+AR9280] (Vendor ID: 0411, Product ID: 017f) - Tested with Raspbian. Needs package firmware-atheros.(B)
 
 
 
* '''Tenda'''
 
** USB 11n adapter on a G network: Ralink  2870/3070 driver (!)
 
** Tenda W311MI Wireless N Pico USB Adapter (identified as Ralink RT5370 Wireless Adapter; USB-ID: 148f:5370) - Works out-of-the-box for Raspian 2012/09/18 or later. An earlier version gave me problems.
 
** Tenda W311U Mini 11N Wireless USB Adapter (USB-ID 148f:3070): Ralink  2870/3070 driver; needs powered hub. [http://blog.modmypi.com/2012/06/installing-tenda-w311u-mini-wireless.html Debian installation instructions]
 
** Tenda W311U+ Wireless USB Adapter - Tested with Raspian.
 
 
 
*'''The Pi Hut'''
 
** USB 802.11n Wi-Fi adapter (from [http://thepihut.com/products/usb-wifi-adapter-for-the-raspberry-pi The Pi Hut's Raspberry Pi Store])
 
 
 
* '''TP-Link'''
 
** TL-WN422G v2 (ath9k_htc) Works OOTB in Debian Wheezy Beta. Runs without powered Hub when plugged into running Raspberry Pi, but the Raspberry Pi won't boot while the stick is plugged in.
 
** TL-WN721N (ath9k_htc device with htc_9271.fw file from http://linuxwireless.org/download/htc_fw/1.3/htc_9271.fw); needs powered USB Hub (B) | works OOTB with Wheezy Raspbian (2012-08-16) connected directly to raspberry pi (B) and AP functionality tested with hostapd.
 
** TL-WN722N (ath9k_htc device with htc_9271.fw file from http://linuxwireless.org/download/htc_fw/1.3/htc_9271.fw); needs powered USB Hub (B)
 
** TL-WN723N (RTL8188SU); works OOTB with Raspbian 2012-09-17, (B) stable with 1&nbsp;A PSU and without powered USB hub on r2.0.
 
** TL-WN821N v3 (ath9k_htc, htc_7010.fw); works out of the box on ArchLinuxARM, Wheezy and on OpenElec (>r11211), Problems with prior OpenElec; needs powered USB Hub (B). This chipset is also compatible with hostapd (wireless AP software)
 
** TL-WN823N Works out of box on Raspian using powered USB Hub
 
 
 
* '''Trendnet'''
 
** [http://www.wikidevi.com/wiki/TRENDnet_TEW-648UBM TEW-648UBM] USB ID: 20f4:648b, works OOTB with [http://learn.adafruit.com/adafruit-raspberry-pi-educational-linux-distro/ Adafruit Occidentials Raspbian Wheezy variant] as it includes kernel with [http://www.wikidevi.com/wiki/Special:Ask?title=Special%3AAsk&q=%5B%5BChip1+model%3A%3ARTL8188CUS%5D%5D&po=%3FInterface%0D%0A%3FFCC+ID%0D%0A%3FVendor+ID%0D%0A%3FDevice+ID%0D%0A%3FChip1+model%0D%0A%3FSupported+802dot11+protocols%0D%0A%3FMIMO+status%0D%0A%3FOUI%0D%0A&sort_num=&order_num=ASC&eq=yes&p%5Bformat%5D=broadtable&p%5Blimit%5D=500&p%5Bsort%5D=&p%5Boffset%5D=&p%5Bheaders%5D=show&p%5Bmainlabel%5D=&p%5Blink%5D=all&p%5Bsearchlabel%5D=&p%5Bintro%5D=&p%5Boutro%5D=&p%5Bdefault%5D=&p%5Bclass%5D=sortable+wikitable+smwtable&eq=yes RTL8188CUS driver built-in] (B)
 
 
 
* '''Widemac'''
 
** RT5370 Wireless Adapter from [http://www.ebay.co.uk/itm/180887771838?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 Ebay] runs without powered hub. Follow these [http://elinux.org/RPi_Ralink_WLAN_devices instructions], but go to [http://ftp.de.debian.org/debian/pool/non-free/f/firmware-nonfree/ ftp.de.debian.org/debian/pool/non-free/f/firmware-nonfree/] and pick the latest firmware-ralink_0.xx_all.deb
 
 
 
* '''ZyXEL'''
 
** [http://www.element14.com/community/message/50015#50015/l/re-installing-kernel-headers-on-the-pi NWD2105] USB ID: 0586:341e, RT3070 chipset, rt2800usb driver (B)
 
** [http://www.zyxel.com/products_services/g_202.shtml G-202] model 0586:3410 ZyXEL Communications Corp. ZyAIR G-202 802.11bg using zd1211rw kernel module and zd1211-firmware package
 
 
 
===Problem USB Wi-Fi Adapters===
 
 
 
These adapters were tested and found to have issues the Raspberry Pi. Note [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=6928] as a possible solution/explanation for errors while running LXDE.
 
 
 
* '''Alfa'''
 
** AWUS036NHA (Vendor ID: 0cf3, Product ID: 9271) - Tested with Raspbian. Works fine if connected after boot. Kills boot process if previously attached. [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=16809&p=169469#p169469 Details here.]
 
 
 
* '''EDIMAX'''
 
** EW-7811Un (Vendor ID: 7397, Product ID: 7811) - Reports as containing the Realtek RTL8188CUS chipset listed below, no lockup or kernal oops under Wheezy, but dmesg reports constant timeouts trying to initialize the module. This appears to be resolved on 2012-09-18-Wheezy-raspbian and newer versions.
 
 
* '''Linksys'''
 
** WUSB300N (Vendor ID: 13B1, Product ID: 0029) - Tested with Raspbian, OpenELEC, among others.  No Linux chipset support for Marvell 88W8362 at all.
 
 
 
* '''LogiLink'''
 
** WL0085 tested under Debian (Squeeze, Wheezy, Raspbian); no stable connection can be established. This gets even worse when X is running.
 
 
 
* '''MicroNEXT'''
 
** MN-WD152B (Debian image) modprobe hangs when plugged in, lsusb hangs. udevd errors in the logs. [http://www.element14.com/community/thread/17632] [http://www.raspberrypi.org/phpBB3/viewtopic.php?t=6737]
 
*** Possible fix: try the new [http://learn.adafruit.com/adafruit-raspberry-pi-educational-linux-distro/occidentalis-v0-dot-1 Adafruit Occidentalis v0.1] image (based on Raspbian Wheezy) as it includes the needed 8192cu driver builtin to the kernel
 
 
 
* '''Netgear'''
 
** WNDA3100v2 tested with Debian (Wheezy); no driver for broadcom chipset (see [http://www.wikidevi.com/wiki/Netgear_WNDA3100v2 http://www.wikidevi.com/wiki/Netgear_WNDA3100v2]).
 
 
 
* '''Realtek'''
 
** RTL8188CUS USB-ID 0bda:8176, kernel oops in dmesg and freeze when pulled from USB. (B)
 
 
 
* '''Trendnet'''
 
** [http://www.element14.com/community/docs/DOC-44703 TEW-424UB] USB ID: 0bda:8189; tested on Debian, Fedora & Arch; rtl8187 driver; errors with LXDE running (B)
 
 
 
* '''TP-Link'''
 
** [http://www.element14.com/community/docs/DOC-44703 TL-WN821N] USB ID: 0cf3:7015; tested on Debian; requires [http://linuxwireless.org/download/htc_fw/1.3/htc_7010.fw htc_7010.fw] firmware; ath9k_htc driver; errors with LXDE running (B)
 
** TL-WN723N USB ID: 0bda:8176; tested on Arch without a powered hub; it seems to draw too much current.
 
 
 
== USB Bluetooth adapters ==
 
===Working Bluetooth adapters===
 
* Asus USBIA-EG (paired with Asus Blutooth Keyboard/Media Center Remote
 
** Verified works error-free in Multiple Distros (Openelec, Raspbian, RaspBMC, Xbian) Latest builds eliminate text echo problems.
 
* Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) - (USB ID 0a12:0001)
 
** Example of above is; TOPDIGI UA01 Bluetooth USB Dongle Plug and Play (install bluez package from std repos)
 
** Tesco own brand 'Technika' Nano Bluetooth Adaptor has the Cambridge Silicon Radio chipset and works fine, cost £5.97 at time of posting.
 
** Hama USB Bluetooth 3.0 adapter (Class 1) ~£10 on amazon.co.uk.
 
** Another sample: Product ID: 0a12:0001, pictured here: http://www.element14.com/community/message/58288
 
** RiiTek RT-MWK02+ - comes with a USB Bluetooth adapter that works perfectly for both the RiiTek mini Bluetooth keyboard/mouse and other Bluetooth devices. Tested both on builtin USB and on powered USB hub. There are other RiiTek Bluetooth (and non-Bluetooth wireless) devices on the working list. Bluetooth adapter shows up in lsusb as "0a12:0001 Cambridge Silicon Radio" - this is notable as most other sources of this chipset do not seem to be available in the US.
 
* D-Link DBT-122, with ID 07d1:f101, using a Broadcom chip
 
** http://www.element14.com/community/message/58288
 
* IOGear GBU321 (Broadcom BCM2045 Chipset)
 
** Works with Raspbian Wheezy directly attached to Raspberry Pi and via powered USB hub.
 
* Trust BT-2400p
 
** Working well with Raspbian Wheezy directly attached to Raspberry Pi. Using with sma-Bluetooth (SMA Solar Inverter reading software).
 
 
 
===Problem Bluetooth adapters===
 
* '''Belkin'''
 
** Belkin F8T017. Tested with Raspbian 2012-07-15 and bluez installed with apt-get. When dongle is inserted into Pluscom powered USB hub, my remote PuTTY session scrolls incredibly slowly (testing with ls -R to generate text). Suspect network issue. Lots of errors on dmesg too. Raspberry Pi itself is responsive when using directly. On removal of the device everything goes back to normal.
 
* '''Generic'''
 
** [http://dx.com/p/mini-bluetooth-v3-0-usb-2-0-dongle-71248 Bluetooth "3.0" Dongle]. Doesn't work reliably - eg. after some time it will hang and the device will need to be reset using fcntl. The device id is 1131:1004 Integrated System Solution Corp. Bluetooth Device.
 
* Asus USB-BT211
 
** Shows up as HCI device in Raspbian, but it does not scan or pair.
 
** http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=9962
 
 
 
== USB Ethernet adapters ==
 
===Working Ethernet adapters===
 
* '''AVM'''
 
** FRITZ!Box WLAN 3030 USB Ethernet Adapter: Works out of the box. No external power source needed.
 
* '''Wintech'''
 
** USB 2.0 LanCard Model: LAU-15 (CK0049C) using the mcs7830 driver. Probably needs more than 100&nbsp;mA current. [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=46&t=8708#p106136]
 
* '''LogiLink'''
 
** USB 2.0 UA0144: AX88772 chipset using the asix kernel driver. Tested only on powered USB hub so far.
 
** LogiLink Fast EN USB 2.0 to RJ45 Adapter: Test on Wheezy-Raspian (2012-08-16) without USB Hub will be confirmed
 
lsusb output: Bus 001 Device 004: ID 9710:7830 MosChip Semiconductor MCS7830 10/100 Mbps Ethernet adapter
 
* '''Apple'''
 
** Apple USB Ethernet Adapter using asix kernel driver. Works out of the box on Raspbian, haven't tested on any other OS.
 
* '''Edimax'''
 
** Edimax EU-4230 USB2.0 Fast Ethernet Adapter with 3 port USB hub. Works out of the box. Needs its own power source.
 
* '''D-Link'''
 
** D-Link DUB-E100 Fast Ethernet USB 2.0 Adapter - works out of the box, requires own power supply (from powered USB hub)
 
* '''Sitecom'''
 
** Sitecom LN-030 V2 detected as ASIX AX88772 USB 2.0 Ethernet Adapter works out of the box. Doesn't seem to require any extra power supply.
 
* '''A-Link'''
 
** A-Link NA1GU Gigabit USB 2.0 Ethernet adapter
 
This adapter works, but it (probably) requires a bit of work. The driver for the chipset (Asix AX88178) included with the Raspbian kernel (v 3.1.9+ Aug 7 2012) does '''not''' work. With that driver the device is detected, but it does not seem to be possible to actually put any traffic through it. :-( In order to make it work you need to download the latest driver from [http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=84;71;100&PLine=71 the chipset manufacturer]. The version I used was "Linux kernel 3.x/2.6.x Driver" v4.4.0, released 2012-05-18. Fortunately this is GNU GPLv2 -licenced source code and not a binary blob, so compiling it for the Raspberry Pi is perfectly doable. The hardest part was in fact getting the Linux source code required, because the repositores contained the source for the wrong kernel version. >:-( Fortunately there is [https://www.grendelman.net/wp/compiling-kernel-modules-for-raspbian-raspberry-pi a very useful guide] for how to get the sources from github, and preparing that source so that you can compile modules. Unfortunately you will have to compile the kernel (even if you don't actually install it) - which will take the better part of the day on the Raspberry, but once that's done you can unpack the driver source and just run "make && sudo make install". Reboot and you should have a fully working Ethernet adapter.
 
 
 
The adapter seems to work without a powered USB hub, but according to the specifications it can draw up to 190&nbsp;mA, so there might be stability issues if additional power is not provided.
 
* '''Hama'''
 
** Hama 00049244 Fast Ethernet USB 2.0-Adapter detected as MOSCHIP 7830/7832/7730 usb-NET adapter. Works out of the box on Debian Wheezy/sid (2012-08-08-wheezy-armel)(not tested yet on other OS). No external power source or USB hub needed.
 
 
 
===Problem Ethernet adapters===
 
* Axago
 
** Axago ADE-X1 10/100 Ethernet Adapter (USB: 9710:7830 driver:mcs7830). Adapter working about 10 minutes without problem, but after that kernel write error message to dmesg and no packet is received. Needed to unplug and plug USB again. Tested with and without powered USB hub.
 
  
 
== USB Sound Cards ==
 
== USB Sound Cards ==
Line 1,484: Line 135:
 
* '''Edirol'''
 
* '''Edirol'''
 
** [http://www.roland.com/products/en/UA-1A/ UA-1A]
 
** [http://www.roland.com/products/en/UA-1A/ UA-1A]
 +
* '''GWCtech'''
 +
** [http://www.gwctech.com/product3.asp?listid=3&id=4&subid=10&pid=788&typeid=96 AA1570 USB 7.1 Sound Card] (aka [http://www.conrad.com/ce/en/product/872990/USB-SoundBox-71 Conrad AA 1570 7.1 SoundBox]) - playback works fine, Recording stutters unless dwc_otg.speed=1 is set
 
* '''Hercules'''
 
* '''Hercules'''
 
** [http://www.hercules.com/fr/Cartes-Son/bdd/p/123/gamesurround-muse-xl-pocket-lt3/ Gamesurround Muse XL (Pocket LT3)]
 
** [http://www.hercules.com/fr/Cartes-Son/bdd/p/123/gamesurround-muse-xl-pocket-lt3/ Gamesurround Muse XL (Pocket LT3)]
 +
* '''Hewlett Packard'''
 +
** Hewlett Packard (HP) Premium Digital Headset, Model No: HUD-02. It supports both audio out and audio in.  Works in Audacity.  Recprding volume is quiet even with recording mixer level turned way up.  Additional post-mixer amplification of audio-in is recommended, if possible.
 +
* '''Kingwin'''
 +
** [http://www.kingwin.com/adapters/usb-sound-adapter/ USB-3DSA] (Both audio out/in work, lsusb lists as "C-Media USB Headphone Set")
 
* '''Logilink'''
 
* '''Logilink'''
 
** [http://www.logilink.de/showproduct/UA0053.htm?seticlanguage=en UA0053 USB Soundcard with Virtual 3D Soundeffects LogiLink]
 
** [http://www.logilink.de/showproduct/UA0053.htm?seticlanguage=en UA0053 USB Soundcard with Virtual 3D Soundeffects LogiLink]
 +
* '''Logitech'''
 +
** [http://www.amazon.com/Logitech-Wireless-Gaming-Headset-Surround/dp/B003VANOFY/ref=sr_1_1?ie=UTF8&qid=1358114107&sr=8-1&keywords=g930 Logitech G930 Wireless Gaming Headset with 7.1 Surround Sound] (stereo works with ALSA, have not tried 7.1 Surround Sound)
 
* '''NuForce uDAC-2'''
 
* '''NuForce uDAC-2'''
 
** [http://www.nuforce.com/hp/products/iconudac2/index.php NuForce uDAC-2 Headphone Amplifier and USB DAC]
 
** [http://www.nuforce.com/hp/products/iconudac2/index.php NuForce uDAC-2 Headphone Amplifier and USB DAC]
 +
* '''Plantronics'''
 +
** [http://www.ebay.com/itm/Genuine-New-Plantronics-External-USB-Audio-Soundcard-New-Sealed-/300845395889?pt=US_Sound_Card_External&hash=item460bc86fb1 Plantronics Stereo USB Adapter -01] (works with ALSA) (shows up in lsusb as 0d8c:000c C-Media Electronics, Inc. Audio Adapter)
 +
* '''SpeedLink'''
 +
** [http://www.speedlink.com/?p=2&cat=17&pid=23371&paus=1&act_lang=en VIGO USB Soundcard, black] - Device ID: 0d8c:000e ("C-Media Electronics, Inc. Audio Adapter"). Working, but on Raspbian 3.6.11 it fills up kern.log with "cm109_urb_irq_callback: urb status -71" messages. To prevent this, you can insert `:msg, contains, "cm109_urb_irq_callback" ~´ as first rule into /etc/rsyslog.conf.
 
* '''Terratec'''
 
* '''Terratec'''
 
** [http://www.terratec.net/fr/produkte/Aureon_Dual_USB_12339.html Aureon Dual USB] (not with USB high speed; add dwc_otg.speed=1 to /boot/cmdline.txt, but that will slow down all USB transfers)
 
** [http://www.terratec.net/fr/produkte/Aureon_Dual_USB_12339.html Aureon Dual USB] (not with USB high speed; add dwc_otg.speed=1 to /boot/cmdline.txt, but that will slow down all USB transfers)
 
* '''Texas Instruments PCM2704'''
 
* '''Texas Instruments PCM2704'''
** [http://www.ti.com/product/pcm2704 PCM2704 98&nbsp;dB SNR Stereo USB2.0 FS DAC with line-out and S/PDIF output, Bus/Self-powered]
+
** [http://dx.com/p/usb-dac-pcm2704-decoder-red-172991?Utm_rid=24958662&Utm_source=affiliate USB DAC PCM2704 Decoder]
  
==USB 3G Dongles==
+
=== Databases of supported sound cards ===
* Huawei E173
+
* http://wiki.linuxaudio.org/wiki/current_audio_gear
* Huawei E220
+
* http://wiki.linuxmusicians.com/doku.php?id=hardware_matrix
* Huawei E160 (AT commands only)
+
 
* Franklin U600 from Sprint / VirginMobile
+
=== Class compliant USB sound cards ===
** Use usb_modeswitch and vendor 0x1fac and product 0x0150/0x0151
+
 
* Digicom Internet Key 7.2 HSUPA '''MU372-L01''' [http://www.digicom.it/digisit/prodotti.nsf/itprodottiidx/MU372L01]
+
Any USB1.1 audio interface that is class compliant should work with Linux, same goes for USB2.0 interfaces that adhere to the current USB audio standards. There are some interfaces that are supported in Linux while they do not comply to the standards because specific quirks have been added to the USB Linux drivers. To verify if your interface is supported search for a manual of your interface and check if it needs drivers to run under Windows/Mac. If the manual explicitely mentions no drivers are needed the interface is almost surely a class compliant device. When in doubt check the aforementioned databases.
Tested on Raspbian and Archlinux. Detected as 230d:0001. Works with cdc_acm driver. Install usb_modeswitch.
+
 
There are 2 "com ports"( /dev/ttyACM0 and /dev/ttyACM1 ) . Tested with Network Manager.Works also perfectly with SAKYS3G [http://www.sakis3g.org/] tools  (!! led is always off !!) and wvdial. A working wvdial.conf: http://ubuntuforums.org/showpost.php?p=10361881&postcount=28  . (for example for Vodafone IT , replace Init3 with this:  Init3 = AT+CGDCONT=1,"IP","web.omnitel.it"  and replace line Modem = /dev/ttyUSB0  with Modem = /dev/ttyACM1 )  and run with  wvdial voda  .
+
=== Troubleshooting ===
 +
If you encounter problems setting up your USB soundcard check the RPi Wiki article in the linuxaudio.org Wiki: http://wiki.linuxaudio.org/wiki/raspberrypi
 +
 
 +
* Bulleted list item
  
 
== USB IR Receivers==
 
== USB IR Receivers==
SMK Manufacturing, Inc. eHome Infrared Receiver (Works out of the box with OpenELEC)
+
* The [http://www.pi-supply.com/product/flirc-usb-ir-remote-dongle-for-raspberry-pi/ FLIRC] USB dongle allows the use of any remote control with your Raspberry Pi. Configure the device on your desktop PC, then simply plug into your Pi for a perfect media center companion. Available from [http://www.pi-supply.com/ Pi Supply], [http://thepihut.com/ The Pi Hut] and [http://www.buyraspberrypi.com.au Buy Raspberry Pi Australia]
 +
 
 +
* SMK Manufacturing, Inc. eHome Infrared Receiver (Works out of the box with OpenELEC)
  
 
== USB Radio devices==
 
== USB Radio devices==
Line 1,514: Line 182:
 
== USB TV Tuners and DVB devices==
 
== USB TV Tuners and DVB devices==
 
*August
 
*August
**DVB-T205, based on rtl2832u chipset, working with [https://github.com/ambrosa/DVB-Realtek-RTL2832U-2.2.2-10tuner-mod_kernel-3.0.0 this driver]. Tested with Saorview (Irish DTT service), both HD & SD.
+
**DVB-T205, based on rtl2832u chipset, worked with [https://github.com/ambrosa/DVB-Realtek-RTL2832U-2.2.2-10tuner-mod_kernel-3.0.0 this driver] on older 3.2 kernel. Couldn't get same device working reliably on current kernel. (On the older 3.2 kernel it worked with Saorview (Irish DTT service), both HD & SD.)
 +
*Derek?
 +
**TV28T v2 USB DVB-T & RTL-SDR Receiver, RTL2832U & R820T Tuner, MCX Input. DVB-T works with OpenElec 4.2.1 connected to the PiHub, tvheadend backend + frontend, finds all expected, non-encrypted channels in the south of Germany. I did not try to use the remote.
 
*DVBSky
 
*DVBSky
 
**[http://dvbsky.eu/Products_S860.html Mystique SaTiX-S2 Sky USB]: Scanning/watching SD and HD works via vdr and streamdev plugin, watching on the Raspberry Pi directly is laggy as hell. DVB-USB and I2C support must be enabled in the kernel. Needs drivers/firmware from [http://dvbsky.eu/Support.html here].
 
**[http://dvbsky.eu/Products_S860.html Mystique SaTiX-S2 Sky USB]: Scanning/watching SD and HD works via vdr and streamdev plugin, watching on the Raspberry Pi directly is laggy as hell. DVB-USB and I2C support must be enabled in the kernel. Needs drivers/firmware from [http://dvbsky.eu/Support.html here].
Line 1,525: Line 195:
 
** Hauppauge NOVA-T Stick (Revision 70xxx) DiBcom DiB0700 chipset, requires powered hub.
 
** Hauppauge NOVA-T Stick (Revision 70xxx) DiBcom DiB0700 chipset, requires powered hub.
 
** Hauppauge NOVA-TD Stick (Revision 52xxx) DiBcom DiB0700 chipset, requires powered hub.
 
** Hauppauge NOVA-TD Stick (Revision 52xxx) DiBcom DiB0700 chipset, requires powered hub.
** Hauppauge  WinTV-HVR-1950 (tested analog tuner with omxplayer)
+
** Hauppauge  WinTV-HVR-1950 (tested analog tuner with omxplayer, tested Digital OTA with MythTV)
 
** Hauppauge  WinTV-HVR-950Q (tested Digital OTA with TVHeadend in Raspbian)
 
** Hauppauge  WinTV-HVR-950Q (tested Digital OTA with TVHeadend in Raspbian)
 
*K-World
 
*K-World
Line 1,531: Line 201:
 
*Technisat
 
*Technisat
 
**Technisat_SkyStar_USB_HD. Instructions: http://www.linuxtv.org/wiki/index.php/Technisat_SkyStar_USB_HD Used the Raspberry Pi to receive and redirect it via network to another host. Didn't try to play back the stream on the Raspberry Pi itself. Tested with Astra 19.2E radio and SD-TV channels
 
**Technisat_SkyStar_USB_HD. Instructions: http://www.linuxtv.org/wiki/index.php/Technisat_SkyStar_USB_HD Used the Raspberry Pi to receive and redirect it via network to another host. Didn't try to play back the stream on the Raspberry Pi itself. Tested with Astra 19.2E radio and SD-TV channels
 +
*TECHNOTREND
 +
**TT-TVStick CT2-4400 USB Fernbedienung rev2. DVB-T works with OpenElec 4.9.4 BETA connected to the PiHub, tvheadend backend + frontend, finds all expected, non-encrypted channels in the south of Germany. DVB-C also works, finds around >30 TVs and >100 radio stations. I did not try to use the remote, nor did I listen to any radio station. TV works, SD channels are ok, HD channels jitter. tvheadend backend crashes often within OpenElec 4.9.4 BETA, but restarts, so still buggy but looks good(BETA!). It did not work out of the box with the stable OpenElec 4.2.1.
 +
* Terratec
 +
** Terratec H7. Tested DVB-C with [http://git.linuxtv.org/v4l-utils.git dvbv5 tools, part of v4l-utils], under [http://zenit.senecac.on.ca/wiki/index.php/Raspberry_Pi_Fedora_Remix Fedora 18 Remix] and latest (April, 14 2013) [http://git.linuxtv.org/media_build.git DVB Kernel stack/drivers].
 
*Generic
 
*Generic
 
** [http://www.onsources.com/product_images/a/757/watch_and_record_digital_tv_dongle__44323_zoom.jpg DVB-T USB Dongle (Silver casing)], based on AF9015 chipset.
 
** [http://www.onsources.com/product_images/a/757/watch_and_record_digital_tv_dongle__44323_zoom.jpg DVB-T USB Dongle (Silver casing)], based on AF9015 chipset.
 
** [http://www.electrodepot.fr/media/catalog/product/cache/1/image/500x/9df78eab33525d08d6e5fb8d27136e95/P926993.jpg DVB-T USB Dongle], based on RTL2832 FC12 (HD/SD), IR was detected, but it is not tested.
 
** [http://www.electrodepot.fr/media/catalog/product/cache/1/image/500x/9df78eab33525d08d6e5fb8d27136e95/P926993.jpg DVB-T USB Dongle], based on RTL2832 FC12 (HD/SD), IR was detected, but it is not tested.
 +
** [http://obrazki.elektroda.pl/8081115000_1317678968.jpg HDTV USB DVB-T] dongle, based on IT9135. This tuner comes in two revisions. Revision is printed on PCB.
 +
*** rev. 1.0; should work with 3.2+ kernel, need confirmation.
 +
*** rev. 2.0; works with kernel 3.6.11, without a powered hub. This tuner also requires a firmware (dvb-usb-it9135-02.fw) which can be downloaded from [http://logout.hu/bejegyzes/azbest/usb_dvb-t_tuner_it9135_rev2/hsz_1-50.html this page]. It's in Hungarian, so google translate or equivalent is recommended. The remote also works.<br>According to [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=35&t=29141 this post], there may be issues on some software configurations when using ''omxplayer''.
  
== USB Webcams ==
+
== USB Video / Frame grabbers==
  
This list is not entirely reliable, working does not necessarily mean working without errors. Please contribute with your own experiences!
+
* EasyCAP DC60 (STK1160 chip) - works out of the box for older versions of Raspbian. If you're getting grey stripes see this [http://raspberry-at-home.com/video-grabber-for-raspberry-pi/ tutorial]
 +
* EasyCAP (UTV007 Fushicai chip) - works after driver compilation - see instructions at [http://raspberry-at-home.com/video-grabber-for-raspberry-pi/ this link]. remember to use older Raspbian version.
 +
* Hauppage HVR 1900
  
===USB Webcams===
+
== USB Webcams ==
<div style="margin: -.3em -1em -1em -1em;">
 
{| width="100%" bgcolor="#fff" border="0" cellpadding="2px" cellspacing="2px" style="margin:auto;"
 
|- align="center" bgcolor="#e7eef6"
 
| '''Brand'''
 
| '''Name'''
 
| '''Model Number'''
 
| '''Hardware ID'''
 
| '''Verified OS'''
 
| '''Verified OS version'''
 
| '''Verified Resolution'''
 
| '''Additional Information'''
 
 
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Canyon
 
|
 
|CNR-WCAM820
 
|
 
| raspbian/wheezy
 
|
 
| 1280x1024
 
| 2 Mpixel camera with manual focus; works with fswebcam and v4l4j on Raspbian Wheezy armhf; problems with 1600x1200 resolution in some apps (timeouts - probably too slow USB); 1280x1024 and lower resolutions works OK
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Creative
 
|Live!
 
| VF0470
 
|
 
| ArchLinux
 
|
 
|
 
| works out of the box on ArchLinux
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Creative
 
|Live! Cam Socialize HD
 
| VF0610
 
|041e:4080
 
| raspbian/wheezy
 
| 2012-11-26
 
| 960x544
 
| Works at 1280x720 taking stills in fswebcam with some errors using MJPEG, unusable with YUYV. 960x544 works in both MJPEG and YUYV. Has some stabilitiy issues if powered from RasPi (Drops USB +eth0 every 8 or so hours). Helps to append nodrop=1 and timeout=5000 to uvcvideo module.
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Creative
 
|Live! Cam Vista IM
 
| VF0640
 
|
 
| raspbian/wheezy
 
|
 
|
 
| works on Raspbian at 320x240 resolution, 15fps
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Creative
 
|Webcam Notebook
 
| PD1170
 
|
 
|
 
|
 
|
 
| Detects, untested.
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Creative
 
|Webcam Pro
 
| PD1030
 
|
 
|
 
|
 
|
 
|  ov519 driver crashes almost immediately. ("gspca: ISOC data error: [0] len=0, status=-4004")
 
 
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|HP
 
|WebcamHD-2200
 
| HD-2200
 
|
 
|
 
|
 
|
 
|
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|HP
 
|Webcam HP-3100
 
|HP-3100
 
|
 
|
 
|
 
|
 
| UVCVideo /dev/video0 Needs chmod to 666 to operate. Will work without hub if only device in USB ports. Works with both Arch and Wheezy out of the box
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C100
 
| V-U0013
 
|
 
| raspbian/wheezy
 
| 2012-08-16
 
|
 
| works fine without powered hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C200
 
|
 
| 046d:0802
 
|
 
|
 
|
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C270
 
|
 
|
 
|
 
|
 
|
 
| With external power
 
  
|- valign="top" align="left" style="background: #F5FAFF;"
+
This section has been moved to a separate page. See [[RPi USB Webcams]]
|Logitech
 
|Webcam C310
 
|
 
|
 
|
 
|
 
|
 
| Does not require a powered hub to capture snapshots
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C510
 
|
 
|
 
|
 
|
 
|
 
|
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C525
 
|
 
|
 
|
 
|
 
|
 
| Works fine without powered hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C615
 
|
 
|
 
|
 
|
 
|
 
| Works fine without powered hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C910
 
|
 
|
 
|
 
|
 
|
 
| With external power, is uncvideo
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|Webcam C920
 
|
 
|
 
| raspbian/wheezy
 
|
 
|
 
| With powered hub, detected out of box as Video0 V4L device
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|QuickCam Orbit/Sphere
 
|
 
|
 
|
 
|
 
|
 
| Works with external power
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Logitech
 
|QuickCam Pro 9000
 
|
 
|
 
| raspbian/wheezy
 
|
 
|
 
| Powered by RasPi
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Logitech
 
|Webcam Pro 4000
 
|
 
|
 
|
 
|
 
|
 
| It uses pwc driver which does not work. Maybe it's because of general Raspberry Pi USB bug.
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Logitech
 
|Webcam Pro 9000
 
|
 
| 046d:0809
 
| Arch Linux
 
|
 
|
 
| Powered by RasPi, measured ~120 mA current capturing at ~5fps. Has issues capturing images at higher than default resolutions (using motion - Arch and Debian).
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Medion
 
|
 
| MD86511
 
|
 
| raspbian/wheezy
 
| 2012-07-15
 
|
 
| Powered by RasPi
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|LifeCam Cinemap 720p USB HD Webcam
 
| H5D-00001
 
|
 
| raspbian/wheezy
 
|
 
|
 
|
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Microsoft
 
|LifeCam HD-5000
 
|
 
|
 
|
 
|
 
|
 
| Picture breaks up at the bottom
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|LifeCam HD-6000
 
|
 
|
 
| raspbian/wheezy 
 
|
 
|
 
| Powered by USB hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|LifeCam
 
| NX-6000
 
|
 
| raspbian/wheezy
 
|
 
|
 
| Powered by USB hub
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|LifeCam
 
| VX-7000
 
|
 
| raspbian/wheezy
 
|
 
|
 
| Powered by USB hub
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Microsoft
 
|LifeCam
 
| VX-3000
 
|
 
| raspbian/wheezy
 
|
 
|
 
| There do appear to be some issues with image quality and getting partial frames and such, with fswebcam
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|LifeCam
 
| NX-6000
 
|
 
| raspbian/wheezy
 
|
 
|
 
| Powered by USB hub
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Microsoft
 
|LifeCam
 
| VX-800
 
|
 
| raspbian/wheezy
 
|
 
| 352x288
 
| Doesn't work at full resolution
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Microsoft
 
|LifeCam Studio/Cinema
 
|
 
|
 
|
 
|
 
|
 
| Has UVC issues detailed here [http://www.ideasonboard.org/uvc/#devices]. Horizontal lines problem [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=63&t=12304]. Stability issues [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=63&t=12247].
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Microsoft
 
|Xbox Live Vision
 
|
 
| 045e:0294
 
| Arch Linux
 
|
 
|
 
| Powered by RasPi
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Sony
 
| Playstation Eye for PS3
 
|
 
|
 
|
 
|
 
|
 
| The occasional frame is corrupted/stutters when running at 640x480
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Sony
 
| Playstation Eye for PS2
 
|
 
|
 
|
 
|
 
|
 
| Occasional 'mangled frame' directly connected to Rev 2 Raspberry P
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Sony
 
| Playstation Eye for PS2
 
| SLEH 00030
 
|
 
| Arch Linux
 
|
 
|
 
| (OV519 camera). Picture constantly breaks up on xawtv and wxcam under Arch Linux. Noted there were ISOC data error len=0 status=-4004 errors in dmesg. This happens when powered from the Raspberry Pi and when powered from a Pluscom USB hub. Arch was updated on 17th July 2012
 
 
 
|- valign="top" align="left" style="background: #F5FAFF;"
 
|Trust
 
| 2 MP Auto Focus Webcam
 
|
 
|
 
| Arch Linux
 
|
 
|
 
| works out of the box
 
 
 
|- valign="top" align="left" style="background: #F6D2CF;"
 
|Trust
 
| SPACEC@M 200
 
|
 
|
 
| Arch Linux
 
|
 
|
 
| (OV511 camera). Picture stops after a few seconds in xawtv under Arch Linux and xawtv reports libv4l2 errors. This happens when powered from the Raspberry Pi and when powered from a Pluscom USB Hub. Arch was updated on 17th July 2012
 
 
 
 
 
|-
 
|}
 
  
 
== USB GPS devices ==
 
== USB GPS devices ==
Line 1,933: Line 227:
 
** Columbus V-800 (MediaTek (MTKII) 3329 GPS chipset) - does not require powered USB hub. Works on Wheezy (using gpsd & gpsd-clients)
 
** Columbus V-800 (MediaTek (MTKII) 3329 GPS chipset) - does not require powered USB hub. Works on Wheezy (using gpsd & gpsd-clients)
 
*Royaltek
 
*Royaltek
**Royaltek RGM 2000 SiRF2 using the included serial (TTL) to USB - converter. That uses a Profilic pl2303-chip so you'll need to compile the module or the kernel manually
+
**Royaltek RGM 2000 SiRF2 using the included serial (TTL) to USB - converter (Prolific pl2303-chip)
 
*Garmin
 
*Garmin
 
**Garmin eTrex Vista HCx: It works, but it may draw too much power. To get it working (software part): https://wiki.openstreetmap.org/wiki/USB_Garmin_on_GNU/Linux
 
**Garmin eTrex Vista HCx: It works, but it may draw too much power. To get it working (software part): https://wiki.openstreetmap.org/wiki/USB_Garmin_on_GNU/Linux
 
*GlobalSat
 
*GlobalSat
 
**GlobalSat BU-353 Does not require a powered hub, works fine when directly plugged into the Raspberry Pi. On Raspian, requires the gpsd and gpsd-client packages. For some reason, the gpsd daemon does not always start correctly on boot. You may need to do something like the following to manually restart it:<br /><pre>sudo killall gpsd; sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock</pre>
 
**GlobalSat BU-353 Does not require a powered hub, works fine when directly plugged into the Raspberry Pi. On Raspian, requires the gpsd and gpsd-client packages. For some reason, the gpsd daemon does not always start correctly on boot. You may need to do something like the following to manually restart it:<br /><pre>sudo killall gpsd; sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock</pre>
 +
**GlobalSat BU-353-S4 supports two protocols: NMEA, and SiRF v4.  NMEA works fine, but SiRF v4 isn't compatible with "gpsd"'s SiRF v3 interpreter, resulting in a greatly reduced data rate (as low as four location fixes per hour).  To keep "gpsd"'s autoconfiguration from putting the receiver in SiRF mode, you'll need to pass the "-b" flag when starting "gpsd".
  
 
*Wintec
 
*Wintec
Line 1,945: Line 240:
 
*Bluenext
 
*Bluenext
 
**Bluenext BN903S: No problem on Debian image (19-04-2012).
 
**Bluenext BN903S: No problem on Debian image (19-04-2012).
 +
 +
* U blox NEO 6 - works well, connects via GPIO (serial console). Info [http://diydrones.com/profiles/blogs/how-to-connect-3dr-gps-ublox-to-raspberry-pi here] and [https://github.com/petervojtek/diy/wiki/GPS-U-blox-NEO-6-with-Raspberry-Pi here].
  
 
== USB UART and USB to Serial (RS-232) adapters ==
 
== USB UART and USB to Serial (RS-232) adapters ==
 
A USB UART adapter is used to access the serial console of the Raspberry Pi from a development host such as a laptop or desktop PC.  The USB end connects to the PC and the UART header end connects to the USB.  While it is possible to connect the USB end to another Raspberry Pi, this configuration has not been tested unless explicitly mentioned against an individual entry below.
 
A USB UART adapter is used to access the serial console of the Raspberry Pi from a development host such as a laptop or desktop PC.  The USB end connects to the PC and the UART header end connects to the USB.  While it is possible to connect the USB end to another Raspberry Pi, this configuration has not been tested unless explicitly mentioned against an individual entry below.
  
*'''FTDI'''
+
===Working USB to Serial Adapters===
 +
*'''FTDI (Future Technology Devices International Limited)'''
 
**FT232 chip based adapters works for some people, but others find it hangs Linux when the port is opened. The module is ftdi_sio.
 
**FT232 chip based adapters works for some people, but others find it hangs Linux when the port is opened. The module is ftdi_sio.
 +
**FT232R USB UART works out of the box between Raspbian Wheezy and OS X Mavericks (Product-ID: 0x6001, Manufacturer-ID: 0x0403, Maximal Speed: 12 MBit/s, Maximal Power Consumption: 90 mA).
 +
**FT2232D dual RS232/FIFO works (used in various JTAG devices)
  
** FT2232D dual RS232/FIFO works (used in various JTAG devices)
+
*'''Belkin'''
 +
** F5U409 Works OOTB; does not support speeds above 115,200, so you can't use it for DMX or other high-speed protocols.
  
 
*'''Prolific'''
 
*'''Prolific'''
**PL2303 chip based adaptors works fine on latest Debian tested with ''minicom'' and ''gtkterm''
+
**PL2303 chip based adaptors works fine on latest Debian tested with ''minicom'', ''gtkterm'' and ''screen''.
  
 
A USB to Serial (RS-232) adapter is used the other way around, ie. the USB end connects to the Raspberry Pi and the RS-232 end (DSUB-9 or DSUB-25 pin) to the other device which may be another computer, (old) modem or printer, or some electronic test equipment.
 
A USB to Serial (RS-232) adapter is used the other way around, ie. the USB end connects to the Raspberry Pi and the RS-232 end (DSUB-9 or DSUB-25 pin) to the other device which may be another computer, (old) modem or printer, or some electronic test equipment.
Line 1,961: Line 262:
 
*"Best Connectivity" (Possibly also sold under the "Newlink HQ" or "Kenable HQ" labels)
 
*"Best Connectivity" (Possibly also sold under the "Newlink HQ" or "Kenable HQ" labels)
 
**FG-U1232-PL2 Based upon the Prolific PL2303X chipset and listed by ''lsusb'' as <code>ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port</code>. Appears as <code>/dev/ttyUSB0</code>, and requires the user to be a member of the ''dialout'' group (which ''pi'' is for ''Raspbian Wheezy''). Initially tested using an old RS Datalinker setup in "loopback" mode via ''microcom'' upto 9600 baud, and ''gtkterm'' after installing that from source code. All handshake lines toggled as expected and no characters were lost. Subsequently ''gtkterm'' was used to check bi-directional communication with an ancient brother EP44 electronic typewriter (as a printer/dumb terminal) at 1200 baud. Signal lines were again monitored with the Datalinker.
 
**FG-U1232-PL2 Based upon the Prolific PL2303X chipset and listed by ''lsusb'' as <code>ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port</code>. Appears as <code>/dev/ttyUSB0</code>, and requires the user to be a member of the ''dialout'' group (which ''pi'' is for ''Raspbian Wheezy''). Initially tested using an old RS Datalinker setup in "loopback" mode via ''microcom'' upto 9600 baud, and ''gtkterm'' after installing that from source code. All handshake lines toggled as expected and no characters were lost. Subsequently ''gtkterm'' was used to check bi-directional communication with an ancient brother EP44 electronic typewriter (as a printer/dumb terminal) at 1200 baud. Signal lines were again monitored with the Datalinker.
 +
* "PL2303HX USB to RS232 TTL Converter Adapter Module" on dx.com: http://dx.com/p/pl2303hx-usb-to-rs232-ttl-converter-adapter-module-164590
 +
** Based on the Prolific PL-2303HX chipset. Listed by ''lsusb'' as <tt>ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port</tt>. Appears as <tt>/dev/ttyUSBX</tt> with GUID <tt>dialout</tt> so your user has to be in that group. If not, <tt>sudo usermod -a -G dialout yourusername</tt> will add your user to the <tt>dialout</tt> group. Works great with <tt>screen /dev/ttyUSBX 115200</tt> to connect from your workstation to your RPi.
 +
 +
===Problem USB to Serial Adapters===
 +
'''HL-340'''
 +
*CH340 Chipset - '''Currently not supported by RPi''' but there is a patch of kernel code [http://tiagovaz.wordpress.com/2008/01/04/using-a-hl-340-usb-serial-adapter-against-2623-linux-kernel/ here], but it is for a 2.X kernel. If you find you have bought one of these, then it may work under Windows, but as of writing there is no support for RPi. Otherwise you can have a go at getting the patch to work.
 +
 +
== USB Multi-Card Readers ==
 +
 +
=== Working USB Multi-Card Readers ===
 +
* US Robotics USB 3.0 All-In-One Multi-Format Card Reader (Product # USR8420) Accepts 5 cards simultaneously
 +
** SD/MMC + MS/MS PRO or DUO/DUO PRO + CF/MD + SM + SD/MMC or MS/MS PRO. Useful for backing up cards containing other OS Distros
 +
 +
*'''Generic''' (Nintendo branded)
 +
**identified as "14cd:8123 Super Top SD MMC Reader" (B)
 +
 +
=== Problem USB Multi-Card Readers ===
 +
 +
*'''Generic'''
 +
**Card reader based on NEODIO ND3260-LD chip, identified as "0aec:3260 Neodio Technologies Corp. 7-in-1 Card Reader", fails after a few seconds with all access lights blinking.  (B)
 +
 +
== USB Smart-Card Readers ==
 +
 +
=== Working USB Smart-Card Readers ===
 +
* [https://www.vasco.com/ Vasco] [https://www.vasco.com/products/client_products/card_reader_digipass/digipass_905.aspx DIGIPASS 905]. Works out of the box without any extra drivers. Does not require powered USB hub.
  
 
== Other, exotic USB devices ==
 
== Other, exotic USB devices ==
 +
=== Joysticks / Joypads ===
 +
*'''Microsoft'''
 +
**Xbox360 Controller (045e:028e): works. Tested with archlinux, connected to an USB Hub, used as "mouse" in X, package xf86-input-joystick
 +
 +
*'''Logitech'''
 +
** Dual Action: works, connected directly to the Pi.
 +
 +
*'''Ion'''
 +
** Go Pad: works. Tested on Raspbian Wheezy (release 2014-01-07), connected to on-board USB port (Model B rev. 2).
 +
 +
*'''VZTEC'''
 +
** USB Double Shock Controller Game Pad Joystick VZ-GA6002: works. Tested on RetroPie V2.3, connected to on-board USB port (Model B+).
 +
 +
=== Numpads ===
 +
*'''Conceptronic / Holtek'''
 +
**USB numpad (04d9:a02a): works. Tested with archlinux, connected to an USB Hub
 +
*'''Speedlink  SL-7430-SGY'''
 +
**USB numpad (04d9:1603, HT82M99E Holtek chip inside): works. Tested with Raspbian “wheezy”
 +
*'''GreenAsia Inc. ([http://img.dxcdn.com/productimages/sku_26083_1.jpg USB 18-Key Silicone Numeric Keypad])'''
 +
**USB numpad (0e8f:0022): works. Tested with Raspbian “wheezy”
 +
 
=== USB to Parallel Port/Printer Adapters ===
 
=== USB to Parallel Port/Printer Adapters ===
 
*'''Prolific'''
 
*'''Prolific'''
 
**PL2305 Chipset with Centronics 36w connector. Originally purchased for use with a netbook and connected to an old Canon BJC-250 printer. Worked fine under [[RPi_Distributions#RISC_OS| RISC OS Raspberry Pi]] with its in-built BJC-250 driver. Could not install the CUPS drivers etc. for Wheezy-Raspbian initially, but was able to do so for Wheezy-armel. Once I'd updated/upgraded Wheezy all was fine.(See notes at [http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBtoParPrntAdapter.html CPM-Spectre-Pi...USBtoParPrntAdapter] for more info. and also a [http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/WheezyCUPS.html CUPS/Wheezy installation guide])
 
**PL2305 Chipset with Centronics 36w connector. Originally purchased for use with a netbook and connected to an old Canon BJC-250 printer. Worked fine under [[RPi_Distributions#RISC_OS| RISC OS Raspberry Pi]] with its in-built BJC-250 driver. Could not install the CUPS drivers etc. for Wheezy-Raspbian initially, but was able to do so for Wheezy-armel. Once I'd updated/upgraded Wheezy all was fine.(See notes at [http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBtoParPrntAdapter.html CPM-Spectre-Pi...USBtoParPrntAdapter] for more info. and also a [http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/WheezyCUPS.html CUPS/Wheezy installation guide])
  
=== USB to SATA ===
+
=== USB to IDE/SATA ===
 +
*'''JMicron Technology'''
 +
** JM20337 USB to SATA/PATA Combo Bridge (152d:2338) - works on Raspbian and Arch. The hard drive requires an external power supply.
 
*'''Nippon Labs'''
 
*'''Nippon Labs'''
** 2.5" SATA HDD USB Adapter with silicone HDD sleeve. Model: USB-ADT-25SATA. Works on powered Hub, not directly to Raspberry Pi. Built-in "Y" power adapter.
+
** 2.5" SATA HDD USB Adapter with silicone HDD sleeve. Model: USB-ADT-25SATA. Works on powered Hub, not directly to Raspberry Pi. Built-in "Y" power adapter. Does work direct on some ver2.0 boards if used with 5.25 power supply, or Y adapter
  
 
=== CAN Bus ===
 
=== CAN Bus ===
 
*PEAK-System (www.peak-system.com)
 
*PEAK-System (www.peak-system.com)
 
**PCAN-USB using the driver (kernel module) from http://www.peak-system.com/fileadmin/media/linux/index.htm
 
**PCAN-USB using the driver (kernel module) from http://www.peak-system.com/fileadmin/media/linux/index.htm
 +
 
=== Home automation ===
 
=== Home automation ===
 
*Tellstick (www.telldus.com), installation [[R-Pi_Tellstick_core|instructions]]
 
*Tellstick (www.telldus.com), installation [[R-Pi_Tellstick_core|instructions]]
 
**Depends on libftdi1
 
**Depends on libftdi1
 +
 +
=== Weather station ===
 +
*Oregon Scientific WMRS-200 : Work out of the box (tested with Raspbian & wview)
 +
 +
=== One-Wire ===
 +
*'''PCsensor'''
 +
**USB9097 (1a86:7523): works out of the box but issue with LAN after a few hours, no problem after a firmware update. Identify's as "QinHeng Electronics HL-340 USB-Serial adapter" Tested with raspbian/wheezy + domotiga & digitemp directly to USB port & 4 sensors connected via a '1-wire hub'. Claims to be 'fully replace DS9097, DS9490 of MAXIM'. Simple and cheap solution to measure temperature.
  
 
=== Touch Screen ===
 
=== Touch Screen ===
*ACER T230H touch screen [http://support.acer.com/acerpanam/monitor/2009/acer/t230h/t230hnv.shtml]
+
*ACER T230H touch screen [http://support.acer.com/acerpanam/monitor/2009/acer/t230h/t230hnv.shtml]This link is Broken
 
**USB TS identifies as "Quanta Computer, Inc. Optical dual-touch panel", module hid_quanta
 
**USB TS identifies as "Quanta Computer, Inc. Optical dual-touch panel", module hid_quanta
 
**Seems to draw over 200&nbsp;mA from USB!
 
**Seems to draw over 200&nbsp;mA from USB!
 +
*SainSmart 3.2 touch screen [http://www.sainsmart.com/sainsmart-3-2-tft-lcd-display-touch-panel-pcb-adapter-sd-slot-for-arduino-2560.html]
 +
**320*240
 +
**3.2 inch
 +
**SSD1289:240 RGB x 320 TFT Drive
 +
**Video: Raspberry Pi with a 3.2" TFT with Touch control [http://www.youtube.com/watch?feature=player_embedded&v=QKxmPdUoNQU]
 +
**Tutorial: Raspberry Pi with a 3.2″ TFT with Touch control [http://marks-space.com/2013/05/23/raspberry-pi-with-a-3-2-tft-with-touch-control/]
 +
 
=== Floppy Disk Drive ===
 
=== Floppy Disk Drive ===
 
*Samsung USB Floppy Drive SFD-321U/HP
 
*Samsung USB Floppy Drive SFD-321U/HP
Line 1,993: Line 357:
 
**To remove drive, ensure no sessions have the floppy directory as the current working directory.
 
**To remove drive, ensure no sessions have the floppy directory as the current working directory.
 
**sudo umount /media/floppy
 
**sudo umount /media/floppy
 +
*Y-E Data model HU-35EF
 +
**Requires a powered hub and manual mounting/unmounting like the Samsung drive above.
 +
 
=== USB Missile Launcher ===
 
=== USB Missile Launcher ===
 
*USB Missile Launcher / Rocket Launcher sold in UK by Marks and Spencer, but it is also sold under a range of other names.
 
*USB Missile Launcher / Rocket Launcher sold in UK by Marks and Spencer, but it is also sold under a range of other names.
 
**USB ID 1130:0202 Tenx Technology, Inc. Use apt-get install pymissile (python code) and there is C code at [http://sourceforge.net/projects/usbmissile/ usbmissile from Source Forge]
 
**USB ID 1130:0202 Tenx Technology, Inc. Use apt-get install pymissile (python code) and there is C code at [http://sourceforge.net/projects/usbmissile/ usbmissile from Source Forge]
 +
 
=== USB Docking Stations ===
 
=== USB Docking Stations ===
 
*StarTech USB 3.0 to Dual 2.5"/3.5" SATA HDD Dock (SATDOCK2U3GB)
 
*StarTech USB 3.0 to Dual 2.5"/3.5" SATA HDD Dock (SATDOCK2U3GB)
 
**This is an externally powered dual sata HDD docking station, which has USB2.0 compatibility with the Raspberry Pi.  
 
**This is an externally powered dual sata HDD docking station, which has USB2.0 compatibility with the Raspberry Pi.  
 
**Tested with latest Raspbmc and Debian Wheezy Raspbian,  3.1.9+ #168
 
**Tested with latest Raspbmc and Debian Wheezy Raspbian,  3.1.9+ #168
 +
 +
*Icy Box USB 3.0 to Dual 2.5"/3.5" SATA HDD Dock (IB-120StU3)
 +
**Externally powered dual HDD dock, USB 2 compatible.
 +
**Tested with Slackware ARM 14.0 and drives in both slots, just show up as separate SCSI disks.
 +
 
=== USB RFID Reader ===
 
=== USB RFID Reader ===
 
*Unbranded 125&nbsp;kHz EM4100 RFID reader from eBay sellers (< £7), the one with a Windows logo on (easily scratches off for Linux users).
 
*Unbranded 125&nbsp;kHz EM4100 RFID reader from eBay sellers (< £7), the one with a Windows logo on (easily scratches off for Linux users).
 
**Initially would not work when plugged in directly to Raspberry Pi. Worked when connected via an unpowered Trust hub. Worked after Raspberry Pi was modified with 10K resistors over the USB polyfuses (warranty invalidated). Probably would work fine with powered hub.
 
**Initially would not work when plugged in directly to Raspberry Pi. Worked when connected via an unpowered Trust hub. Worked after Raspberry Pi was modified with 10K resistors over the USB polyfuses (warranty invalidated). Probably would work fine with powered hub.
 
**Sends a 10 digit string to current window or console as if it was a keyboard. Can be captured independently of keyboard using Linux event interface (/dev/input), but the kernel in current distributions does not have CONFIG_INPUT_EVDEV selected so kernel rebuild is necessary.
 
**Sends a 10 digit string to current window or console as if it was a keyboard. Can be captured independently of keyboard using Linux event interface (/dev/input), but the kernel in current distributions does not have CONFIG_INPUT_EVDEV selected so kernel rebuild is necessary.
 +
 
=== JTAG ===
 
=== JTAG ===
 
* FTDI2232D dual RS232/FIFO based JTAG (e.g. SheevaPlug JTAGKey USB-ID 9e88:9e8f)
 
* FTDI2232D dual RS232/FIFO based JTAG (e.g. SheevaPlug JTAGKey USB-ID 9e88:9e8f)
 
** works using the Raspberry Pi as a development host
 
** works using the Raspberry Pi as a development host
=== USB 3.0 Multi-Card Reader ===
+
 
* US Robotics All-In-One Multi-Format Card Reader (Product # USR8420) Accepts 5 cards simultaneously
+
=== Tinkerforge Bricks and Bricklets (http://www.tinkerforge.com) ===
** SD/MMC + MS/MS PRO or DUO/DUO PRO + CF/MD + SM + SD/MMC or MS/MS PRO. Useful for backing up cards containing other OS Distros
+
* Read out sensors and control motors over USB with open source hardware.
 +
* Tested with the brickd_armhf.deb from [[http://www.tinkerforge.com/doc/Downloads.html#tools: here]] with:
 +
** sudo apt-get install libusb-1.0-0 libudev0
 +
** wget http://download.tinkerforge.com/tools/brickd/linux/brickd_linux_latest_armhf.deb
 +
** sudo dpkg -i brickd_linux_latest_armhf.deb
 +
* Tested languages: C/C++, C# (mono), [[Free Pascal]] ([[Lazarus]]), Java, PHP, Python, Ruby (see [[http://www.tinkerforge.com/doc/Software/API_Bindings.html: here]] for installation).
 +
* If a big amount of Bricks is used, a powered USB Hub may be required.
 +
 
 +
=== Thermometers ===
 +
 
 +
* TEMPer1 (id: 0c45:7401)
 +
** works out of the box on raspbian/wheezy with [https://github.com/petervojtek/usb-thermometer pcsensors library]
 +
 
 +
=== Fingerprint Scanners ===
 +
==== Futronic ====
 +
 
 +
Single finger scanners Futronic FS80 and FS88 tested - they work well with Raspbian. Example of captured fingerprint here: [[Media:Futronic_fingerprint_example.png]]
 +
 
 +
To make it working deploy the Futronic libScanAPI on your Raspberry Pi (example code and instructions included): [[Media:ScanApi_armlinux_RPi_gnueabihf_gcc472_update1.zip ‎]]
 +
 
 +
UPDATE:
 +
Futronic has released an updated API. This works with their newer 'H' model scanners (updated CMOS). This means the FS80H and FS81 (the OEM version of the FS80H) will now work with the RPi (I tested this myself).
 +
[[Media:ScanAPI_v823_armlinux_libusb0.1.12-bcm2708_gnueabihf_raspbian-472.zip]]
  
 
== PS2 / AT to USB Converters ==
 
== PS2 / AT to USB Converters ==
Line 2,016: Line 412:
 
Note that although the adapter might work, PS/2 keyboards were not designed to be low power USB devices, so they might not meet the requirement to work with considerable lowered supply voltage (4.4 volt) provided by the USB ports of the raspberry PI. These keyboards should work when powered by a powered hub.   
 
Note that although the adapter might work, PS/2 keyboards were not designed to be low power USB devices, so they might not meet the requirement to work with considerable lowered supply voltage (4.4 volt) provided by the USB ports of the raspberry PI. These keyboards should work when powered by a powered hub.   
  
'''Tested PS2/AT keybords'''
+
'''Tested PS2/AT keyboards'''
  
 
All above tested with the famous "blue cube" on a powered USB hub.
 
All above tested with the famous "blue cube" on a powered USB hub.
Line 2,022: Line 418:
 
*IBM Model F (please note requires an additional AT to PS2 converter)
 
*IBM Model F (please note requires an additional AT to PS2 converter)
 
*Dell AT101w
 
*Dell AT101w
*Northgate Ominikey Ultra T (please note requires an aditonal AT to PS2 converter)
+
*Northgate Ominikey Ultra T (please note requires an additional AT to PS2 converter)
  
 
* 04d9:1400 Holtek Semiconductor, Inc. PS/2 keyboard + mouse controller
 
* 04d9:1400 Holtek Semiconductor, Inc. PS/2 keyboard + mouse controller
 
** Working: Ipex RT215KTW PS/2 keyboard
 
** Working: Ipex RT215KTW PS/2 keyboard
 
** Not working: HP SK-2502 PS/2 keyboard (gets power, but it does not init - three LEDs remain permanently lit. Keyboard + Holtek converter work on a Linux PC, although this keyboard doesn't work with some native PS/2 ports.)
 
** Not working: HP SK-2502 PS/2 keyboard (gets power, but it does not init - three LEDs remain permanently lit. Keyboard + Holtek converter work on a Linux PC, although this keyboard doesn't work with some native PS/2 ports.)
 +
 +
== Power Switches ==
 +
The Raspberry Pi does not have a power on/off switch as standard (it does have a reset switch), however some add on boards have been developed to cater for this need.
 +
 +
* The [http://www.pi-supply.com/product/pi-supply-raspberry-pi-power-switch/ Pi Supply Switch]  is an  on/off power switch for the Raspberry Pi which includes a hard on and off switch and a soft shutdown switch for the Pi, making it easy to manage power on your Pi. They were recently successfully funded on Kickstarter.
 +
* '''RemotePi Board'''
 +
** The [http://www.msldigital.com/products/remotepi-board RemotePi Board] is an intelligent infrared remote controlled power switch add-on board for the Raspberry Pi. It allows to switch power on and off using any button (configurable in learning mode) of an existing standard IR remote. Power is only cut after notifying the OS and giving it time to shut-down.  It is mainly intended to remote control (using LIRC) and power off/on a mediacenter system. i.e OpenELEC, Raspbmc, XBian, RasPlex, Raspbian. The board is compatible to simple GPIO IR receiver and piggy backs onto the Raspberry Pi, no soldering required. For more information click [http://www.msldigital.com/pages/more-information here].
  
 
== Power adapters ==
 
== Power adapters ==
The Raspberry Pi uses a standard Micro USB (type B) power connector, which runs at 5&nbsp;V. Generally you can use a MicroUSB to USB cable and then either power the Raspberry Pi directly from your main computers USB ports (if they provide enough power), or by using a USB to Mains adaptor. A number of mobile phones use MicroUSB power cables, and these are compatible with the Raspberry Pi in most cases. Below is a list of power adaptors known to work.
+
The Raspberry Pi uses a standard Micro USB (type B) power connector, which runs at 5&nbsp;V. Generally you can use a MicroUSB to USB cable and then either power the Raspberry Pi directly from your main computers USB ports (if they provide enough power), or by using a USB to Mains adapter. A number of mobile phones use MicroUSB power cables, and these are compatible with the Raspberry Pi in most cases. Below is a list of power adapters known to work.
 +
 
  
 
===Working power Adapters===
 
===Working power Adapters===
 +
There is now a 5.25V 1500mA power supply manufactured ''specially'' for the Raspberry Pi to account for voltage drop due to the high current draw of the Raspberry Pi when compared to typical (phone charging etc.) duties. <br> Available in UK, EU, USA and AU varieties from [http://thepihut.com/collections/raspberry-pi-power-supplies Pi Hut] and [http://www.pi-supply.com/product-category/raspberry-pi-power-supplies/ Pi Supply]
 +
 +
 
* '''Adafruit'''
 
* '''Adafruit'''
** 5.25 V 1 A Model 501 (Newark 44W4932) USB 110-240 VAC power supply [4.99-5.00 V @ T1/T2 with 100 mA BT and/or mini wireless-n on rev 2.0 RPi USB ports]
+
** 5.25 V 1 A Model 501 (Newark 44W4932) USB 110-240 VAC power supply [4.99-5.01 V @ T1/T2 with 100 mA BT and/or mini wireless-n on RPi USB ports]
 
* '''AlcaPower'''
 
* '''AlcaPower'''
 
** 5&nbsp;V 2.5&nbsp;A Model AP5A - Charger/switching with 7 connectors(also Microusb)
 
** 5&nbsp;V 2.5&nbsp;A Model AP5A - Charger/switching with 7 connectors(also Microusb)
 
* '''Ansmann'''
 
* '''Ansmann'''
*** Dual USB charger slim, Model-Nr. 1201-0001
+
** Dual USB charger slim, Model-Nr. 1201-0001
* '''Apple'''
+
* '''Apple'''<br>Note that apple designs its charger products to work optimally as '''chargers'''. In practice this means that apple chargers drop their output voltages somewhat with output current, so that the charging circuits do not need to dissipate more heat than is strictly necessary. Because of this, and although many people have reported apple products to power their basic PI setup reliably, its still not an optimal choice for a PI system that uses power hungry USB devices. Also, because of the popularity and high price of these chargers there are many very sub standard, but almost impossible to recognize as fake copies on the market, and some of these fakes are about the worst things you can try to power your PI with! Not only do they not work, they may actually be dangerous to use!
 
** 5&nbsp;V 2.1&nbsp;A USB charger for iPad2, model A1357
 
** 5&nbsp;V 2.1&nbsp;A USB charger for iPad2, model A1357
 
** 5&nbsp;V 1.0&nbsp;A USB Charger for iPod
 
** 5&nbsp;V 1.0&nbsp;A USB Charger for iPod
Line 2,045: Line 452:
 
** 5&nbsp;V 0.85&nbsp;A USB charger for Kindle
 
** 5&nbsp;V 0.85&nbsp;A USB charger for Kindle
 
** 5&nbsp;V 2&nbsp;A Mains to USB A adaptor, Branded "CostMad"  
 
** 5&nbsp;V 2&nbsp;A Mains to USB A adaptor, Branded "CostMad"  
 +
* '''Artwizz'''
 +
** 5&nbsp;V 1.0&nbsp;A USB charger (Model: YFAR23073001)
 
* '''Asus'''
 
* '''Asus'''
 
** 5&nbsp;V 2.0&nbsp;A USB charger for Google Nexus 7
 
** 5&nbsp;V 2.0&nbsp;A USB charger for Google Nexus 7
 +
* '''Bandridge'''
 +
** 5&nbsp;V 1.0&nbsp;A Mobile Phone Charger (Model: BPC3102EC)
 
* '''Belkin'''
 
* '''Belkin'''
 
** 5&nbsp;V 2.6&nbsp;A 4 port Ultra-Slim Desktop hub (Model F4U040) (Raspberry Pi running from USB hub port)
 
** 5&nbsp;V 2.6&nbsp;A 4 port Ultra-Slim Desktop hub (Model F4U040) (Raspberry Pi running from USB hub port)
Line 2,054: Line 465:
 
** Mini Surge Protector Dual USB Charger (Model BZ103050-TVL)
 
** Mini Surge Protector Dual USB Charger (Model BZ103050-TVL)
 
** Universal USB Wall Charger (5&nbsp;V 1&nbsp;A) (Model F8Z222uk)
 
** Universal USB Wall Charger (5&nbsp;V 1&nbsp;A) (Model F8Z222uk)
 +
** Universal Home Charger with Micro USB ChargeSync Cable (10 Watt/ 2.1 Amp) F8M667tt04 [http://www.belkin.com/us/F8M667-Belkin/p/P-F8M667/ link]
 
* '''Blackberry'''
 
* '''Blackberry'''
 
** Charger for Pearl Flip 8220, Bold 9600 (B)
 
** Charger for Pearl Flip 8220, Bold 9600 (B)
 
** Charger for Tour 9630
 
** Charger for Tour 9630
 +
** 5V 1.8A "Folding Blade" Micro USB Tablet charger Part #: HDW-34724-001 Model #: AD8213HF (works with model A w/ camera + Wifi)
 
** 5&nbsp;V 0.7&nbsp;A Model PSM04R-0500CHW1(M), RIM Part Number HDW-17957-003 (B)
 
** 5&nbsp;V 0.7&nbsp;A Model PSM04R-0500CHW1(M), RIM Part Number HDW-17957-003 (B)
 
** 5&nbsp;V 750&nbsp;mA Model RIM-C-0004aDUUUC-001, RIM Part Number HWD-24481-001 (comes with Blackberry 9300)
 
** 5&nbsp;V 750&nbsp;mA Model RIM-C-0004aDUUUC-001, RIM Part Number HWD-24481-001 (comes with Blackberry 9300)
Line 2,062: Line 475:
 
** 5&nbsp;V 2&nbsp;A Model PSAC10R-050QT, RIM Part Number HDW-34725-001
 
** 5&nbsp;V 2&nbsp;A Model PSAC10R-050QT, RIM Part Number HDW-34725-001
 
** 5&nbsp;V 550&nbsp;mA curve 8520 charger works with raspberry pi Model B Board v. BS1233. It does not work with Raspbmc image.Symtoms are frequent key board and external hdd disconnects.
 
** 5&nbsp;V 550&nbsp;mA curve 8520 charger works with raspberry pi Model B Board v. BS1233. It does not work with Raspbmc image.Symtoms are frequent key board and external hdd disconnects.
 +
* '''CoolPad'''
 +
** Model: CYSK10-050200 fast charger with 5V 2000mA output, tested with USB WiFi, USB flash drive and USB wireless KB&MS connected. RPi users in China mainland can use this power adapter.<br>Encounters power loss when 4-port USB 3.0 hub is connected.
 
* '''Deal Extreme'''
 
* '''Deal Extreme'''
 
** [http://dx.com/p/5v-2a-regulated-switching-power-supply-110-220v-94518 S-10-5 5&nbsp;V 2&nbsp;A Regulated Switching Power Supply (110~220&nbsp;V)] (DIY: requires additional micro-USB connector and wiring)
 
** [http://dx.com/p/5v-2a-regulated-switching-power-supply-110-220v-94518 S-10-5 5&nbsp;V 2&nbsp;A Regulated Switching Power Supply (110~220&nbsp;V)] (DIY: requires additional micro-USB connector and wiring)
 
* '''Dell'''
 
* '''Dell'''
 
** USB Hub integrated in Dell monitors (B)
 
** USB Hub integrated in Dell monitors (B)
 +
* '''DLO'''
 +
** 5 V 1.0 A PowerBug (Model: SP05001000-A) Powers Pi, Wifi dongle and Webcam
 
* '''The FX Factory'''
 
* '''The FX Factory'''
** 5&nbsp;V 1&nbsp;A (1.2&nbsp;A max) AC Travel Charger Model KJ-USB Mains. Typically provides 4.9&nbsp;V at 1&nbsp;A <ref>[http://www.cpmspectre.pwp.blueyonder.co.uk/raspberry_pi/MoinMoinExport/USBPowerSupplies.html http://www.cpmspectre.pwp.blueyonder.co.uk/raspberry_pi/MoinMoinExport/USBPowerSupplies.html]</ref>
+
** 5&nbsp;V 1&nbsp;A (1.2&nbsp;A max) AC Travel Charger Model KJ-USB Mains. Typically provides 4.9&nbsp;V at 1&nbsp;A <ref>[http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBPowerSupplies.html http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBPowerSupplies.html]</ref>
 +
** 5&nbsp;V 2x1&nbsp;A Dual Charger Model TR9202-MICRO. Typically provides 4.8&nbsp;V at 1&nbsp;A per output. Can be used to power a Pi and, via a separate cable, a USB 4-port hub <ref>[http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/OtherTestedPSUs.html#FX_Factory_Dual_Charger_TR9202-MICRO http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/OtherTestedPSUs.html#FX_Factory_Dual_Charger_TR9202-MICRO]</ref>
 
* '''Garmin'''
 
* '''Garmin'''
 
** 5&nbsp;V 1&nbsp;A charger (Model: PSA105R-050Q) supplied with Garmin Edge 800 GPS. Requires a USB-A to MicroUSB-B cable. Belkin 6&nbsp;ft cable (F3U151B06) works.
 
** 5&nbsp;V 1&nbsp;A charger (Model: PSA105R-050Q) supplied with Garmin Edge 800 GPS. Requires a USB-A to MicroUSB-B cable. Belkin 6&nbsp;ft cable (F3U151B06) works.
 +
* '''Gembird'''
 +
** 5 V 2 A Universal USB Charger (Model: MP3A-UC-AC5). Test: 1080p TV (1xHDMI), USB Wi-fi adapter (1xUSB), wireless keyboard and mouse (1xUSB). Results: ~5.3V, works without any problems (own usb cable required).
 
* '''Globe Electric'''
 
* '''Globe Electric'''
 
** 2-Outlet Tap with Surge Protection and 2 USB Chargers ([http://globe-electric.com/product/2-outlet-tap-with-surge-protection-and-2-usb-chargers-grounded-white/ 46082]). Rated at 1000&nbsp;mA. 120&nbsp;V systems only.
 
** 2-Outlet Tap with Surge Protection and 2 USB Chargers ([http://globe-electric.com/product/2-outlet-tap-with-surge-protection-and-2-usb-chargers-grounded-white/ 46082]). Rated at 1000&nbsp;mA. 120&nbsp;V systems only.
Line 2,077: Line 497:
 
* '''Hama'''
 
* '''Hama'''
 
** 1000&nbsp;mA Travel Charger for Micro USB universal (barcode nr: 4 007249 935854)
 
** 1000&nbsp;mA Travel Charger for Micro USB universal (barcode nr: 4 007249 935854)
 +
* '''Hartig + Heiling GmbH & Co. KG'''
 +
** H+H SN 6 USB
 
* '''HP'''
 
* '''HP'''
 
** 5.3&nbsp;V 2&nbsp;A Charger for HP Touchpad (B)
 
** 5.3&nbsp;V 2&nbsp;A Charger for HP Touchpad (B)
Line 2,089: Line 511:
 
* '''Innergie'''
 
* '''Innergie'''
 
**15&nbsp;W Dual USB Adapter. Model: mMini AC15. Output: 5&nbsp;V, 3&nbsp;A (max per port), 15&nbsp;W max. [http://www.myinnergie.com/DuoPowerKit/specification.aspx Specification sheet]
 
**15&nbsp;W Dual USB Adapter. Model: mMini AC15. Output: 5&nbsp;V, 3&nbsp;A (max per port), 15&nbsp;W max. [http://www.myinnergie.com/DuoPowerKit/specification.aspx Specification sheet]
 +
* '''ICIDU'''
 +
** PI-707730 charger 5V 2.1A, sometimes drops current to ~1.3A during heavy use, but still enough to power the Pi.
 
* '''Kodak'''
 
* '''Kodak'''
 
** 5&nbsp;V 1&nbsp;A TESA5G1-0501200
 
** 5&nbsp;V 1&nbsp;A TESA5G1-0501200
 
** 5&nbsp;V 1.0&nbsp;A K20-AM
 
** 5&nbsp;V 1.0&nbsp;A K20-AM
 +
* '''König'''
 +
** 5&nbsp;V 1&nbsp;A PSUP-GSM01
 +
* '''Kuanten'''
 +
** Model SSA051F050100USU, 1A output
 
* '''LG'''
 
* '''LG'''
 
** 4.8&nbsp;V 1&nbsp;A Travel Adapter
 
** 4.8&nbsp;V 1&nbsp;A Travel Adapter
Line 2,108: Line 536:
 
** 5&nbsp;V 1&nbsp;A USB power supply for OYO ebook reader
 
** 5&nbsp;V 1&nbsp;A USB power supply for OYO ebook reader
 
* '''Microsoft'''
 
* '''Microsoft'''
*** Zune Zune AC Adapter v2  
+
*** Zune Zune AC Adapter v2
 +
* '''ModMyPi'''
 +
** [https://www.modmypi.com/shop/5v-2A-modmypi-raspberry-pi-power-supply 5.25V 2A HQ Raspberry Pi USB Power Supply] (Detachable USB) [5.01 - 5.07V @ T1/T2 with Wifi dongle and Wireless Mouse/Keyboard on RPi USB ports]
 
* '''Motorola'''
 
* '''Motorola'''
 
** [http://www.amazon.com/Motorola-Micro-USB-Home-Travel-Charger/dp/B004EYSKM8/ 5&nbsp;V 0.85&nbsp;A SPN5504 Charger with Cable]
 
** [http://www.amazon.com/Motorola-Micro-USB-Home-Travel-Charger/dp/B004EYSKM8/ 5&nbsp;V 0.85&nbsp;A SPN5504 Charger with Cable]
* '''Nokia'''
 
** 5&nbsp;V 1.2&nbsp;A AC-10E Charger
 
** [http://accessories.nokia.com/products/nokia-fast-usb-charger-ac-16/ 5&nbsp;V 1&nbsp;A AC-16E Charger]
 
 
* '''Noname'''
 
* '''Noname'''
 
** 5&nbsp;V 2.1&nbsp;A KMS-AC09 4 port USB charger (B) [http://www.miniinthebox.com/kms-ac09-universal-ac-adapter-for-ipad-ipad-2-iphone-white_p208568.html]
 
** 5&nbsp;V 2.1&nbsp;A KMS-AC09 4 port USB charger (B) [http://www.miniinthebox.com/kms-ac09-universal-ac-adapter-for-ipad-ipad-2-iphone-white_p208568.html]
 
** 5.2&nbsp;V 1&nbsp;A MW-3NU10GT - no cable, but this one works well (1m): [http://www.amazon.de/gp/product/B005L8VELA]
 
** 5.2&nbsp;V 1&nbsp;A MW-3NU10GT - no cable, but this one works well (1m): [http://www.amazon.de/gp/product/B005L8VELA]
 
** 5&nbsp;V 1&nbsp;A Model H-IP008 Serial No. H10T80L068
 
** 5&nbsp;V 1&nbsp;A Model H-IP008 Serial No. H10T80L068
 +
** 5&nbsp;V 1&nbsp;A Travel charger Model MSH-TR-018A [http://www.akizz.com/catalog/product/chargeur-secteur-rapide-de-voyage-70/galaxy-duos-s7562 reseller1], [http://www.sepdistribution.fr/produit-2496.html reseller2]
 +
** 5V 2A Mobile Charger For Galaxy S4 NOTE 2 N7100 N7000 With USB Cable(in India) [http://cgi.ebay.in/ws/eBayISAPI.dll?ViewItem&item=271603546214 Ebay.in]
 
* '''Novatel Wireless'''
 
* '''Novatel Wireless'''
 
** 5&nbsp;V 1.05&nbsp;A Charger, model number SSW-1811, packaged with Verizon Wireless MiFi device
 
** 5&nbsp;V 1.05&nbsp;A Charger, model number SSW-1811, packaged with Verizon Wireless MiFi device
Line 2,130: Line 559:
 
* '''Phihong'''
 
* '''Phihong'''
 
** Switching Power Supply. Model: PSAC09R-050. Output: 5&nbsp;V, 1.8&nbsp;A, microUSB.  [http://www.digikey.com/product-detail/en/PSAC09R-050/993-1109-ND/2635771 Digi-key Link]
 
** Switching Power Supply. Model: PSAC09R-050. Output: 5&nbsp;V, 1.8&nbsp;A, microUSB.  [http://www.digikey.com/product-detail/en/PSAC09R-050/993-1109-ND/2635771 Digi-key Link]
 +
* '''Pi Supply'''
 +
**  [http://www.pi-supply.com/product/uk-micro-usb-raspberry-pi-power-supply-5v-1500ma/ 5.25V 1.5A Raspberry Pi USB Power Supply] Specially designed for the Pi. Comes in 4 varieties for worldwide compatibility -  UK,  European (EU),  American (USA) and  Australian (AUS). 
 
* '''PortaPow'''
 
* '''PortaPow'''
 
** PortaPow UK Mains Wall Power Supply
 
** PortaPow UK Mains Wall Power Supply
 +
* '''PowerGen'''
 +
** PowerGen Dual Port USB 2.1A 10W AC Travel Wall Charger. [http://www.amazon.com/gp/product/B0073FCPSK Amazon Link]
 +
* '''Rayovac'''
 +
** Universal USB Charger Model: PS69 100-240 VAC to 5 V 1 A (small cube w/folding plug) works w/wireless keyboard/mouse and mini-Wifi connected
 +
* '''RhoTech'''
 +
** [http://www.rhotech.eu/index.php?id_product=10&controller=product RH-PS001] 5V/2A, dedicated for Raspberry Pi, integrated MicroUSB cable. Stable with Raspbmc and WiFi card.
 +
** [http://www.rhotech.eu/index.php?id_product=11&controller=product RH-PS002] 5V/2.1A dual USB Power Supply.
 
* '''RS Components'
 
* '''RS Components'
** HNP06UK (RS 7263069) Switching Adapter 5.0&nbsp;V 1200&nbsp;mA
+
** HNP06UK (RS 7263069) Switching Adapter 5.0&nbsp;V 1200&nbsp;mA [http://uk.rs-online.com/web/p/plug-in-power-supply/7263069]
 
* '''Samsung'''
 
* '''Samsung'''
 
** 5&nbsp;V 0.7&nbsp;A Charger for Galaxy S model ETA0U10EBE
 
** 5&nbsp;V 0.7&nbsp;A Charger for Galaxy S model ETA0U10EBE
Line 2,144: Line 582:
 
** 5&nbsp;V ?A (Unknown) Samsung Service Port (USB) on LN32A330J1DXZA 720p 32 inch HDTV  
 
** 5&nbsp;V ?A (Unknown) Samsung Service Port (USB) on LN32A330J1DXZA 720p 32 inch HDTV  
 
** 5&nbsp;V Unknown Ampere Samsung UA22D5000 & UA32D5000 TV USB Port. Test with Raspbian Wheezy, Raspbmc, and RPITC
 
** 5&nbsp;V Unknown Ampere Samsung UA22D5000 & UA32D5000 TV USB Port. Test with Raspbian Wheezy, Raspbmc, and RPITC
 +
** 5 V 2 A charger for Galaxy Note 2; model ETA-U90EWE (works with cam module, Edimax wifi, SD card and analog audio out, even down to 4.62 V on model B rev 1).
 
* '''Shun Shing'''
 
* '''Shun Shing'''
 
** 100-240&nbsp;VAC to 5&nbsp;VDC 1&nbsp;A USB power supply, model SP5Q-AU [http://jaycar.co.nz/productView.asp?ID=MP3455 Jaycar]
 
** 100-240&nbsp;VAC to 5&nbsp;VDC 1&nbsp;A USB power supply, model SP5Q-AU [http://jaycar.co.nz/productView.asp?ID=MP3455 Jaycar]
 
* '''Sony Ericsson'''
 
* '''Sony Ericsson'''
 
** 5&nbsp;V 0.7&nbsp;A Charger CST-80
 
** 5&nbsp;V 0.7&nbsp;A Charger CST-80
** 5&nbsp;V 0.85&nbsp;A Greenheart&#153; Charger EP800. Typically provides 4.8&nbsp;V at 0.85&nbsp;A <ref>[http://www.cpmspectre.pwp.blueyonder.co.uk/raspberry_pi/MoinMoinExport/USBPowerSupplies.html http://www.cpmspectre.pwp.blueyonder.co.uk/raspberry_pi/MoinMoinExport/USBPowerSupplies.html]</ref>.
+
** 5&nbsp;V 0.85&nbsp;A Greenheart&#153; Charger EP800. Typically provides 4.8&nbsp;V at 0.85&nbsp;A <ref>[http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBPowerSupplies.html http://www.cpmspectrepi.webspace.virginmedia.com/raspberry_pi/MoinMoinExport/USBPowerSupplies.html]</ref>.
 
* '''StarTech'''
 
* '''StarTech'''
 
** 4 Port USB 2.0 Hub Raspberry Pi can be powered just by plugging USB input into the Raspberry Pi, don't need power in micro USB port.
 
** 4 Port USB 2.0 Hub Raspberry Pi can be powered just by plugging USB input into the Raspberry Pi, don't need power in micro USB port.
Line 2,155: Line 594:
 
* '''Technika'''
 
* '''Technika'''
 
** 5&nbsp;V 1&nbsp;A USB Power Adapter, model MPASS01 (B)
 
** 5&nbsp;V 1&nbsp;A USB Power Adapter, model MPASS01 (B)
* '''The Pi Hut'''
+
* '''Tinpec'''
** Micro USB Power Supply for the Raspberry Pi. 5&nbsp;V 1000&nbsp;mA (from [http://thepihut.com/collections/power-supplies The Pi Hut's Raspberry Pi Store]) (also from [http://www.ebay.co.uk/itm/330757401271 eBay ])
+
** 5&nbsp;V 2&nbsp;A USB Power Adapter model RG-AAC210, sold by Elro as AV323S
 
* '''Trisonic'''
 
* '''Trisonic'''
 
** TS-CP600T - MICRO USB HOME & TRAVEL CHARGER (5&nbsp;V, 800&nbsp;mA) $3 at Daiso U.S. stores.
 
** TS-CP600T - MICRO USB HOME & TRAVEL CHARGER (5&nbsp;V, 800&nbsp;mA) $3 at Daiso U.S. stores.
 
* '''TruePower'''
 
* '''TruePower'''
 
** [http://u-socket.com/ U-Socket] 5&nbsp;V 2.1&nbsp;A AC Receptacle with Built-in USB ports (2.1&nbsp;A per USB port) model ACE-7169
 
** [http://u-socket.com/ U-Socket] 5&nbsp;V 2.1&nbsp;A AC Receptacle with Built-in USB ports (2.1&nbsp;A per USB port) model ACE-7169
 +
* '''Turnigy'''
 +
** TURNIGY [http://hobbyking.com/hobbyking/store/__4319__TURNIGY_3A_UBEC_w_Noise_Reduction.html 3A UBEC] w/ Noise Reduction, connected to GPIO Pins
 
* '''Voltcraft'''
 
* '''Voltcraft'''
 
** SPS5-12W, 2500&nbsp;mA, requires additional USB <-> miniUSB adapter/cable, works perfectly (bought from [http://www.conrad.de/ce/de/product/512660/VOLTCRAFT-SPS5-12W-Steckernetzteil-Steckernetzgeraet-5-VDC-2500-mA-12-Watt Conrad Shop])
 
** SPS5-12W, 2500&nbsp;mA, requires additional USB <-> miniUSB adapter/cable, works perfectly (bought from [http://www.conrad.de/ce/de/product/512660/VOLTCRAFT-SPS5-12W-Steckernetzteil-Steckernetzgeraet-5-VDC-2500-mA-12-Watt Conrad Shop])
 +
* '''Youse'''
 +
** Dual USB Wall Plate. Has a 2.1A "Tablet" port, a 1A "Phone" port and a US electrical outlet. Powers a Raspberry Pi 2 from the 2.1A "Tablet" port. Available from Five Below. [https://www.fivebelow.com/tech/shop-by-phone/iphone-5-reg/youse-trade-dual-usb-wall-plate.html Link]
 +
* '''ZTE'''
 +
** ZTE Blade charger STC-A22O501700USBA-A 5&nbsp;V 700&nbsp;mA
  
 
===Problem power Adapters===
 
===Problem power Adapters===
 +
* '''Nokia'''
 +
** 5&nbsp;V 1.2&nbsp;A AC-10A & AC-10E Chargers only provide 4.8V at TP1 & TP2
 +
** [http://accessories.nokia.com/products/nokia-fast-usb-charger-ac-16/ 5&nbsp;V 1&nbsp;A AC-16E Charger] Provides only 4.7V across TP1 & TP2 when at idle
 +
 
* '''Masterplug'''
 
* '''Masterplug'''
** Masterplug Surge Protected USB Adaptor 2 x 1&nbsp;A USB Polished Black - USB ports and Ethernet don't work with this adapter and some screen artefacts using HDMI.
+
** Masterplug Surge Protected USB Adaptor 2 x 1&nbsp;A USB Polished Black - USB ports and Ethernet don't work with this adapter and some screen artifacts using HDMI.
 
* '''Monoprice'''
 
* '''Monoprice'''
 
** 5&nbsp;V, 2&nbsp;A 3 Outlet Power Surge Protector Wall Tap with 2 Built-In USB Charger - some display artifacts, sometimes unable to find mouse, some failures to boot. Measured to less than 4.75&nbsp;V between TP1 and TP2 when used with a Monoprice cable.
 
** 5&nbsp;V, 2&nbsp;A 3 Outlet Power Surge Protector Wall Tap with 2 Built-In USB Charger - some display artifacts, sometimes unable to find mouse, some failures to boot. Measured to less than 4.75&nbsp;V between TP1 and TP2 when used with a Monoprice cable.
Line 2,172: Line 621:
 
** 5&nbsp;V, 850&nbsp;mA EP800. Some failures to boot, Ethernet loops at boot.
 
** 5&nbsp;V, 850&nbsp;mA EP800. Some failures to boot, Ethernet loops at boot.
  
===External Battery packs (with 5&nbsp;V regulated output)===
+
===Working external Battery packs (with 5&nbsp;V regulated output)===
* '''Anker Astro3'''
+
* '''Anker'''
** Anker Astro3 10000&nbsp;mAh with dual 2&nbsp;A USB output
+
** Astro3 10000&nbsp;mAh with dual 2&nbsp;A USB output
 +
** Astro E7 2nd Gen (A1210) 26800&nbsp;mAh with triple 4&nbsp;A USB output
 +
** PowerCore (A1271) 20100&nbsp;mAh with dual 2.4&nbsp;A USB output
 
* '''Duracell'''
 
* '''Duracell'''
 
** PPS2 Instant USB Charger
 
** PPS2 Instant USB Charger
 +
* '''EasyAcc'''
 +
** PB12000A 12000&nbsp;mAh battery with 2.1&nbsp;A USB output
 
* '''Energizer/XPAL'''
 
* '''Energizer/XPAL'''
 
** XP18000 18000&nbsp;mAh Power Pack
 
** XP18000 18000&nbsp;mAh Power Pack
Line 2,182: Line 635:
 
** 6000T Pocket Power 5000&nbsp;mAh - eBay item 271009959140
 
** 6000T Pocket Power 5000&nbsp;mAh - eBay item 271009959140
 
** Power Bank for iPad/iPhone 5000&nbsp;mAh (looks the same as a New Trent IMP50D or TeckNet iEP380) - eBay item 280914455938
 
** Power Bank for iPad/iPhone 5000&nbsp;mAh (looks the same as a New Trent IMP50D or TeckNet iEP380) - eBay item 280914455938
 +
* '''Mophie'''
 +
** 38113BBR Juice Pack Powerstation 4000 mAh: output 2.1 A max: included charging cable powers RPi, 7.5 hrs light use w/keyboard and mini-Wifi on RPi ports
 +
* '''iEnjoy'''
 +
** MyBolt 2600mAh
 
* '''New Trent'''
 
* '''New Trent'''
 
** iCurve IMP70D 7000&nbsp;mAh (Approx 12&nbsp;hours from full charge)
 
** iCurve IMP70D 7000&nbsp;mAh (Approx 12&nbsp;hours from full charge)
Line 2,189: Line 646:
 
* '''TeckNet'''
 
* '''TeckNet'''
 
** iEP387 Dual-Port 7000&nbsp;mAh External Power Bank (The charging lead can be used to connect the Tecknet to the Raspberry Pi. Ran the Raspberry Pi with Wi-Fi dongle and wireless keyboard receiver for over 9 hours of light use.)
 
** iEP387 Dual-Port 7000&nbsp;mAh External Power Bank (The charging lead can be used to connect the Tecknet to the Raspberry Pi. Ran the Raspberry Pi with Wi-Fi dongle and wireless keyboard receiver for over 9 hours of light use.)
 +
** iEP390-9000mAh External Power Bank  (The Power Bank has been verified working with RPI3 with on-board Wifi and HDMI out. Additionally, the Power Bank supplies power to RPI continuously without disruptions even when the Power Bank is connected / disconnected from charger -> it can be used as a cheap UPS)
 
** iEP392 Dual-Port 12000&nbsp;mAh External Power Bank (1&nbsp;A port, ~16.5 hours)
 
** iEP392 Dual-Port 12000&nbsp;mAh External Power Bank (1&nbsp;A port, ~16.5 hours)
 
** Rayovac PS60 5&nbsp;V 800&nbsp;mAh
 
** Rayovac PS60 5&nbsp;V 800&nbsp;mAh
Line 2,195: Line 653:
 
* '''Kodak Power Pack KP1000'''
 
* '''Kodak Power Pack KP1000'''
 
** 1&nbsp;A USB rechargeable battery pack - see [http://blog.sheasilverman.com/2012/09/its-alive/ Shea Silverman's blog]
 
** 1&nbsp;A USB rechargeable battery pack - see [http://blog.sheasilverman.com/2012/09/its-alive/ Shea Silverman's blog]
 +
* '''Swees'''
 +
** Swees® 12000mAh Smart Power Bank (Output: 5V / 4.2A max)
  
 +
== LCD touch screen add-ons ==
 
== Display adapters ==
 
== Display adapters ==
Note that active converter boxes may draw power through the HDMI port, and thus will put an extra load on your PSU, and also increase the current running through the Raspberry Pi's primary input fuse. HDMI ports (and the raspberry PI) are designed so that they deliver a very limited amount of power (50&nbsp;mA) to the TV/Monitor/display-adapter and much more isn't in theory allowed. In fact there is a diode (D1) in series with the power line which can only handle 200&nbsp;mA, if the adapter tries to draw much more than that the diode might fail. Therefore only externally powered adapters are to be recommended. Despite this, many people report success with these high powered devices.
+
Note that active converter boxes may draw power through the HDMI port, and thus will put an extra load on your PSU, and also increase the current running through the Raspberry Pi's primary input fuse. HDMI ports (and the raspberry PI) are designed so that they deliver a very limited amount of power (50&nbsp;mA) to the TV/Monitor/display-adapter and much more isn't in theory allowed. In fact there is a diode (D1) in series with the power line which can only handle 200&nbsp;mA, if the adapter tries to draw much more than that the diode might fail. Therefore only externally powered adapters are to be recommended. Despite this, many people report success with non externally powered devices. If you have bought a non externally powered HDMI to VGA adapter, and you experience problems with it (It behaves badly, D1 burns out, F3 "blows", or your PSU overloads), then not all is lost, there are cheap (a few dollars) adapters that allow you to add external power to the HDMI cable! An example can be found here: [http://dx.com/p/hdmi-male-to-hdmi-female-adapter-w-power-input-port-black-155361].
 +
 
 +
===HDMI->DVI-D cables===
 +
HDMI to DVI-D cables, or HDMI cables with an DVI-D adapters should work, connected to a DVI-D monitor, that is because both HDMI and DVI use the same kind of digital signaling (LVDS). The only limitation being that DVI-D misses the signal channel for audio.
  
===HDMI->DVI-D===
+
There are three kinds of DVI. There is DVI-D, a digital signal fully compatible with HDMI, so a passive cable can be used. There is DVI-I, which is a connector with both analog pins and digital pins. An HDMI to DVI-D adapter fits in a DVI-I female connector. Finally, there is DVI-A. This a fairly rare connection, but occasionally it will be found on some monitors and is an analog interface, in fact the same as VGA! In any case, you may need to change [[RPi_config.txt|config.txt]] hdmi_force_hotplug=0 to =1 if your display does not receive DVI signal (the analog output is likely active).
There are three kinds of DVI. There is DVI-D, a digital signal fully compatible with HDMI, so a passive cable can be used. There is DVI-I, which is a connector with both analog pins and digital pins. An HDMI to DVI-D adapter fits in a DVI-I female connector. Finally, there is DVI-A. This a fairly rare connection, but occasionally it will be found on some monitors and is an analog interface, in fact the same as VGA!
 
  
 
Some adapters like Farnell part AK-CBHD03-BK are HDMI to DVI-I, which, while not fitting in a DVI-D monitor, are still compatible. The analog pins simply must be bent.
 
Some adapters like Farnell part AK-CBHD03-BK are HDMI to DVI-I, which, while not fitting in a DVI-D monitor, are still compatible. The analog pins simply must be bent.
Line 2,211: Line 674:
 
** AmazonBasics HDMI to DVI Adapter Cable (model SK231) works and is inexpensive.
 
** AmazonBasics HDMI to DVI Adapter Cable (model SK231) works and is inexpensive.
 
** [http://www.ebay.com/itm/DVI-Female-to-HDMI-Male-Adapter-Converter-Adaptor-Gold-for-HDTV-Full-HD-/320946033059?pt=US_Video_Cables_Adapters&hash=item4ab9dfd1a3 A generic HDMI-to-DVI converter from eBay]. Works well, but it's probably the cause of some power loss between the Raspberry Pi and the monitor, causing [http://elinux.org/R-Pi_Troubleshooting#Interference_visible_on_a_HDMI_or_DVI_monitor this] problem. A setting of config_hdmi_boost='''5''' in /etc/boot solved this. Note that config_hdmi_boost='''4''', as suggested in the troubleshooting guide, helped, but it did not solve the problem completely.
 
** [http://www.ebay.com/itm/DVI-Female-to-HDMI-Male-Adapter-Converter-Adaptor-Gold-for-HDTV-Full-HD-/320946033059?pt=US_Video_Cables_Adapters&hash=item4ab9dfd1a3 A generic HDMI-to-DVI converter from eBay]. Works well, but it's probably the cause of some power loss between the Raspberry Pi and the monitor, causing [http://elinux.org/R-Pi_Troubleshooting#Interference_visible_on_a_HDMI_or_DVI_monitor this] problem. A setting of config_hdmi_boost='''5''' in /etc/boot solved this. Note that config_hdmi_boost='''4''', as suggested in the troubleshooting guide, helped, but it did not solve the problem completely.
 +
 +
===HDMI->VGA Cables===
 +
HDMI to VGA cables <strong>do not work!</strong>
 +
They rely on logic incorporated in a video card that isn't available in a PI.
 +
Somehow such a video card outputs analog signal on the otherwise purely digital HDMI connector, that seems to be the only way for it to work.
 +
But normally HDMI cables <strong>never</strong> carry analog signals and the PI surely doesn't output analog signals either, almost no HDMI output device does, as its completely against HDMI specifications.
  
 
===HDMI->VGA converter boxes===
 
===HDMI->VGA converter boxes===
 +
 +
HDMI to VGA <strong>converters</strong> do work, they convert the digital serial data streams from HDMI and using complex logic, and digital to analog converters they convert the HDMI signal to the analog signals needed for VGA, and sometimes also convert HDMI audio to an analog stereo signal. But note that if they feed off the PI it can cause a problem, as the PI only is designed to provide about 50mA to the (HDMI or DVI-D) monitor, and these adapters use >200mA, while the absolute maximum the PI can let through is 200mA.
 +
These adapters also thus use about half the energy that the PI (without USB devices) uses.
 +
Therefore its much better to use an adapter that has an external power input. Alternatively there are HDMI dongles (male to female HDMI adapters) that have a barrel input connector to feed the adapter with.
 +
 +
It seems unlikely any of these HDMI->VGA converters could be used for driving a SCART RGB SD CRT TV with a suitable lead (as shown here for ATI/Nvidia PC output http://www.mythtv.org/wiki/RGB_Scart) because they only output preset progressive resolutions, whereas the TV will need an interlaced resolution and probably custom timings.
 +
 
Most will require use [[RPi_config.txt]]. Start off with hdmi_safe=1.
 
Most will require use [[RPi_config.txt]]. Start off with hdmi_safe=1.
  
[http://www.element14.com/community/groups/raspberry-pi/blog/2012/08/16/raspberry-pi-hdmi-to-vga-converter Sanoxy HDMI to VGA converter], $27 from Amazon, no changes required with official Raspbian Wheezy image (2012-Jul-15), note: had already disabled overscan previously
+
'''HDMI to VGA + audio adapter from DHgate'''
 +
* Under six pounds with free international shipping [http://www.dhgate.com/product/hdmi-to-vga-output-projector-monitors-adapter/170509392.html] makes this worth the delivery time of just under 3 weeks.  Works out of the box at 1024x768 without editing config.txt (I'll try editing for full HD later).  Spec. says upto UXGA and 1080p with 10-bit DAC at 165MHz/1.65Gbps.  Raspberry "tvservice -a" reports that it supports audio up to 192k at 24-bit.  Sounded fine on my tiny speaker.  Comes with 3.5mm stereo plug-to-plug cable and USB to mini barrel jack power cable which it doesn't need on the Pi.  Ran mine for ages without the external power and the Pi's HDMI regulator never got more than 34 degrees C.  Adapter weighs only 14.8g and can plug directly into the Pi or even via a 90-degree 'elbow' which I prefer to use.  VGA signal is good enough to run 2 displays at once using a cheap splitter cable.  After brief testing with good headphones, it seems there's some definite noise on a signal of 17,500Hz and 18,500Hz is distorted.  In contrast, the RPi's own analogue sounds clean at 17,500Hz.  So you couldn't consider this an alternative to a good USB DAC.
 +
 
 +
'''HDMI to VGA Cable adaptor from amazon'''
 +
* At under ten pounds this one [http://www.amazon.co.uk/gp/product/B0088K7QUQ] is one of the cheapest, but perhaps due to a more advanced design is seems power frugal enough to most often work well with a Pi, it has many comments saying it works well with the Pi, and gives tips on how to edit config.txt.
 +
 
 +
'''HDMI to VGA adapter from amazon - USA'''
 +
* This one works with Pi, but does require config.txt edit.
 +
http://www.amazon.com/gp/product/B00JLRHMZE/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
 +
Ableconn HDMI2VGAD Active HDMI to VGA Adapter Converter Dongle for Desktop PC/Notebook up to 1920x1200 / 1920x1080 - HDMI to VGA HD15 monitor
 +
Price: $17.99 (Mar. 13, 2015).  One photo shows three Pi models connected to VGA monitors.
 +
The AbleComm logo is on clear tape wrapped around the adapter, apparently made for "private labeling".  So, the item is probably sold by other suppliers too.
 +
The adapter is very compact and low-power, unlike some of the other adapters.
 +
My ViewSonic VA702b monitor required:
 +
hdmi_group=2  -- indicates VGA
 +
hdmi_mode=35  -- 1280 x 1024, 60 Hz
 +
Prior to those changes, the picture color was mostly red, but readable enough to log in and edit config.txt.
  
http://www.amazon.co.uk/gp/product/B007KEIRNG -- "Neewer" HDMI to VGA -- some issues discussed below:
+
'''Sanoxy HDMI to VGA converter'''
However, according to user "Tom1989" the same Neewer HDMI to VGA adapter burned out BAT54 Schottky diode D1 on the Raspberry Pi and broke its HDMI output: [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=9819 Serious HDMI Problems. What's that smell? Burning Raspberry!].  On that thread, "mahjongg" suggested the NXP (or equivalent) PMEG2010AET as a high-current replacement for D1. The PMEG2010AET has 1&nbsp;A max forward current, much greater than the BAT54's 200&nbsp;mA limit which may be exceeded by your HDMI -> VGA converter.  Remember that the converter's current must come from your Raspberry Pi power supply and go through the Micro USB cable and polyfuse F3, so you may get extra voltage drops and/or cause F3 to trip depending on how much current the converter uses.  As always with board modifications, YMMV. Also on the "Burning Raspberry!" thread, user "pwinwood" reported the Neewer's current to be 400&nbsp;mA, which is twice the limit of BAT54 diode D1.  "pwinwood" also took the Neewer apart and added its own +5&nbsp;V connection adapted from a USB cable, which bypasses Raspberry Pi's Micro USB cable and polyfuse F3.
+
* [http://www.element14.com/community/groups/raspberry-pi/blog/2012/08/16/raspberry-pi-hdmi-to-vga-converter Sanoxy HDMI to VGA converter]'', $27 from Amazon, no changes required with official Raspbian Wheezy image (2012-Jul-15), note: had already disabled overscan previously
  
* Link to a gallery with detailed images & steps of the same adapter modification: [http://imgur.com/a/sLogs/all HERE] --''by [[User:Pinoccio|Pinoccio]]''
+
'''"Neewer" HDMI to VGA '''
 +
* http://www.amazon.co.uk/gp/product/B007KEIRNG -- "Neewer" HDMI to VGA -- some issues discussed below:
 +
According to user "Tom1989" the same Neewer HDMI to VGA adapter burned out BAT54 Schottky diode D1 on the Raspberry Pi and broke its HDMI output: [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=9819 Serious HDMI Problems. What's that smell? Burning Raspberry!].  On that thread, "mahjongg" suggested the NXP (or equivalent) PMEG2010AET as a high-current replacement for D1. The PMEG2010AET has 1&nbsp;A max forward current, much greater than the BAT54's 200&nbsp;mA limit which may be exceeded by your HDMI -> VGA converter.  Remember that the converter's current must come from your Raspberry Pi power supply and go through the Micro USB cable and polyfuse F3, so you may get extra voltage drops and/or cause F3 to trip depending on how much current the converter uses.  As always with board modifications, YMMV. Also on the same" thread, user "pwinwood" reported the Neewer's current to be 400&nbsp;mA, which is twice the limit of BAT54 diode D1.  "pwinwood" also took the Neewer apart and added its own +5&nbsp;V connection adapted from a USB cable, which bypasses Raspberry Pi's Micro USB cable and polyfuse F3.
 +
Link to a gallery with detailed images & steps of the same adapter modification: [http://imgur.com/a/sLogs/all HERE] --''by [[User:Pinoccio|Pinoccio]]''
  
http://www.amazon.co.uk/KanaaN-Adapter-Converter-Cable-Resolutions/dp/B007QT0NNW -- "Kanaan" HDMI-VGA
+
'''"Kanaan" HDMI-VGA'''
 +
* http://www.amazon.co.uk/KanaaN-Adapter-Converter-Cable-Resolutions/dp/B007QT0NNW -- "Kanaan" HDMI-VGA
  
http://www.ebay.com/itm/ws/eBayISAPI.dll?ViewItem&item=130699741793 -- eBay is swarming with $16 converters all like this one.
+
'''HDMI Male to VGA RGB Female HDMI to VGA Video Converter adapter'''
 +
* http://www.ebay.com/itm/ws/eBayISAPI.dll?ViewItem&item=130699741793 -- eBay is swarming with $16 converters all like this one.
  
This adapter -- http://www.ebay.co.uk/itm/300692770623 -- works from 640x480 up to 1920x1080, audio over HDMI works too.
+
'''HDMI to VGA 3.5mm Audio HDTV HD Video Converter'''
Sadly the IC's on the PCB have all been scrubbed.
+
* This adapter -- http://www.ebay.co.uk/itm/300692770623 -- works from 640x480 up to 1920x1080, audio over HDMI works too.
 +
Sadly the IC's on the PCB have all been scrubbed. In-depth review http://raspi.tv/2013/hdmi-to-vga-video-converter-with-sound-for-raspberry-pi-review.
 
Requires HDMI boost and overscan, [[RPi_config.txt|config.txt]] settings for 640x480 @60&nbsp;Hz:
 
Requires HDMI boost and overscan, [[RPi_config.txt|config.txt]] settings for 640x480 @60&nbsp;Hz:
<br>hdmi_drive=2
+
<pre>hdmi_drive=2
<br>hdmi_group=2
+
hdmi_group=2
<br>hdmi_mode=4
+
hdmi_mode=4
<br>config_hdmi_boost=4
+
config_hdmi_boost=4
<br>overscan_top=-30
+
overscan_top=-30
<br>overscan_bottom=-30
+
overscan_bottom=-30
<br>overscan_left=-30
+
overscan_left=-30
<br>overscan_right=-30
+
overscan_right=-30
 +
</pre>
  
According to user "Mortimer" -- HDFuryPro HDMI to YPbBr/VGA Converter found on Amazon -- http://www.amazon.co.uk/Inputs-Component-Video-YPbPr-Converter/dp/B00797ZZ4S/ -- Works with Raspberry Pi. Tested against a Philips 170B 1280x1024 LCD monitor, producing a full native resolution image. Not tested against a Component Video TV yet, and audio has yet to be got working.
+
'''HDFuryPro HDMI to YPbBr/VGA Converter'''
 +
* HDFuryPro HDMI to YPbBr/VGA Converter found on Amazon -- [http://www.amazon.co.uk/Inputs-Component-Video-YPbPr-Converter/dp/B00797ZZ4S/] -- Works with Raspberry Pi. Tested against a Philips 170B 1280x1024 LCD monitor, producing a full native resolution image. Not tested against a Component Video TV yet, and audio has yet to be got working.
 
The [[RPi_config.txt|config.txt]] settings used are:
 
The [[RPi_config.txt|config.txt]] settings used are:
<br>hdmi_drive=2
+
<pre>hdmi_drive=2
<br>hdmi_group=2
+
hdmi_group=2
<br>hdmi_mode=36
+
hdmi_mode=36
<br>disable_overscan=1
+
disable_overscan=1
 
+
</pre>
  
According to user "Mortimer" -- HDFury1 1080p HDMI to VGA Converter from HDFury.com. I'm not sure the HDFury1 can be got a hold of easily nowadays, I happened to have access to one to try out. HDFury2, 3 and 4 are available as far as I can tell, but it is very pricey compared to the alternatives. HDFury1 was around £80 when we bought one for a project at work. HDFury2 seems to be around £130, 3 and 4 are getting on towards £200 or more. So not to be recommended as a solution unless you happen to have one lying around. I don't believe there is any relationship between the company that produces these and the HDFuryPro I bought for myself (See above). I didn't alter any config settings, just plugged it in. It doesn't work without having its external power supply connected, as it requires 0.4&nbsp;A, which is too much draw for the 5&nbsp;V supply available from the HDMI socket on the Raspberry Pi. Its power LED lights, but no picture is produced. In comparison to the HDFuryPro this picture from this device is sharper, but it is not enough to justify the extra cost.
+
'''HDFury1 1080p HDMI to VGA Converter'''
 +
* HDFury1 1080p HDMI to VGA Converter from HDFury.com. I'm not sure the HDFury1 can be got a hold of easily nowadays, I happened to have access to one to try out. HDFury2, 3 and 4 are available as far as I can tell, but it is very pricey compared to the alternatives. HDFury1 was around £80 when we bought one for a project at work. HDFury2 seems to be around £130, 3 and 4 are getting on towards £200 or more. So not to be recommended as a solution unless you happen to have one lying around. I don't believe there is any relationship between the company that produces these and the HDFuryPro I bought for myself (See above). I didn't alter any config settings, just plugged it in. It doesn't work without having its external power supply connected, as it requires 0.4&nbsp;A, which is too much draw for the 5&nbsp;V supply available from the HDMI socket on the Raspberry Pi. Its power LED lights, but no picture is produced. In comparison to the HDFuryPro this picture from this device is sharper, but it is not enough to justify the extra cost.
 
The [[RPi_config.txt|config.txt]] settings used are:
 
The [[RPi_config.txt|config.txt]] settings used are:
<br>hdmi_drive=2
+
<pre>hdmi_drive=2
<br>hdmi_group=2
+
hdmi_group=2
<br>hdmi_mode=36
+
hdmi_mode=36
<br>disable_overscan=1
+
disable_overscan=1
 +
</pre>
  
http://www.amazon.co.uk/gp/product/B007SM7O2U/ref=oh_details_o02_s00_i00 - "Cable Matters"
+
'''Cable Matters Gold Plated Premium HDMI to VGA'''
 +
* http://www.amazon.co.uk/gp/product/B007SM7O2U/ - "Cable Matters"
 +
Or in the US:
 +
* http://www.amazon.com/gp/product/B00879DM56 - "Cable Matters Active HDMI to VGA Adapter"  I've seen mixed results with this one; it seems to work the very first time I try it on a given monitor, but then I can't seem to get it to work afterwards.  I've tried various combinations of the other settings shown in this section with no success.
 +
How to get working if no output:
 +
edit config.txt
 +
<pre>
 +
hdmi_drive=2
 +
hdmi_group=2
 +
hdmi_mode=36 #1280x1024 - change to desired resolution
 +
hdmi_force_hotplug=1
 +
</pre>
 +
Turn on the RaspberryPi with the adapter plugged into the HDMI port and the microUSB cord plugged into the adapter. Having the microUSB cord plugged in is critical for it to work. With the Pi still on, unplug the adapter from the HDMI port and remove the VGA cable from the adapter. Now unplug usb cord from the adapter and immediately plug back in. Only the microUSB power cord should be plugged in. Now plug the VGA cord back into the adapter. Both the power cord and the VGA cord should be plugged into the adapter. Plug the adapter back into the HDMI port. Now it should be working. From playing around with the device on my laptop I found that the adapter needs power to be able to tell what the resolution of the VGA monitor is. If it is unable to find the VGA resolution it will not work. Unplugging the HDMI, VGA, and power cord seems to reset the device. Plugging the microUSB cable in seems to turn on the device, allowing VGA resolution detection to work. This method will probably work by just starting the Pi with no adapter plugged in, then just plug in the microUSB, VGA, and HDMI cable in that order.
  
Here It is another option: http://www.dealextreme.com/p/hdmi-v1-4-male-to-vga-female-converter-adapter-cable-white-15cm-130458, is cheap (it's free shipping from china) and works perfectly, I tested it with an Acer VGA monitor (AL1511), without no change in my XBMC distribution.
+
'''HDMI V1.4 Male to VGA Female Converter Adapter'''
 +
* http://www.dealextreme.com/p/hdmi-v1-4-male-to-vga-female-converter-adapter-cable-white-15cm-130458, is cheap (it's free shipping from china) and works perfectly, I tested it with an Acer VGA monitor (AL1511), without no change in my XBMC distribution.
 
The config.txt for Raspbian (Flatron VGA monitor 1024 * 768):
 
The config.txt for Raspbian (Flatron VGA monitor 1024 * 768):
<br>hdmi_drive=2
+
<pre>hdmi_drive=2
<br>hdmi_group=2
+
hdmi_group=2
<br>hdmi_mode=16
+
hdmi_mode=16
<br>hdmi_force_hotplug=1
+
hdmi_force_hotplug=1
<br>disable_overscan=0
+
disable_overscan=0
 +
</pre>
  
 +
''' HDMI - VGA [lontium chip]'''
 +
* http://cgi.ebay.pl/ws/eBayISAPI.dll?ViewItem&item=251086464644. It is very cheap, but it works perfectly. No config.txt changes was needed at all. I've booted Raspbian and OpenELEC. Monitor is detected correctly and the optimal resolution is set (Raspbian) or you can change the res in the menu (OpenELEC).  The /opt/vc/bin/tvservice is able to read monitor edid data. I tested the adapter using NEC 72VM 15" LCD. (1280x1024 60&nbsp;Hz, 1024x768 60&nbsp;Hz, 640x480 works) The adapter is based on Lontium LT8511A chip, but I was unable to get the specification for it. The D1 diode is getting very hot though. Most likely the adapter drives more than 200&nbsp;mA. The standard RS Components 1.2&nbsp;A USB power supply is able to provide enough power for the Raspberry Pi and the adapter. I'll try to modify the adapter to connect external power to bypass D1.
  
And another one: http://cgi.ebay.pl/ws/eBayISAPI.dll?ViewItem&item=251086464644. It is very cheap, but it works perfectly. No config.txt changes was needed at all. I've booted Raspbian and OpenELEC. Monitor is detected correctly and the optimal resolution is set (Raspbian) or you can change the res in the menu (OpenELEC).
+
'''Pi-View HDMI-VGA converter'''
The /opt/vc/bin/tvservice is able to read monitor edid data. I tested the adapter using NEC 72VM 15" LCD. (1280x1024 60&nbsp;Hz, 1024x768 60&nbsp;Hz, 640x480 works) The adapter is based on Lontium LT8511A chip, but I was unable to get the specification for it.
+
* The "Pi-View"  was designed specifically for use with the Raspberry Pi. It does work although the small box gets warm and the video output isn't great (slightly fuzzy text, smaller screen area even with overscan enabled) [http://canada.newark.com/element14/piview/cable-assembly-hdmi-to-vga-adapter/dp/07W8937]
The D1 diode is getting very hot though. Most likely the adapter drives more than 200&nbsp;mA. The standard RS Components 1.2&nbsp;A USB power supply is able to provide enough power for the Raspberry Pi and the adapter. I'll try to modify the adapter to connect external power to bypass D1.
 
Marcin.
 
  
 
===DVI-D -> VGA active adapters===
 
===DVI-D -> VGA active adapters===
Line 2,278: Line 794:
  
 
===Composite->VGA converter boxes===
 
===Composite->VGA converter boxes===
* [http://www.extron.com/product/product.aspx?id=dvs204| Extron DVS-204] - works no problem!
+
* [http://www.extron.com/product/product.aspx?id=dvs204 Extron DVS-204] - works no problem!
 +
 
 +
== Boblight hardware ==
 +
'''Lightberry'''
 +
* http://lightberry.eu it's the first (I think), dedicated hardware for Raspberry Pi that can produce colorful effects behind your TV, when you watch movies or even pictures. It uses GPIO pins (not USB). It is easy to configure - you can even download configured system image from the producer website. Works perfectly :)
  
 
== SD cards ==
 
== SD cards ==
  
The SD card is a key part of the Raspberry Pi; it provides the initial storage for the Operating System and files. Storage can be extended through many types of USB connected peripherals.
+
The SD card section has been moved to a separate page. See [[RPi SD cards]]
 
 
When the Raspberry Pi is 'switched on', i.e. connected to a power supply, a special piece of code called the bootloader is executed, which reads more special code from the SD card that is used to start up the Raspberry Pi. If there is no SD card inserted, it will not start. Do NOT push in or pull out an SD card while the Raspberry Pi is connected to the power, as this is likely to corrupt the SD card data (you might get away with it, but it is best not to).
 
 
 
The SD card must be formatted, or written to, in a special way that means the Raspberry Pi can read the data it needs to start properly. If you are new to this check the instructions, or buy a pre-formatted SD card.
 
 
 
One advantage to using an SD card like this is that you can have several SD cards, each with a different operating system, or a different purpose. Simply power off, switch cards, and reconnect the power. You have a different computer to play with.
 
 
 
=== Which SD card? ===
 
 
 
[[File:SD_Card_dimensions.png‎|right|frameless|SD card sizes]]
 
 
 
SD cards come in three physical sizes (see picture). The Raspberry Pi needs the largest one. The miniSD card and the MicrSD card can be used in a Raspberry Pi, but you will need an adapter / holder to fit it.
 
 
 
SD cards come in a range of storage sizes. You need one of type SDHC, but there are other types of SDSC, SDXC and SDIO which will not work in a Raspberry Pi (confirmation needed). The SDHC type comes in memory sizes of up to 32&nbsp;GB.
 
 
 
There are other properties of SD cards that are not covered here. Read the [http://en.wikipedia.org/wiki/Secure_Digital Wikipedia article] for those details.
 
 
 
=== Other SD card content ===
 
 
 
See the following links for other information:
 
 
 
* [[RPi_Distributions | Select a Distribution]]
 
 
 
* [[RPi_Easy_SD_Card_Setup | Easy SD card set up]]
 
 
 
* [[RPi_Advanced_Setup | Advanced set up]]
 
 
 
* [[R-Pi_Troubleshooting#SD_cards | Troubleshooting]]
 
 
 
* [[RPi_Performance#SD_card | SD card Performance]]
 
 
 
=== Technical Information ===
 
 
 
Note that manufacturers change their designs over time, even as the specs stay the same. (E.g. an ACME 8&nbsp;GB class 4 card manufactured in 2011 might work, while one manufactured in 2012 might not.)
 
For this reason, please specify product numbers in the lists below, when possible.
 
 
 
You can also attach the following fields from your card's CID:
 
<pre>
 
cd /sys/class/mmc_host/mmc?/mmc?:*
 
echo "man:$(cat manfid) oem:$(cat oemid) name:$(cat name) hwrev:$(cat hwrev) fwrev:$(cat fwrev)"
 
</pre>
 
 
 
please merge with http://elinux.org/RPi_Performance#SD_card
 
 
 
===Preinstalled SD cards===
 
A wide range of branded SD cards preinstalled with operating systems are available from [http://thepihut.com The Pi Hut's Raspberry Pi Store].
 
* Raspbian
 
** '''SanDisk'''
 
*** [http://thepihut.com/products/4gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 4GB SDHC Class 4 - preinstalled with Raspbian Wheezy Linux.]
 
*** [http://thepihut.com/products/8gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 8GB SDHC Class 4 - preinstalled with Raspbian Wheezy Linux.]
 
*** [http://thepihut.com/products/16gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 16GB SDHC Class 4 - preinstalled with Raspbian Wheezy Linux.]
 
*** [http://thepihut.com/products/32gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 32GB SDHC Class 4 - preinstalled with Raspbian Wheezy Linux.]
 
** '''Samsung (Class 10)'''
 
*** [http://thepihut.com/products/16gb-samsung-class-10-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 16GB SDHC Class 10 - preinstalled with Raspbian Wheezy Linux.]
 
*** [http://thepihut.com/products/32gb-samsung-class-10-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled 32GB SDHC Class 10 - preinstalled with Raspbian Wheezy Linux.]
 
* XBMC
 
** '''SanDisk'''
 
*** [http://thepihut.com/products/4gb-sandisk-sd-sdhc-card-with-xbmc-preinstalled 4GB SDHC Class 4 - preinstalled with OpenElec XBMC.]
 
*** [http://thepihut.com/products/8gb-sandisk-sd-sdhc-card-with-xbmc-preinstalled 8GB SDHC Class 4 - preinstalled with OpenElec XBMC.]
 
*** [http://thepihut.com/products/16gb-sandisk-sd-sdhc-card-with-xbmc-preinstalled 16GB SDHC Class 4 - preinstalled with OpenElec XBMC.]
 
*** [http://thepihut.com/products/32gb-sandisk-sd-sdhc-card-with-xbmc-preinstalled 32GB SDHC Class 4 - preinstalled with OpenElec XBMC.]
 
 
 
Kingston and other verified SD cards preinstalled with the latest Raspbian operating system are available from many other websites [http://www.amazon.co.uk Amazon UK] and [http://www.ebay.co.uk/ eBay UK].
 
 
 
===Working SD cards===
 
 
 
* '''7DAYSHOP.COM'''
 
** 8&nbsp;GB Professional SDHC Class 10 (man:0x000027 oem:0x5048 name:SD08G hwrev:0x3 fwrev:0x0)
 
 
 
* '''Adata'''
 
** 2&nbsp;GB SD Class 2 Speedy (8B0947 printed on back) This card works with every distro I tried. May be old, may not be the fastest, but it is very stable.
 
** 4&nbsp;GB SDHC Class 4 (BH1109416141G)
 
** 8&nbsp;GB SDHC Class 2 (MMB3F08GWMCA-GE)
 
** 8&nbsp;GB SDHC Class 4 (MicroSD with adapter)
 
** 8&nbsp;GB SDHC Class 6 (MMAGR08GUDCA-DB)
 
** 8&nbsp;GB SDHC Class 10 (AUSDH8GCL10-R)
 
** 8&nbsp;GB SDHC Class 10 (ASDH8GCL10-R) Tested on 2012-06-18-wheezy-beta.zip
 
** 8&nbsp;GB SDHC Class 10 (P-SDH8G10-EC from BJ's USA tested on Raspbian)
 
** 16&nbsp;GB SDHC Class 6
 
** 16&nbsp;GB SDHC Class 10 (16GSDHC10)
 
** 16&nbsp;GB SDHC Class 10 (microSD with adapter AUSDH16GCL10-RA1)
 
** 32&nbsp;GB SDHC Class 10 (ASDH32GCL10-R) Tested on Wheezy-beta with latest kernel and firmware and Raspbian Wheezy
 
 
 
* '''AmazonBasics'''
 
** [http://www.amazon.com/AmazonBasics-SDHC-Class-Secure-Digital/dp/B0058GH0LS 8&nbsp;GB SDHC Class 10 B0058GH0LS]
 
** [http://www.amazon.com/AmazonBasics-SDHC-Class-Secure-Digital/dp/B0058GH1IK 16&nbsp;GB SDHC Class 10 B0058GH1IK]
 
** 32&nbsp;GB SDHC Class 10
 
 
 
* '''Apacer'''
 
** 8&nbsp;GB microSDHC Class 10 (with adapter)
 
** 8&nbsp;GB SDHC Class 6
 
 
 
* '''Centon'''
 
** 16&nbsp;GB SDHC Class 4 (1447 printed on back)
 
 
 
* '''CnMemory'''
 
** 8&nbsp;GB SDHC Class 4 (Silver/Black label says 'High Capacity Card') 84209_8GB_SDHC, bought from Maplins.  No error messages seen, but operation is much slower than with a SanDisk 4&nbsp;GB Class 4 card.
 
 
 
* '''Dane-Elec'''
 
** 16&nbsp;GB SDHC Class 4
 
** 16&nbsp;GB Pro 200X Class 10 DEMS16GB2683ENBA
 
 
 
* '''Dikom'''
 
** 16&nbsp;GB SDHC Class 10 (serial 207H3MD016IBSD)
 
 
 
* '''Duracell'''
 
** 4&nbsp;GB SDHC Class 4
 
** 16&nbsp;GB SDHC Class 10 (labelled Pro Photo 200x)
 
** 32&nbsp;GB SDHC Class 10 (man:0x00001d oem:0x4144 name:SD    hwrev:0x1 fwrev:0x0) (~4.6&nbsp;MB/s read, ~4.4&nbsp;MB/s write on debian6-19-04-2012, following [[RPi_Performance#SD_card]])
 
 
 
* '''Emtec'''
 
** 2&nbsp;GB SD man:0x000027 oem:0x5048 name:SD02G hwrev:0x2 fwrev:0x0
 
** 4&nbsp;GB SDHC Class 4 (EKMSD4G60XHCN)
 
** 16&nbsp;GB SDHC Class 10 (EKMSD16G150XHC) (less than half as fast as SanDisk 16&nbsp;GB Class 10)
 
 
 
* '''Extrememory'''
 
** 16&nbsp;GB SDHC Class 10 (man:0x000012 oem:0x3456 name:F0F0F hwrev:0x1 fwrev:0x0)
 
** 32&nbsp;GB SDHC Class 10 (man:0x000003 oem:0x5344 name:SMI  hwrev:0x1 fwrev:0x0)
 
 
 
* '''Eye-Fi'''
 
** 4&nbsp;GB Wi-Fi SDHC (Wi-Fi doesn't work)
 
 
 
* '''Fugi'''
 
** 32&nbsp;GB SDHC Class 10 (P10NM00580A) (man:0x000073 oem:0x4247 name:NCard hwrev:0x1 fwrev:0x0)
 
 
 
* '''Hama'''
 
** 2&nbsp;GB SD Class 2
 
** 8&nbsp;GB SDHC High Speed Pro Class 6
 
 
 
* '''Hema (Dutch dept. store)'''
 
** 4&nbsp;GB
 
** 8&nbsp;GB SDHC Class 4
 
 
 
* '''Goodram'''
 
** 8&nbsp;GB microSDHC Class 4
 
** 16&nbsp;GB microSDHC Class 4 (SDU16GHCAGRR10)
 
** 16&nbsp;GB SDHC Class 10
 
 
 
* '''HP'''
 
** 8&nbsp;GB SDHC Class 4 (doesn't reboot during first time startup process, but restart again and fine after that).
 
** [http://www.amazon.com/HP-CG790A-AZ-Flash-Memory-Class/dp/B007X7U224 32&nbsp;GB SDHC Class 10]
 
 
 
* '''ICIDU'''
 
** 4&nbsp;GB SDHC Class 10 (also had no issues)
 
** 16&nbsp;GB SDHC Class 10 (image write had issues, might be my inexperience. It boots & shows Xserver)
 
** 32&nbsp;GB SDHC Class 10 (had no issues whatsoever, the comment above might be a dud.)
 
** 8&nbsp;GB microSDHC Class 10
 
** 16&nbsp;GB microSDHC Class 10 (20&nbsp;MB/sec)
 
** 32&nbsp;GB microSDHC Class 10 (20&nbsp;MB/sec)
 
 
 
* '''Integral'''
 
** 4&nbsp;GB SDHC Ultima Pro Class 10
 
** 4&nbsp;GB SDHC Class 4 SD-K04G (Purple label). Also type SD-MO4G.
 
** 8&nbsp;GB SDHC Ultima Pro Class 6 (Works - initial error -110, but it boots within 5 seconds with no further errors or issues)
 
** 8&nbsp;GB SDHC Ultima Pro Class 10 (20&nbsp;MB/s) (Works - initial error -110, but it boots within 5 seconds with no further errors or issues)
 
** 16&nbsp;GB SDHC Ultima Pro Class 6
 
** [http://www.amazon.co.uk/gp/product/B0047T6XME 16&nbsp;GB SDHC Class 10 Ultima Pro (20&nbsp;MB/s)]
 
** 32&nbsp;GB SDHC Ultima Pro Class 10 (20&nbsp;MB/s) - Slow to initially boot past the Rainbow Screen.
 
 
 
* '''Joyflash'''
 
** 16&nbsp;GB SDHC Class 10 (LTSD1112016GB)
 
 
 
* '''Kingmax'''
 
** 4&nbsp;GB SDHC Class 2
 
** 4&nbsp;GB microSDHC Class 4 (KM04GMCSDHC4) won`t reboot when it`s hot
 
** 8&nbsp;GB microSDHC Class 4 (KM08GMCSDHC41A) won`t reboot when it`s hot
 
 
 
* '''Kingston'''
 
** 2&nbsp;GB SD
 
** 2&nbsp;GB microSD (N0185-002.A00LF) + Adapter (File system .img written via Transcend microSDHC "USB stick-like" adapter - P3-102510)
 
** 4&nbsp;GB microSD Class 4
 
** 4&nbsp;GB SDHC Class 4 (SD4/4&nbsp;GB) (Writes at 4.8&nbsp;MB/s, Reads at 9&nbsp;MB/s)
 
** 4&nbsp;GB SDHC Class 10 (SD10V/4&nbsp;GB)
 
** [http://img341.imageshack.us/img341/1619/dsc0253y.jpg 8&nbsp;GB SDHC Class 4] ([http://img833.imageshack.us/img833/2028/dsc0254br.jpg SD4/8&nbsp;GB]) (Works reliably with Raspbian 28-10-2012 and previous Debian releases) (Writes at 4.8&nbsp;MB/s, Reads at 9&nbsp;MB/s)
 
** [http://img600.imageshack.us/img600/3849/dsc0251et.jpg 8&nbsp;GB microSDHC Class 4] ([http://img707.imageshack.us/img707/363/dsc0252ld.jpg SDC4/8&nbsp;GB])
 
** 8&nbsp;GB SDHC Class 6 (SD6/8&nbsp;GB) (errors on boot, boots Debian OK)
 
** 8&nbsp;GB SDHC Class 10 (SD10G2/8&nbsp;GB, SD10V/8&nbsp;GB, ultimateX 100X, ultimateX 120X)
 
** 16&nbsp;GB SDHC Class 4 (SD4/16&nbsp;GB)
 
** 16&nbsp;GB microSDHC Class 10 (SDC10/16&nbsp;GB)
 
** 16&nbsp;GB SDHC Class 10 (SD10G2/16&nbsp;GB, ultimateX 100X)
 
** 16&nbsp;GB SDHC Class 10 (SD4/16GBET)
 
** 32&nbsp;GB SDHC Class 10 (SD10V)
 
** 32&nbsp;GB SDHC Class 10 (SD10G2/32&nbsp;GB, ultimateX 100X)
 
** 64&nbsp;GB SDXC Class 10 (SDX10V/64&nbsp;GB)
 
 
 
* '''Kodak'''
 
** 4&nbsp;GB SDHC Class 2
 
** 8&nbsp;GB SDHC Class 4
 
 
 
* '''Kruidvat'''
 
** 8&nbsp;GB SDHC Class 4
 
** 8&nbsp;GB SDHC Class 10 (actually cheaper then the class 4 in my store)
 
 
 
* '''Lexar'''
 
** 4&nbsp;GB SDHC Class 4 (Boots consistently and no error messages in log after 1/2 hour use ) (works with Raspbmc)
 
** 4&nbsp;GB SDHC Class 6 Platinum II (from [http://www.microcenter.com/single_product_results.phtml?product_id=0350735 Microcenter])
 
** 8&nbsp;GB SDHC Class 4
 
** 8&nbsp;GB SDHC Class 6 Premium Series
 
** 8&nbsp;GB SDHC Class 6 Platinum II
 
** 16&nbsp;GB SDHC Class 6 Platinum II
 
** 32&nbsp;GB microSDHC HIGH-SPEED Class 10 (from [http://www.amazon.co.uk/Lexar-32GB-Micro-Speed-Reader/dp/B004BR2ZTM Amazon])
 
** 128&nbsp;GB SDXC UHS-I Card LSD128CTBNA400 (from [http://www.amazon.com/gp/product/B007BZRXK2 Amazon])
 
 
 
* '''Master'''
 
** 16&nbsp;GB SDHC Class 10 [man:0x000003 oem:0x5344 name:SMI  hwrev:0x1 fwrev:0x0]
 
 
 
* '''Medion'''
 
** 8&nbsp;GB Class 4 SDHC UK sourced (Aldi)
 
* '''Microcenter Brand (sold in bins at checkout)'''
 
** [http://www.microcenter.com/single_product_results.phtml?product_id=0289508 8&nbsp;GB SDHC Class 4]
 
** [http://www.microcenter.com/single_product_results.phtml?product_id=0349728 8&nbsp;GB SDHC Class 10]
 
** [http://www.microcenter.com/single_product_results.phtml?product_id=0349729 16&nbsp;GB SDHC Class 10]
 
 
 
* '''Mushkin'''
 
** 16&nbsp;GB SDHC Class 10 (MKNSDHCU1-16GB) [http://www.newegg.com/Product/Product.aspx?Item=N82E16820226324]
 
** 32&nbsp;GB SDHC Class 10 (MKNSDHCC10-32GB) [http://www.newegg.com/Product/Product.aspx?Item=N82E16820226235]
 
 
 
* '''Mustang'''
 
** [http://www.mustang-flash.de/Products/Flash%20Products/Secure%20Digital/SD-Card/8GB%20Mustang%20SDHC%20Card%20LeMans%2C%20Class%2010%2C%20Retail|SD8GHCCL10MU-R.html 8&nbsp;GB SDHC Class 10]
 
 
 
* '''MyMemory'''
 
** 8&nbsp;GB SDHC Class 10 (MYMESDH8G10) [http://www.mymemory.co.uk/SDHC/MyMemory/MyMemory-8GB-SD-Card-%28SDHC%29---Class-10 MyMemory 8&nbsp;GB class 10] (Latest batch not working)
 
** 16&nbsp;GB SDHC Class 10 (MYMESDH16G10) [http://www.mymemory.co.uk/SDHC/MyMemory/MyMemory-16GB-SD-Card-(SDHC)---Class-10]
 
** 32&nbsp;GB SDHC Class 10 [http://www.mymemory.co.uk/SDHC/MyMemory/MyMemory-32GB-SD-Card-%28SDHC%29---Class-10]
 
 
 
* '''NovaTech'''
 
** 8&nbsp;GB SDHC Class 10 (Integral Branded)
 
 
 
* '''OCZ'''
 
** 8&nbsp;GB SDHC Class 6 Gold Series (08110596-8GB-6) tested with Debian Squeeze (official Raspberry Pi distribution debian6-19-04-2012.zip)
 
 
 
* '''Optima'''
 
** 8&nbsp;GB SDHC Class 10 (Pro-Speed)
 
** 8&nbsp;GB SDHC Class 4 - working from 2012-09-18
 
 
 
* '''Panasonic'''
 
** 4&nbsp;GB SDHC Class 4
 
** 4&nbsp;GB SDHC Class 10 UHS-I  (~11.2&nbsp;MB/s read, ~6.2&nbsp;MB/s write, following [[RPi_Performance#SD_card]])
 
** 8&nbsp;GB SDHC Class 2 (~11.1&nbsp;MB/s read, ~9.7&nbsp;MB/s write, following [[RPi_Performance#SD_card]])
 
** 8&nbsp;GB SDHC Class 6 (~4.8&nbsp;MB/s read, ~4.4&nbsp;MB/s write, following [[RPi_Performance#SD_card]])
 
 
 
* '''Patriot'''
 
** 8&nbsp;GB SDHC Class 6 (PSF8GSDHC10-PC)
 
** 8&nbsp;GB SDHC Class 10 LX Series (PSF8GSDHC10-PC1)
 
** 16&nbsp;GB SDHC Class 10 (PSF16GMCSDHC10)
 
** 16&nbsp;GB SDHC Class 10 LX Series (PSF16GSDHC10) (19.3&nbsp;MB/s read, 9.3&nbsp;MB/s write)
 
** 16&nbsp;GB microSDHC Class 10 (PSF16GMSHC10) (requires recent kernel update for boot)
 
** 32&nbsp;GB SDHC Class 10 (PSF32GSDHC10)
 
** 32&nbsp;GB SDHC Class 10 UHS-1 (PEF32GSDHC10U1) (20.4&nbsp;MB/s read, 12.1&nbsp;MB/s  write)
 
 
 
* '''Peak'''
 
** 4&nbsp;GB microSDHC Class 4 (MMBTR04GUBCA-ME) tested with Arch
 
 
 
* '''Philips'''
 
** 8&nbsp;GB SDHC Class 4 (FM08SD35B)
 
 
 
* '''Platinum'''
 
** 4&nbsp;GB SDHC Class 6
 
** 8&nbsp;GB SDHC Class 6 (man:0x00006f oem:0x0000 name:SMI  hwrev:0x1 fwrev:0x0)
 
** 64&nbsp;GB SDCX Class 10
 
 
 
* '''Play.com'''
 
** 4&nbsp;GB SDHC Class 6 (S4E3CD04GEFAA 0907090121106)
 
 
 
* '''PNY'''
 
** 4&nbsp;GB SDHC Class 4
 
** 4&nbsp;GB SDHC Class 4 Optima (SD-K04G 0834TT1297Y)
 
** 4&nbsp;GB SDHC Class 4. Micro SD card with adapter.
 
** 8&nbsp;GB SDHC Class 6
 
** 8&nbsp;GB SDHC Class 10. Micro SD card with adapter.
 
** 16&nbsp;GB SDHC Class 4
 
** 16&nbsp;GB SDHC Class 10 (P-SDHC16G10-GE)
 
*** See the note for P-SDHC16G10-EF. Works with Wheezy, does not work with Squeeze, Arch, or Fedora Remix.
 
** 16&nbsp;GB SDHC Class 10 (P-SDHC16G10-EF)
 
*** Works with [http://www.raspberrypi.org/archives/1435 Debian Wheezy]
 
*** Does not work with Debian Squeeze (debian6-19-04-2012: mmc0: timeout waiting for hardware interrupt).
 
*** Does not work with Arch Linux Arm (archlinuxarm-29-04-2012: no video is displayed, solid red power light, tiny green light)
 
** 16&nbsp;GB SDHC Class 10 Pro-Elite (P-SDH16U1-30-GE). Works with Raspbmc, haven't tested others.
 
 
 
* '''pqi'''
 
** 8&nbsp;GB SDHC Class 6
 
*** Works with official debian6-19-04-2012
 
 
 
* '''PRETEC'''
 
** 8&nbsp;GB SDHC Class 10 (8DK52-122ME)
 
 
 
* '''Samsung'''
 
** 4&nbsp;GB SDHC
 
** 8&nbsp;GB SDHC Class 6 (MB-SS8GAEU)
 
** 8&nbsp;GB SDHC Class 10 (MB-MP8GA, MB-SP8GA/EU, MB-SP8GA/AM)
 
** 16&nbsp;GB SDHC Class 6 (MB-SSAGAEU)
 
** 16&nbsp;GB SDHC Class 10 (MB-SPAGA AKA MB-SPAGAEU)
 
** 32&nbsp;GB SDHC Class 10 (MB-SSBGA, MBSSBGVEOBGA-SH) fine with [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=50&t=8071 Debian Wheezy], but it does not work with Debian Squeeze (debian6-19-04-2012: mmc0: timeout waiting for hardware interrupt).
 
 
 
* '''SanDisk'''
 
** 2&nbsp;GB SD, white "SanDisk for Wii" branded, no class mentioned
 
** 2&nbsp;GB SD (with a circle 2 --probably class 2), writes at 3.5&nbsp;MB/s
 
** 2&nbsp;GB SD Class 2 (BE0816113150D)
 
** 2&nbsp;GB SD Class 4 Ultra (15&nbsp;MB/s)
 
** 2&nbsp;GB SD Class 4 Ultra II
 
** 2&nbsp;GB SD Ultra II (BE0719111366D)
 
** 2&nbsp;GB SD Extreme III (BE0715105083B)
 
** 2&nbsp;GB SD Extreme III (BE0804212046D) - 20&nbsp;MB/s  - Class 6
 
** 4&nbsp;GB SDHC Class 2 (BH0820113475D) - Tested with RPITC (Based on Raspbian Wheezy)
 
** 4&nbsp;GB SDHC Class 4 (SDSDB-004G-B35)
 
** 4&nbsp;GB SDHC Class 4 (SDSDB-004G-BT35). Confirmed working with stock debian6-19-04-2012.img
 
** 4&nbsp;GB SDHC Class 4 (BH1210821913G)
 
** 4&nbsp;GB SDHC Class 4 (SDSDH2-004G-AC11, BH1127216239D) Costco 2-pack, booting Wheezy 2012-07-15
 
** 4&nbsp;GB SDHC Class 4 Ultra (SDSDH-004G-U46) won`t reboot when it`s hot
 
** 4&nbsp;GB SDHC Class 4 Ultra II
 
** 4&nbsp;GB SDHC Class 6 Extreme III labelled as 30&nbsp;MB/s works with (B) 2012-10-28-Wheezy-raspbian
 
** 4&nbsp;GB SDHC Class 6 Ultra 30&nbsp;MB/s BH1200421822D)
 
** 4&nbsp;GB SDHC Class 6 Ultra (SDSDH-004G-U46 - BH1136121837G, BH1130521822D)
 
** 4&nbsp;GB SDHC Class 10 Extreme (BH10297143382G)
 
** 8&nbsp;GB SDHC Class 4 (writes at ~1.5&nbsp;MB/s)
 
** 8&nbsp;GB SDHC Class 4 Ultra labelled as 15&nbsp;MB/s (BI1024716014G)
 
** 8&nbsp;GB SDHC Class 6 Ultra
 
** 8&nbsp;GB SDHC Class 6 micro - MMAGR08GUDCA-DB
 
*** also SDSDH-008G-U46 - BI1131222083D see [http://www.raspberrypi.org/phpBB3/viewtopic.php?p=88625#p88625 update from andrew.blake]
 
*** except SDSRH-008G-A11 could be problematic, see below
 
** 8&nbsp;GB SDHC Class 6 Ultra labelled as 20&nbsp;MB/s (BI11321422083D)
 
** 8&nbsp;GB SDHC-I Class 6 Ultra labelled as 30&nbsp;MB/s (SDSDH2-008G-AC11)
 
*** requires updated Squeeze or Wheezy beta
 
** 8&nbsp;GB SDHC Class 10 Extreme (BI11017514367G)
 
** 8&nbsp;GB SDHC Class 10 Extreme (B11209116254G) - Managed to get it working with Raspbian R3 [http://archive.raspbian.org/images/rpi_pisces_r3.zip rpi_pisces_r3.zip] however does not work with official Squeeze nor Arch linux.
 
** 8&nbsp;GB SDHC Class 10 Extreme (30&nbsp;MB/s HD Video) - working with new [https://github.com/raspberrypi/firmware/blob/9308c7ed387e5422883753f7fb71a75506abd1f8/boot/bootcode.bin bootcode.bin]. Confirmed on 2012-07-10 for Debian Squeeze 2012-04-19 and Arch Linux 2012-06-13 images (BI1130916254G).
 
** 8&nbsp;GB SDHC Class 10 Ultra(30&nbsp;MB/s) (SDSDU-008G-U46) - Works with stock debian6-19-04-2012 or Raspbian images but not with OpenELEC r11212 (works with OpenELEC r11493)
 
** 8&nbsp;GB SDHC Class 10 Ultra(30&nbsp;MB/s) (SDSDU-008G-UDQ46) - Works with stock 2012-09-18-Wheezy-Raspbian
 
** 8&nbsp;GB SDHC Class 10 Extreme (SDSDX-008G-X46/BI1218822414G) - Works with stock 2012-08-16-Wheezy-Raspbian
 
** 8&nbsp;GB SDHC Class 10 Extreme Pro (95&nbsp;MB/s UHS-I) (SDSDXPA-008G-X46) - Works with stock 2012-07-15-Wheezy-Raspbian
 
** 16&nbsp;GB SDHC Class 4
 
** 16&nbsp;GB SDGC Class 4 (SDSDB-016G-B35) - working with [https://github.com/raspberrypi/firmware/blob/234c19de7cbaaf4997671d61df20a05759066295/boot/bootcode.bin bootcode.bin]. Confirmed on 2012-07-15 for Debian Squeeze 2012-04-19
 
** 16&nbsp;GB SDHC Class 6 Ultra (30&nbsp;MB/s) (BL1133921933G) - Work with OpenELEC r11324
 
** 16&nbsp;GB SDHC Class 10 Ultra(30&nbsp;MB/s) (SDSDU-016G-U46) - Work with stock debian6-19-04-2012 image. Gave Kernel Panic with stock debian6-19-04-2012 image. Worked fine with Wheezy image.
 
** 16&nbsp;GB SDHC Class 10 Extreme (30&nbsp;MB/s HD Video) (SDSDX3-016G-X46) - Works with 2012-06-18-wheezy-beta.img and updated firmware (tested 2012-07-02)
 
** 16&nbsp;GB SDHC Class 10 Extreme (45&nbsp;MB/s U1) (BL1203322025G) - Works with 2012-08-16-wheezy-raspbian.img (tested 2012-09-15). Doesn't work with stock debian6-19-04-2012 image, but it does work with a freshly compiled kernel.
 
** 16&nbsp;GB SDHC Class 10 Extreme (45&nbsp;MB/s) (SDSDX-016G-X46) (UPC 619659062224) - Works with 2012-09-18-wheezy-raspbian.img (tested 17/10/2012). <ins datetime="2012-11-22T22:08+11:00">Working with Raspbmc RC5 if writing standalone image; working with Raspbian “Wheezy”.</ins>
 
** 16&nbsp;GB SDHC Class 10 Extreme (45&nbsp;MB/s) (SDSDXPA-016G-FPP) - Working with latest RaspBMC image (tested 12/09/2012) [http://www.amazon.co.uk/gp/product/B00422J0CG/ref=oh_details_o00_s00_i00 Amazon Link]
 
** 16&nbsp;GB SDHC Class 10 Extreme Pro (95&nbsp;MB/s UHS-I) (SDSDXPA-016G-A75) - Doesn't work with stock debian6-19-04-2012 image, but it does work with a freshly compiled kernel.
 
** 32&nbsp;GB SDHC Class 4
 
** 32&nbsp;GB SDHC Class 6
 
** 32&nbsp;GB SDHC Class 10 Ultra (30&nbsp;MB/s) - Works with stock debian6-19-04-2012 image
 
** 32&nbsp;GB SDHC Class 10 Extreme (45&nbsp;MB/s UHS-I) (SDSDX-032G-X46) - works with arch-04-29-image and latest firmware (booting problems without firmware update)
 
** 64&nbsp;GB SDXC Class 10 Extreme (45&nbsp;MB/s UHS-I) (SDSDX-064G-X46) - works with 2012-07-15-Wheezy-Raspbian
 
** microSDHC / microSDXC
 
*** 4&nbsp;GB microSDHC Class 2
 
*** 4&nbsp;GB microSDHC Class 4
 
*** 8&nbsp;GB microSDHC Class 2
 
*** 8&nbsp;GB microSDHC Class 4
 
*** 8&nbsp;GB microSDHC Class 6 Mobile Ultra (SDSDQY-008G-U46A) working with the latest firmware, won`t reboot when it`s hot
 
*** 8&nbsp;GB microSDHC Class 10 Ultra(30&nbsp;MB/s) (SDSDQU-008G-U46) tested and working on Raspbian Wheezy (and RaspBMC)
 
*** 16&nbsp;GB microSDHC Class 10 Mobile Ultra (SDSDQUA-016G-U46A) working with the latest firmware
 
*** 32&nbsp;GB microSDHC Class 4 (SDSDQM-032G-B35)
 
*** [http://img217.imageshack.us/img217/6435/dsc0255uc.jpg 64&nbsp;GB microSDXC Class 6 Mobile Ultra] (SDSDQY-064G-A11A) (boots up much more consistently with latest firmware)
 
 
 
* '''Silicon Power'''
 
** 4&nbsp;GB microSDHC Class 6 (SP004GBSTH006V10-SP)
 
** 8&nbsp;GB microSDHC Class 10 (S608G1202)
 
** 16&nbsp;GB microSDHC Class 10 (SP016GBSTH010V10)
 
** 16&nbsp;GB SDHC Class 10 (SP016GBSDH010V10)
 
 
 
* '''Sony'''
 
** 4&nbsp;GB SDHC Class 4 (SF-4B4) (Write 6&nbsp;MB/s, Read 20&nbsp;MB/s)
 
** 4&nbsp;GB SDHC Class 4 (SF-4N4)
 
** 8&nbsp;GB SDHC Class 4 (Write 11.8&nbsp;MB/s, Read 17.4&nbsp;MB/s)
 
** [http://store.sony.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10551&storeId=10151&langId=-1&partNumber=SF32NX/TQ#features 32&nbsp;GB SDHC Class 10 (SF-32NX/TQ)] (Max read speed of ~94&nbsp;MB/s, min write speed of ~10&nbsp;MB/s) - Works with archlinuxarm-29-04-2012 dd image with latest firmware update (as of 10-06-2012)
 
 
 
* '''Strontium'''
 
** 8&nbsp;GB SDHC Class 10 (SD-T08G 1045 US6923 G (White Shell - SKU 8 886450 703492))
 
* '''Super Talent'''
 
** 32&nbsp;GB Secure Digital High Capacity SDHC Card (Class 10), Model SDHC32-C10 SKU: 116-557-001 (works with Raspbmc RC4 and 2012-07-15-Wheezy-Raspbian))
 
 
 
* '''TakeMS'''
 
** 4&nbsp;GB microSDHC Class 4 (with adapter) [http://www.takems.com/products.php?categ=flash&prod=Micro_SDHC-Card Micro SDHC Class 4 + 1 Adapter(Order No.88662)]
 
 
 
* '''TDK'''
 
** 4&nbsp;GB SDHC Class 4 (1008WW5261B)
 
** 4&nbsp;GB SDHC Class 4 (80-56-10275-004G,Debian works '''BUT''' mmc0 errors when booting Fedora)
 
** 4&nbsp;GB microSDHC Class 4 (80-56-10301-004G)
 
** 4&nbsp;GB SDHC Class 6 (S404G1113) - Works with Debian Wheezy (2012-06-18 beta), not tried latest OpenELEC yet.
 
** 8&nbsp;GB SDHC Class 10 - Works with Raspbian 2012-07-15
 
** SanDisk 64&nbsp;GB Class 10 Ultra SDXC UHS-I FFP (3A114807)
 
 
 
* '''Toshiba'''
 
** 8&nbsp;GB mircoSDHC SD-C08GJ(BL3A
 
** 16&nbsp;GB SDHC Class 10 SD-T16G (1046 US7022 C)
 
 
 
* '''Transcend'''
 
** 4&nbsp;GB SDHC Class 4 - we've found these to work without any errors and offer reasonable performance
 
** 4&nbsp;GB SDHC Class 4 (TS4GSDHC4 - BH1130821915G)
 
** 4&nbsp;GB SDHC Class 6 (TS4GSDHC6) - no problems. (does not work with Raspbmc as of 6/1/12)
 
** 4&nbsp;GB SDHC Class 10 (TS4GSDHC10E)
 
** [http://www.mymemory.co.uk/SDHC/Transcend/Transcend-8GB-SD-Card-(SDHC)---Class-4 8&nbsp;GB SDHC Class 4] (TS8GSDHC4) (man:0x000003 oem:0x5344 name:SD08G hwrev:0x8 fwrev:0x0) - works with both Debian "squeezy" and Raspbian "Wheezy" distributions.
 
** 8&nbsp;GB SDHC Class 6 (~5.8&nbsp;MB/s read/write following [[RPi_Performance#SD_card]])
 
** 8&nbsp;GB SDHC Class 6 (TS8GSDHC6-P2 - MMBFG08GWACA-M6)
 
** 8&nbsp;GB SDHC Class 10 (TS8GSDHC10) [http://www.mymemory.co.uk/SDHC/Transcend/Transcend-8GB-SD-Card-%28SDHC%29---Class-10- Transcend 8G class 10]
 
** 16&nbsp;GB SDHC Class 6 (TS16GSDHC6)
 
** 16&nbsp;GB SDHC Class 10 (TS16GSDHC10)(TS16GSDHC10E)(man:0x000074 oem:0x4a45 name:SDC  hwrev:0x1 fwrev:0x0)
 
** [http://www.transcend.com.es/tarjetas-de-memoria/sd-sdhc/32gb-sdhc-class-10 32&nbsp;GB SDHC Class 10] (TS32GSDHC10)(TS32GSDHC10E)
 
** 64&nbsp;GB SDXC Class 10 (TS64GSDXC10)
 
 
 
* '''Verbatim'''
 
** 8&nbsp;GB SDHC Class 10 (43961)
 
** 16&nbsp;GB SDHC Class 4 (44020)
 
** 16&nbsp;GB SDHC Class 10 (43962)
 
** 32&nbsp;GB SDHC Class 6 (44032)
 
 
 
*'''Traveler'''
 
**4&nbsp;GB High Speed Memory Card - no class mentioned. No problems. Tested with Raspbian.
 
 
 
* '''The Pi Hut'''
 
** SanDisk 4&nbsp;GB Class 4 - preinstalled with Raspbian Wheezy Linux. (from [http://thepihut.com/products/4gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled The Pi Hut's Raspberry Pi Store])
 
** SanDisk 8&nbsp;GB Class 4 - preinstalled with Raspbian Wheezy Linux. (from [http://thepihut.com/products/8gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled The Pi Hut's Raspberry Pi Store])
 
** SanDisk 16&nbsp;GB Class 4 - preinstalled with Raspbian Wheezy Linux. (from [http://thepihut.com/products/16gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled The Pi Hut's Raspberry Pi Store])
 
** SanDisk 32&nbsp;GB Class 4 - reinstalled with Raspbian Wheezy Linux. (from [http://thepihut.com/products/32gb-sandisk-sd-sdhc-card-with-raspbian-wheezy-linux-preinstalled The Pi Hut's Raspberry Pi Store])
 
 
 
* '''V-Gen'''
 
** 8&nbsp;GB microSDHC - no class mentioned. No problems.(man:0x000073 oem:0x4247 name:NCard hwrev:0x1 fwrev:0x0). Tested with Raspbian Wheezy & Raspbmc.
 
 
 
* '''Veho (http://www.veho-uk.com)'''
 
** 8&nbsp;GB "Ultra Fast" Class 6. (man:0x00001b oem:0x534d name:00000 hwrev:0x1 fwrev:0x0) 7.8&nbsp;MB/s. Slow but tested with Arch Linux.
 
 
 
* '''W Photo (Walgreens photo)'''
 
** 1&nbsp;GB SD memory card. Works with Raspbmc, have not tested others.
 
** 2&nbsp;GB SD memory card. Works with Raspbian, not tested with others.
 
 
 
Known good (and pre-loaded) cards will be available for sale from RS and element14 at a ''later'' date (TBA).
 
 
 
===Problem SD cards===
 
 
 
Make sure that you buy your card from a reliable source. There are many cheap Chinese copies of (brand name) SD-Cards on the market, [http://www.petapixel.com/2011/05/20/one-third-of-the-sandisk-memory-cards-on-earth-are-counterfeit/] in addition they are often mislabeled as having greater capacity than they really have. For example they might be sold as being 4&nbsp;GB, but they are actually 2&nbsp;GB (or even less).
 
 
 
There were initially issues with most Class 10 SDHC cards, apparently due to a bug in the Broadcom bootloader.[http://www.raspberrypi.org/forum/general-discussion/class-10-sd-cards-on-the-production-boards/page-3/#p39181]
 
 
 
This seems to have been fixed in sdhci.c: [https://github.com/raspberrypi/linux/commit/7e8ae226fe6e95954df6b0dcdde40a53dbbc1a0b] Further feedback will be useful.
 
 
 
If you add an SD card here, please also mention the kernel date and the date you tried it. This allows people to estimate how likely it is that a driver-fix in the kernel has been fixed. (i.e. I think some/most of the cards here work fine now, because a problem in the kernel driver has been fixed).
 
 
 
* '''Acumem'''
 
** 8&nbsp;GB SDHC Class 6 (many errors on 6/7/2012)
 
* '''Adata'''
 
** 2&nbsp;GB Speedy (MMAGF02GWMCA -NA)
 
** 8&nbsp;GB SDHC Class 6 - Sometimes boots
 
** 16&nbsp;GB SDHC Class 6 (Possibly SD5MY168G0, label with gold <> black gradient) - Doesn't boot
 
* '''Agfa'''
 
** 16&nbsp;GB MicroSDHC class 6 (as written on SD-Adapter, MicroSD card itself no-name? ENAAJK121960): mixed results, such a card was working on another Raspberry Pi.
 
* '''Amazon Basics'''
 
** 16&nbsp;GB SDHC Class 10 (many errors on 6/7/2012)
 
* '''Delkin Devices'''
 
** 4&nbsp;GB SDHC Class 6 "Delkin pro" -- Note: works with Fedora Beefy Miracle 17
 
* '''GSkill'''
 
** 32&nbsp;GB SDHC Class 10
 
* '''Integral'''
 
** 16&nbsp;GB SDHC Class 6 Ultima Pro (SH016GAA2BB)
 
** 4&nbsp;GB SDHC class 4 (S404G1115)
 
* '''Kingston'''
 
** 2&nbsp;GB SD [http://www.geeks.com/details.asp?invtid=KING-SD-M02G-BULK looks like this] - it boots the kernel, but it damages the filesystem.
 
** 4&nbsp;GB SDHC Class 6 - Boots kernel, but it won't run init (times out)
 
** 8&nbsp;GB/Go SDHC Class 10 - SD10V/8&nbsp;GB Very slow writing images to card and then either won't boot, or boots very slowly
 
** 16&nbsp;GB SDHC Class 4 (SDC4/16&nbsp;GB) - Reported earlier as not working. Stable and works well with all Debian/Raspbian releases
 
** 16&nbsp;GB SDHC Class 10 (SD10V/16&nbsp;GB) - Starts boot OK, but then gets stuck in mmc0 timeouts.
 
* '''Memory2GO'''
 
** 4&nbsp;GB SDHC Class 6 (S404G1029) - I/O Errors leading to Kernel Panic on startup.
 
* '''Micro Center'''
 
**4&nbsp;GB SDHC Class 4 — hasn't worked with any of the images I've tried; appears to be completely unrecognized
 
* '''MyMemory.com'''
 
** 8&nbsp;GB SDHC Class 10
 
 
 
* '''Optima'''
 
** <del>8&nbsp;GB SDHC Class 4 - Does not boot with Raspbian Wheezy 2012-07-15</del> - works with 2012-09-18
 
 
 
* '''Panasonic'''
 
** 8&nbsp;GB SDHC Class 10 (RP-SDU08GD1K) mmc0: timeout waiting for hardware interrupt [http://www.mymemory.co.uk/SDHC/Panasonic/Panasonic-8GB-UHS-1-London-2012-Collection-SDHC-Card---Class-10 Panasonic 8&nbsp;GB Class 10]
 
* '''Patriot'''
 
** 8&nbsp;GB SDHC Class 6 (PS8GSDHC10-BC) - repeatable corruption after 1 or 2 reboots with 2012-07-15-Wheezy-Raspbian
 
** 8&nbsp;GB SDHC Class 10 (PSF8GSDHC10)
 
** 8&nbsp;GB SDHC Class 10 (PSF8GSDHC10-PC) - won't even boot 2012-08-16-Wheezy-Raspbian (mmc0: timeout waiting for hardware interrupt, followed by continuous I/O errors, timeouts, etc.). It seems functional in Arch, but sometimes it freezes at the beginning of boot (blinking underscore).
 
* '''Platinum'''
 
** 8&nbsp;GB SDHC Class 8 (O08G840 M3100487 TW)
 
** 16&nbsp;GB SDHC Class 10 (article code 177117) - Does not boot with Raspbian Wheezy 2012-09-12
 
* '''PNY'''
 
** 8&nbsp;GB Optima SDHC 120 HD Class 4 SD-K08G 0928 WF3673 - mmc -110 errors at init time on 6/12/12
 
** 8&nbsp;GB Premium SDHC Class 4 - mmc -  mmc0: timeout waiting for hardware interrupt
 
** 32&nbsp;GB SDHC Class 10 Professional (P-SDHC32G10-EF) from [http://www.play.com/Electronics/Electronics/4-/18814903/-/Product.html play.com] (mmc0 timeout with Debian, error -84 whilst initialising sd card with Fedora and QtonPi. Arch seems to work, gets to the login prompt)
 
** 2&nbsp;GB card SD-M02G
 
* '''Polaroid'''
 
** 16&nbsp;GB SDHC C10 (P-SDHC16GB10-EFPOL) - mmc0: timeout waiting for hardware interrupt on debian6-19-04-2012
 
* '''PRETEC'''
 
** 8&nbsp;GB SDHC Class 10 233x - mmc0: timeout waiting for hardware interrupt, Sometimes does not boot, kernel panic, ...
 
* '''Reekin'''
 
** 4&nbsp;GB HighSpeed SH4GC6M16MIN9C0812TE (old) don't boot ! (11/07/2012)
 
* '''Samsung'''
 
** 4&nbsp;GB SDHC Class 4 (MB-SS4G MBSS4GMBDDBA-DD) doesn't boot with [http://downloads.raspberrypi.org/images/raspbian/2012-07-15-wheezy-raspbian/2012-07-15-wheezy-raspbian.zip 2012-07-15-wheezy-raspbian] - OK light partially lit.
 
** 32&nbsp;GB SDHC Class 10 (MB-SSBGA, MBSSBGVEOBGA-SH) does not work with Debian Squeeze (debian6-19-04-2012: mmc0: timeout waiting for hardware interrupt), but it works fine with  [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=50&t=8071 Debian Wheezy]
 
* '''SanDisk'''
 
** 2&nbsp;GB SD Extreme III (BE0722702998D) (man:0x000003 oem:0x5344 name:SD02G hwrev:0x8 fwrev:0x0) - tested with Raspbian (build 2012-07-15) and Raspbmc installer (build 2012-07-13)
 
** 2&nbsp;GB SD (BE0916214253D)
 
** 2&nbsp;GB Ultra || 15&nbsp;MB/s (BE0828713280D)
 
** 4&nbsp;GB SDHC Class 2 - Debian and XBMC boot, but Fedora gets a lot of mmc0 note long write sync errors and then hc_xfer_timeout errors at the login prompt.
 
** 4&nbsp;GB SDHC Class 2 "Limited Edition" (8H825413279G) - Error -110 whilst initialising sd card
 
** 4&nbsp;GB SDHC Class 4 (BH1030216016G) - Doesn't boot.
 
** 4&nbsp;GB SDHC Class 4 (BH1031116016G) - Doesn't boot.
 
** 4&nbsp;GB SDHC Class 6 Extreme (BH0822411730D)
 
** 4&nbsp;GB SDHC Class 6 Extreme III (30&nbsp;MB/s) (BH0822712362G)
 
** 4&nbsp;GB SDHC Class 10 Extreme (SDSDX-004G-X46) (30&nbsp;MB/s HD Video) doesn't boot (also not with new kernel.img and start.elf 17-06-2012 or "Wheezy"-beta)
 
** 4&nbsp;GB SDHC Class 10 Extreme (30&nbsp;MB/s HD Video) (Doesn't boot) - Works with new kernel.img and start.elf [https://github.com/raspberrypi/firmware/tree/master/boot]
 
** 4&nbsp;GB microSDHC Class 6 Mobile Ultra (tried 15-06-2012 with kernel 19-04-2012) error -84 transferring data, kernel panic: no init found
 
** 8&nbsp;GB SDHC Class 6 Ultra (B11201421964G)
 
** <del>8&nbsp;GB SDHC Class 6 Ultra (SDSDH-008G-U46 - BI1131222083D) - Boots kernel, but it won't run init (mmc timeout waiting for interrupt)</del> see [http://www.raspberrypi.org/phpBB3/viewtopic.php?p=88625#p88625 update from andrew.blake]
 
** 8&nbsp;GB SDHC Class 6 Ultra labelled as 30&nbsp;MB/s (BI1208721965G)) - Boots kernel, but it won't run init (mmc timeout waiting for interrupt)
 
** 8&nbsp;GB SDHC Class 6 Ultra labelled as 30&nbsp;MB/s SDSRH-008G-A11 - Boots kernel, but it won't run init (mmc timeout waiting for interrupt)
 
** 8&nbsp;GB SDHC Class 6 Ultra labelled as 30&nbsp;MB/s SDSDH-008G-T11 - Boots kernel, but it won't run init (debian6-19-04-2012: mmc timeout waiting for interrupt), but works fine with [http://www.raspberrypi.org/phpBB3/viewtopic.php?f=50&t=8071 Debian Wheezy] on 6/22/12
 
** 8&nbsp;GB SDHC Class 6 Ultra I (BI1201221964G) - Boots kernel, but it won't run init (mmc timeout waiting for interrupt)
 
** 8&nbsp;GB SDHC Class 6 Extreme (BI1101116253G)
 
** 8&nbsp;GB SDHC Class 10 Extreme (BI1108716254G)
 
** 8&nbsp;GB SDHC Class 10 Extreme (BI1201416254G) - Still doesn't work with Debian Wheezy beta (2012-06-18)
 
** <del>8&nbsp;GB SDHC Class 10 Extreme (BI1201516254G) [[http://www.amazon.co.uk/gp/product/B00422FBJ2 amazon.co.uk]]+amazon.fr</del> works with Wheezy 19/09/2012
 
** 8&nbsp;GB SDHC Class 10 Extreme (BI1200916252D/SDSDX-008G-X46) - Tried with Debian "Squeeze"(19/04/2012), Debian "Wheezy"(18/06/2012) and Arch Linux(13/06/2012). None works. With Debian "Wheezy" Green LED stays ON continuously, with the other two it turns on very faint.
 
** 8&nbsp;GB SDHC Class 10 Extreme Pro- Works with updated kernel/firmware, stock debian6-19-04-2012 boots kernel, but it won't run init (mmc timeout waiting for interrupt).
 
** <del>16&nbsp;GB SDHC Class 10 Extreme (30&nbsp;MB/s HD Video) (SDSDX3-016G-X46) - Doesn't boot with debian6-19-04-2012.img, or newer firmware (tested 2012-06-17).</del>
 
** 16&nbsp;GB SDHC Class 6 Ultra (BL1202021933G)
 
** 16&nbsp;GB SDHC Class 6 Ultra I (BL1205921933G) - Boots kernel, but it won't run init (mmc timeout waiting for interrupt)
 
* '''Silicon Power'''
 
** 8&nbsp;GB SDHC Class 10 (SP008GBSDH010V10) - Boots kernel, but it won't run init (mmc timeout waiting for interrupt) - Tested 20/11/2012, 2012-10-28-wheezy-raspbian.img with Nov 20 kernel.
 
** 32&nbsp;GB SDHC Class 6 (LS2N732GQON03ASP) - boots debian6-19-04-2012.img, but frequent slow response / system hangs.
 
 
 
* '''TDK'''
 
** 4&nbsp;GB SDHC Class 6 (S404G1041) - Tried (end May 2012) with new kernel.img and start.elf [https://github.com/raspberrypi/firmware/tree/master/boot] but still won't run init.
 
** 4&nbsp;GB SDHC Class 6 (S404G1046) [Barcode: 4 902030 784447] - Tried (4th June 2012) with debian6-19-04-2012.img and with replacement kernel.img and start.elf from github [https://github.com/raspberrypi/firmware/tree/87a04c0be0c05e20f94f223183a0310b37c9bd89/boot] but still got 'Error -84' and 'Kernel panic - not syncing: No init found'
 
 
 
* '''Transcend'''
 
** 2&nbsp;GB MicroSD (MMAGR02GUECA-MB) - reads fine initially after image was written on a PC, gives mmc0 timeout errors reading back data after writing a large amount (in this case with 'pacman -Syu').  Still seems to work, but is *very* slow after this happens, even across reboots.
 
** 32&nbsp;GB MicroSD (TS32GUSDHC4) - Doesn't boot.
 
** 2&nbsp;GB SD (6451AG 2G O2DS1)
 
** 16&nbsp;GB SD Class10 (TS16GSDHC10U1) - Doesn't Boot, show that "kernel panic - not syncing attempted to kill init"
 
* '''Veho'''
 
** 4&nbsp;GB SDHC Class 6
 
* '''Verbatim'''
 
** 16&nbsp;GB SDHC Class 6 (47178) - Raspbian Pisces RC3 - boots, but after login: mmc timeout waiting for interrupt
 
** 8&nbsp;GB microSD Class 10 (44012) - ArchLinux - boots, but after system update develops segmentation faults
 
** 8&nbsp;GB SDHC Class 10 (Premium) - Tested with September release of Raspbian and Debian Wheezy - both fail to boot with mmc errors.
 
 
 
The usual warnings against less reputable sellers (such as Ebay merchants) apply.
 
 
 
 
 
Note that the following error is sometimes accompanied with a non-working SD card after booting (on Debian):
 
 
 
mmc0: timeout waiting for hardware interrupt
 
 
 
=== Benchmarks ===
 
 
 
* http://www.sakoman.com/OMAP/microsd-card-perfomance-test-results.html
 
* http://usbspeed.nirsoft.net/usb_drive_speed_summary.html?o=11
 
* http://www.raspberrypi.org/phpBB3/viewtopic.php?f=2&t=4076
 
* http://forum.xda-developers.com/showthread.php?t=1005633 (It doesn't originate from Raspberry Pi, but it is very related.)
 
  
 
== Foreign Language Translations ==
 
== Foreign Language Translations ==
Line 2,848: Line 813:
 
{{Template:Raspberry Pi}}
 
{{Template:Raspberry Pi}}
 
 
 +
nbsp;V 1nbsp;V 1000

Latest revision as of 03:43, 28 July 2017


Contents

RaspPi.png Back to the Hub


Hardware & Peripherals:

Hardware - detailed information about the Raspberry Pi boards.

Hardware History - guide to the Raspberry Pi models.

Low-level Peripherals - using the GPIO and other connectors.

Expansion Boards - GPIO plug-in boards providing additional functionality.

Screens - attaching a screen to the Raspberry Pi.

Cases - lots of nice cases to protect the Raspberry Pi.

Other Peripherals - all sorts of peripherals used with the Raspberry Pi.


A note about this page: For USB devices, please specify if they required a powered hub

Notes

19-Apr-2012: Now that the Model B board is shipping, details added should relate to this board and the default Debian distribution unless stated otherwise. A suggested suffix markup scheme is as follows:

  • (A) - Relates to model A production board
  • (B) - Relates to model B production board
  • (!) - Information from alpha and beta board days -- beta board verified peripherals should still apply to production boards for the most part, but the alpha board is fairly different
  • No markup - relates to all production boards

Discuss: http://www.raspberrypi.org/forum/?mingleforumaction=viewtopic&t=247

If you are adding to a product list it would help clarity if entries are kept/added in alphabetical order.

Power Usage Notes

Warning Warning: Adding peripherals may increase the loading on the power supply to your board and this, in turn, may affect the voltage presented to the Raspberry Pi. If the Raspberry Pi's supply voltage falls below a certain value (anecdotally stated as around 4.75 V), or it begins to fluctuate, your setup may become unstable. There is a Wiki section about this issue which is worth a read.

Model B Hardware Revisions and USB Power limits Hardware Revision 1.0 The original Model B board had current limiting polyfuses which limited the power output of each USB port to approximately 100 mA. USB devices using more than 100 mA had to be connected via a powered hub. The Raspberry Pi's PSU was chosen with a power budget of 700 mA of which 200 mA were assigned to the USB ports, so the Raspberry Pi's (poly)fuses were designed only for devices up to 100 mA, and typical 140 mA polyfuses will have as much as 0.6 volt across them when drawing currents near the 100 mA limit. As a consequence the USB ports are only directly suitable for "single current unit" USB devices which, according to USB specifications, are designed to work with just 4.4 Volt. Not only do non single current unit devices draw more current (causing greater Voltage drops, and greater stress on the fuses), they also might require 4.75 Volt to work.

Model B Hardware Revision 2.0 and Revision 1.0 with ECN0001 change This had the polyfuses removed, removing the 100 mA current limitation for each USB port (but leaving the main fuse F3 intact). Users should still ensure their power supply can power the Raspberry Pi and the USB peripherals. Revision 2.0 was released in August 2012. Warning Warning: Because the polyfuses have been removed, back feeding of the PI, by applying power via its normal USB output, can damage D 17 if triggered by an over-voltage, and so lead to consequential over-heating. This can be discovered by melts, scorching, smoke or worse.[1]

Linux Driver Issues

Shortly after the Raspberry Pi was released it was confirmed that there were a number of issues with the Linux USB driver for the SMSC95xx chip. These included problems with USB 1.x peripherals that use split transactions, a fixed number of channels (causing problems with Kinect) and the way the ARM processor handles the SMSC95xx interrupts. [2] [3] A large number of fixes were included in the 2012-08-19-Wheezy-raspbian Linux image.

Powered USB Hubs

This section has been moved to a separate page. See RPi Powered USB Hubs

USB Remotes

  • The FLIRC USB dongle allows the use of any remote control with your Raspberry Pi. Configure the device on your desktop PC, then simply plug into your Pi for a perfect media center companion. Available from Pi Supply and The Pi Hut
  • ASUS TV FM Remote IR - ID 3353:3713 - works. Receiver connected to an USB Hub. Tested with archlinux in X. It works also as pointer (pressing "Toggle" button)
  • ATI Remote Wonder (X10 Wireless Technology, Inc. X10 Receiver) — ID 0bc7:0004 — appears as a joystick-like 2 button mouse and a 0-9 keypad without drivers on console and X.
  • iPazzport mini 2.4 GHz wireless keyboard and touchpad.
  • Pan.Code D1000 - 2.4GHz Wireless keyboard and touchpad.
  • PKB 1800 Wireless Smart Pad ad Mini Keyboard. The pad works as a mouse, but not multi touch features. The keyboard works.

USB Keyboards

This section has been moved to a separate page. See RPi USB Keyboards

USB Mouse devices

This section has been moved to a separate page. See RPi USB Mouse devices

USB Real Time Clocks

  • Cymbet
    • Cymbet CBC-EVAL-06 USB Real Time Clock (FT2232 to SPI to RV-2123)

Device information at http://www.cymbet.com/pdfs/DS-72-22.pdf Code to access the RTC from Linux: https://github.com/owendelong/Cymbet-RTC Does not require a powered hub.

Internet

USB Wi-Fi Adapters

This section has been moved to a separate page. See RPi USB Wi-Fi Adapters

USB Bluetooth adapters

This section has been moved to a separate page. See RPi USB Bluetooth adapters

USB Ethernet adapters

This section has been moved to a separate page. See RPi USB Ethernet adapters

USB 3G Dongles

Huawei

  • E1750 installation instructions
  • E173
  • E1820 Works on Raspbian with Sakis3G
  • E220 installation instructions
  • E353 HiLink Works on Raspbian
  • E160 (AT commands only)
  • E169, E620, E800, (12d1:1001) - works on Raspbian Wheezy, details here
  • E303 - works with Raspbian Wheezy 2015-02-16 out of the box, will be recognized as network-adapter [ethX]. usb_modeswitch may be used to configure it as a serial modem, so that tools like sakis3g (mobile connection) and gammu (SMS) have a better control over it (note: be sure to download a version of Gammu newer than 1.37.0 so that it is fully supported)

Sierra Wireless

  • AirCard 250u works with wvdial/network manager
  • AirCard 320u (0f3d:68aa) works in WWAN mode, driver provided by the kernel. Tested on Arch.
    • Kernel version 3.10 has a bug that causes the WWAN interface to never be in RUNNING state (no carrier). Use 3.6 kernel instead.
    • AT command guide can be found here
    • for GPS to work you have to enable it. First, setup the modem (guide here) and after that enable NMEA output by passing nmea=1 parameter to the sierra kernel module. Warning! Enabling NMEA output may cause the modem to drop connections / restart itself. This is probably related to higher power drain. This may not be the issue when a powered hub is used.
  • 307 Works fine with Sakis3G script. The connection LED does not change its state after establishing a connection but the same behaviour on a normal linux system.
  • AirCard 340u (Netgear/ATT Beam) works with latest GobiNet/GobiSerial code on Raspbian and 3.10.25+ kernel. Requires firmware update from Netgear to disable Windows 8 support and make it autoconnect. guide here.

ZTE

Others

  • Franklin U600 from Sprint / VirginMobile
    • Use usb_modeswitch and vendor 0x1fac and product 0x0150/0x0151
  • Digicom Internet Key 7.2 HSUPA MU372-L01 [4]

Tested on Raspbian and Archlinux. Detected as 230d:0001. Works with cdc_acm driver. Install usb_modeswitch. There are 2 "com ports"( /dev/ttyACM0 and /dev/ttyACM1 ) . Tested with Network Manager.Works also perfectly with SAKYS3G [5] tools (!! led is always off !!) and wvdial. A working wvdial.conf: http://ubuntuforums.org/showpost.php?p=10361881&postcount=28 . (for example for Vodafone IT , replace Init3 with this: Init3 = AT+CGDCONT=1,"IP","web.omnitel.it" and replace line Modem = /dev/ttyUSB0 with Modem = /dev/ttyACM1 ) and run with wvdial voda .

  • Vodafone MD950 (1dbc:0005) - is working on RPi (Raspbian Wheezy) but not out of the box, more details here.

USB 4G Dongles

Huawei

  • Huawei E398 LTE USB Rotator Mobile Broadband
  • Huawei E3372 LTE USB stick

USB Sound Cards

You will usually want the alsa package for sound. In the Debian image for Raspberry Pi (and possibly other distributions) USB sound cards are prevented from loading as the first sound card, which can be an annoyance if it's the only device you have. To disable this behaviour edit /etc/modprobe.d/alsa-base.conf and comment out the last line; options snd-usb-audio index=-2 . If you are not user pi you may need to add your username to the audio group thus: sudo adduser yourusername audio (user pi usually belongs to this group anyway).

Databases of supported sound cards

Class compliant USB sound cards

Any USB1.1 audio interface that is class compliant should work with Linux, same goes for USB2.0 interfaces that adhere to the current USB audio standards. There are some interfaces that are supported in Linux while they do not comply to the standards because specific quirks have been added to the USB Linux drivers. To verify if your interface is supported search for a manual of your interface and check if it needs drivers to run under Windows/Mac. If the manual explicitely mentions no drivers are needed the interface is almost surely a class compliant device. When in doubt check the aforementioned databases.

Troubleshooting

If you encounter problems setting up your USB soundcard check the RPi Wiki article in the linuxaudio.org Wiki: http://wiki.linuxaudio.org/wiki/raspberrypi

  • Bulleted list item

USB IR Receivers

  • The FLIRC USB dongle allows the use of any remote control with your Raspberry Pi. Configure the device on your desktop PC, then simply plug into your Pi for a perfect media center companion. Available from Pi Supply, The Pi Hut and Buy Raspberry Pi Australia
  • SMK Manufacturing, Inc. eHome Infrared Receiver (Works out of the box with OpenELEC)

USB Radio devices

  • FM Radio
    • ADS InstantFM Music - FM radio tuner works fine under Debian.

USB TV Tuners and DVB devices

  • August
    • DVB-T205, based on rtl2832u chipset, worked with this driver on older 3.2 kernel. Couldn't get same device working reliably on current kernel. (On the older 3.2 kernel it worked with Saorview (Irish DTT service), both HD & SD.)
  • Derek?
    • TV28T v2 USB DVB-T & RTL-SDR Receiver, RTL2832U & R820T Tuner, MCX Input. DVB-T works with OpenElec 4.2.1 connected to the PiHub, tvheadend backend + frontend, finds all expected, non-encrypted channels in the south of Germany. I did not try to use the remote.
  • DVBSky
    • Mystique SaTiX-S2 Sky USB: Scanning/watching SD and HD works via vdr and streamdev plugin, watching on the Raspberry Pi directly is laggy as hell. DVB-USB and I2C support must be enabled in the kernel. Needs drivers/firmware from here.
  • Sundtek
    • Sundtek MediaTV Digital Home
    • Sundtek MediaTV Pro
    • Sundtek SkyTV Ultimate
    • DVB-C, DVB-T, DVB-S/S2: digital TV works, streaming to Windows / Linux is no problem. Easy installation English
  • Hauppauge
    • Hauppauge NOVA-T Stick (Revision 70xxx) DiBcom DiB0700 chipset, requires powered hub.
    • Hauppauge NOVA-TD Stick (Revision 52xxx) DiBcom DiB0700 chipset, requires powered hub.
    • Hauppauge WinTV-HVR-1950 (tested analog tuner with omxplayer, tested Digital OTA with MythTV)
    • Hauppauge WinTV-HVR-950Q (tested Digital OTA with TVHeadend in Raspbian)
  • K-World
    • K-World UB499-2T Dual DVB-T USB Tuner. IT9137 chipset. With no other USB devices connected Raspberry Pi can just about power this stick. IR and supplied remote work with XBMC.
  • Technisat
  • TECHNOTREND
    • TT-TVStick CT2-4400 USB Fernbedienung rev2. DVB-T works with OpenElec 4.9.4 BETA connected to the PiHub, tvheadend backend + frontend, finds all expected, non-encrypted channels in the south of Germany. DVB-C also works, finds around >30 TVs and >100 radio stations. I did not try to use the remote, nor did I listen to any radio station. TV works, SD channels are ok, HD channels jitter. tvheadend backend crashes often within OpenElec 4.9.4 BETA, but restarts, so still buggy but looks good(BETA!). It did not work out of the box with the stable OpenElec 4.2.1.
  • Terratec
  • Generic
    • DVB-T USB Dongle (Silver casing), based on AF9015 chipset.
    • DVB-T USB Dongle, based on RTL2832 FC12 (HD/SD), IR was detected, but it is not tested.
    • HDTV USB DVB-T dongle, based on IT9135. This tuner comes in two revisions. Revision is printed on PCB.
      • rev. 1.0; should work with 3.2+ kernel, need confirmation.
      • rev. 2.0; works with kernel 3.6.11, without a powered hub. This tuner also requires a firmware (dvb-usb-it9135-02.fw) which can be downloaded from this page. It's in Hungarian, so google translate or equivalent is recommended. The remote also works.
        According to this post, there may be issues on some software configurations when using omxplayer.

USB Video / Frame grabbers

  • EasyCAP DC60 (STK1160 chip) - works out of the box for older versions of Raspbian. If you're getting grey stripes see this tutorial
  • EasyCAP (UTV007 Fushicai chip) - works after driver compilation - see instructions at this link. remember to use older Raspbian version.
  • Hauppage HVR 1900

USB Webcams

This section has been moved to a separate page. See RPi USB Webcams

USB GPS devices

  • Columbus
    • Columbus V-800 (MediaTek (MTKII) 3329 GPS chipset) - does not require powered USB hub. Works on Wheezy (using gpsd & gpsd-clients)
  • Royaltek
    • Royaltek RGM 2000 SiRF2 using the included serial (TTL) to USB - converter (Prolific pl2303-chip)
  • Garmin
  • GlobalSat
    • GlobalSat BU-353 Does not require a powered hub, works fine when directly plugged into the Raspberry Pi. On Raspian, requires the gpsd and gpsd-client packages. For some reason, the gpsd daemon does not always start correctly on boot. You may need to do something like the following to manually restart it:
      sudo killall gpsd; sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock
    • GlobalSat BU-353-S4 supports two protocols: NMEA, and SiRF v4. NMEA works fine, but SiRF v4 isn't compatible with "gpsd"'s SiRF v3 interpreter, resulting in a greatly reduced data rate (as low as four location fixes per hour). To keep "gpsd"'s autoconfiguration from putting the receiver in SiRF mode, you'll need to pass the "-b" flag when starting "gpsd".
  • Wintec
    • WBT-200: No problem on Debian
  • Holux
    • Holux M-215: Works fine on Arch, uses Silicon Labs CP210x RS232 serial adaptor driver
  • Bluenext
    • Bluenext BN903S: No problem on Debian image (19-04-2012).
  • U blox NEO 6 - works well, connects via GPIO (serial console). Info here and here.

USB UART and USB to Serial (RS-232) adapters

A USB UART adapter is used to access the serial console of the Raspberry Pi from a development host such as a laptop or desktop PC. The USB end connects to the PC and the UART header end connects to the USB. While it is possible to connect the USB end to another Raspberry Pi, this configuration has not been tested unless explicitly mentioned against an individual entry below.

Working USB to Serial Adapters

  • FTDI (Future Technology Devices International Limited)
    • FT232 chip based adapters works for some people, but others find it hangs Linux when the port is opened. The module is ftdi_sio.
    • FT232R USB UART works out of the box between Raspbian Wheezy and OS X Mavericks (Product-ID: 0x6001, Manufacturer-ID: 0x0403, Maximal Speed: 12 MBit/s, Maximal Power Consumption: 90 mA).
    • FT2232D dual RS232/FIFO works (used in various JTAG devices)
  • Belkin
    • F5U409 Works OOTB; does not support speeds above 115,200, so you can't use it for DMX or other high-speed protocols.
  • Prolific
    • PL2303 chip based adaptors works fine on latest Debian tested with minicom, gtkterm and screen.

A USB to Serial (RS-232) adapter is used the other way around, ie. the USB end connects to the Raspberry Pi and the RS-232 end (DSUB-9 or DSUB-25 pin) to the other device which may be another computer, (old) modem or printer, or some electronic test equipment.

  • "Best Connectivity" (Possibly also sold under the "Newlink HQ" or "Kenable HQ" labels)
    • FG-U1232-PL2 Based upon the Prolific PL2303X chipset and listed by lsusb as ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port. Appears as /dev/ttyUSB0, and requires the user to be a member of the dialout group (which pi is for Raspbian Wheezy). Initially tested using an old RS Datalinker setup in "loopback" mode via microcom upto 9600 baud, and gtkterm after installing that from source code. All handshake lines toggled as expected and no characters were lost. Subsequently gtkterm was used to check bi-directional communication with an ancient brother EP44 electronic typewriter (as a printer/dumb terminal) at 1200 baud. Signal lines were again monitored with the Datalinker.
  • "PL2303HX USB to RS232 TTL Converter Adapter Module" on dx.com: http://dx.com/p/pl2303hx-usb-to-rs232-ttl-converter-adapter-module-164590
    • Based on the Prolific PL-2303HX chipset. Listed by lsusb as ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port. Appears as /dev/ttyUSBX with GUID dialout so your user has to be in that group. If not, sudo usermod -a -G dialout yourusername will add your user to the dialout group. Works great with screen /dev/ttyUSBX 115200 to connect from your workstation to your RPi.

Problem USB to Serial Adapters

HL-340

  • CH340 Chipset - Currently not supported by RPi but there is a patch of kernel code here, but it is for a 2.X kernel. If you find you have bought one of these, then it may work under Windows, but as of writing there is no support for RPi. Otherwise you can have a go at getting the patch to work.

USB Multi-Card Readers

Working USB Multi-Card Readers

  • US Robotics USB 3.0 All-In-One Multi-Format Card Reader (Product # USR8420) Accepts 5 cards simultaneously
    • SD/MMC + MS/MS PRO or DUO/DUO PRO + CF/MD + SM + SD/MMC or MS/MS PRO. Useful for backing up cards containing other OS Distros
  • Generic (Nintendo branded)
    • identified as "14cd:8123 Super Top SD MMC Reader" (B)

Problem USB Multi-Card Readers

  • Generic
    • Card reader based on NEODIO ND3260-LD chip, identified as "0aec:3260 Neodio Technologies Corp. 7-in-1 Card Reader", fails after a few seconds with all access lights blinking. (B)

USB Smart-Card Readers

Working USB Smart-Card Readers

  • Vasco DIGIPASS 905. Works out of the box without any extra drivers. Does not require powered USB hub.

Other, exotic USB devices

Joysticks / Joypads

  • Microsoft
    • Xbox360 Controller (045e:028e): works. Tested with archlinux, connected to an USB Hub, used as "mouse" in X, package xf86-input-joystick
  • Logitech
    • Dual Action: works, connected directly to the Pi.
  • Ion
    • Go Pad: works. Tested on Raspbian Wheezy (release 2014-01-07), connected to on-board USB port (Model B rev. 2).
  • VZTEC
    • USB Double Shock Controller Game Pad Joystick VZ-GA6002: works. Tested on RetroPie V2.3, connected to on-board USB port (Model B+).

Numpads

  • Conceptronic / Holtek
    • USB numpad (04d9:a02a): works. Tested with archlinux, connected to an USB Hub
  • Speedlink SL-7430-SGY
    • USB numpad (04d9:1603, HT82M99E Holtek chip inside): works. Tested with Raspbian “wheezy”
  • GreenAsia Inc. (USB 18-Key Silicone Numeric Keypad)
    • USB numpad (0e8f:0022): works. Tested with Raspbian “wheezy”

USB to Parallel Port/Printer Adapters

  • Prolific
    • PL2305 Chipset with Centronics 36w connector. Originally purchased for use with a netbook and connected to an old Canon BJC-250 printer. Worked fine under RISC OS Raspberry Pi with its in-built BJC-250 driver. Could not install the CUPS drivers etc. for Wheezy-Raspbian initially, but was able to do so for Wheezy-armel. Once I'd updated/upgraded Wheezy all was fine.(See notes at CPM-Spectre-Pi...USBtoParPrntAdapter for more info. and also a CUPS/Wheezy installation guide)

USB to IDE/SATA

  • JMicron Technology
    • JM20337 USB to SATA/PATA Combo Bridge (152d:2338) - works on Raspbian and Arch. The hard drive requires an external power supply.
  • Nippon Labs
    • 2.5" SATA HDD USB Adapter with silicone HDD sleeve. Model: USB-ADT-25SATA. Works on powered Hub, not directly to Raspberry Pi. Built-in "Y" power adapter. Does work direct on some ver2.0 boards if used with 5.25 power supply, or Y adapter

CAN Bus

Home automation

  • Tellstick (www.telldus.com), installation instructions
    • Depends on libftdi1

Weather station

  • Oregon Scientific WMRS-200 : Work out of the box (tested with Raspbian & wview)

One-Wire

  • PCsensor
    • USB9097 (1a86:7523): works out of the box but issue with LAN after a few hours, no problem after a firmware update. Identify's as "QinHeng Electronics HL-340 USB-Serial adapter" Tested with raspbian/wheezy + domotiga & digitemp directly to USB port & 4 sensors connected via a '1-wire hub'. Claims to be 'fully replace DS9097, DS9490 of MAXIM'. Simple and cheap solution to measure temperature.

Touch Screen

  • ACER T230H touch screen [6]This link is Broken
    • USB TS identifies as "Quanta Computer, Inc. Optical dual-touch panel", module hid_quanta
    • Seems to draw over 200 mA from USB!
  • SainSmart 3.2 touch screen [7]
    • 320*240
    • 3.2 inch
    • SSD1289:240 RGB x 320 TFT Drive
    • Video: Raspberry Pi with a 3.2" TFT with Touch control [8]
    • Tutorial: Raspberry Pi with a 3.2″ TFT with Touch control [9]

Floppy Disk Drive

  • Samsung USB Floppy Drive SFD-321U/HP
    • I suppose a floppy drive might be considered exotic nowadays!
    • LSUSB lists it as Samsung Electro-Mechanics Co. Floppy Disk Drive
    • Only tried connected to a powered USB hub, as the drive is labelled 5 V at 0.5 A on a Raspberry Pi running Debian Wheezy.
    • tail -f /var/log/syslog looking for mount device when plugged in, came up as SDA in testing.
    • sudo mkdir /media/floppy
    • sudo mount /dev/sda /media/floppy
    • Contents of floppy now available in /media/floppy
    • To remove drive, ensure no sessions have the floppy directory as the current working directory.
    • sudo umount /media/floppy
  • Y-E Data model HU-35EF
    • Requires a powered hub and manual mounting/unmounting like the Samsung drive above.

USB Missile Launcher

  • USB Missile Launcher / Rocket Launcher sold in UK by Marks and Spencer, but it is also sold under a range of other names.

USB Docking Stations

  • StarTech USB 3.0 to Dual 2.5"/3.5" SATA HDD Dock (SATDOCK2U3GB)
    • This is an externally powered dual sata HDD docking station, which has USB2.0 compatibility with the Raspberry Pi.
    • Tested with latest Raspbmc and Debian Wheezy Raspbian, 3.1.9+ #168
  • Icy Box USB 3.0 to Dual 2.5"/3.5" SATA HDD Dock (IB-120StU3)
    • Externally powered dual HDD dock, USB 2 compatible.
    • Tested with Slackware ARM 14.0 and drives in both slots, just show up as separate SCSI disks.

USB RFID Reader

  • Unbranded 125 kHz EM4100 RFID reader from eBay sellers (< £7), the one with a Windows logo on (easily scratches off for Linux users).
    • Initially would not work when plugged in directly to Raspberry Pi. Worked when connected via an unpowered Trust hub. Worked after Raspberry Pi was modified with 10K resistors over the USB polyfuses (warranty invalidated). Probably would work fine with powered hub.
    • Sends a 10 digit string to current window or console as if it was a keyboard. Can be captured independently of keyboard using Linux event interface (/dev/input), but the kernel in current distributions does not have CONFIG_INPUT_EVDEV selected so kernel rebuild is necessary.

JTAG

  • FTDI2232D dual RS232/FIFO based JTAG (e.g. SheevaPlug JTAGKey USB-ID 9e88:9e8f)
    • works using the Raspberry Pi as a development host

Tinkerforge Bricks and Bricklets (http://www.tinkerforge.com)

Thermometers

  • TEMPer1 (id: 0c45:7401)

Fingerprint Scanners

Futronic

Single finger scanners Futronic FS80 and FS88 tested - they work well with Raspbian. Example of captured fingerprint here: Media:Futronic_fingerprint_example.png

To make it working deploy the Futronic libScanAPI on your Raspberry Pi (example code and instructions included): Media:ScanApi_armlinux_RPi_gnueabihf_gcc472_update1.zip ‎

UPDATE: Futronic has released an updated API. This works with their newer 'H' model scanners (updated CMOS). This means the FS80H and FS81 (the OEM version of the FS80H) will now work with the RPi (I tested this myself). Media:ScanAPI_v823_armlinux_libusb0.1.12-bcm2708_gnueabihf_raspbian-472.zip

PS2 / AT to USB Converters

Note that although the adapter might work, PS/2 keyboards were not designed to be low power USB devices, so they might not meet the requirement to work with considerable lowered supply voltage (4.4 volt) provided by the USB ports of the raspberry PI. These keyboards should work when powered by a powered hub.

Tested PS2/AT keyboards

All above tested with the famous "blue cube" on a powered USB hub.

  • IBM Model F (please note requires an additional AT to PS2 converter)
  • Dell AT101w
  • Northgate Ominikey Ultra T (please note requires an additional AT to PS2 converter)
  • 04d9:1400 Holtek Semiconductor, Inc. PS/2 keyboard + mouse controller
    • Working: Ipex RT215KTW PS/2 keyboard
    • Not working: HP SK-2502 PS/2 keyboard (gets power, but it does not init - three LEDs remain permanently lit. Keyboard + Holtek converter work on a Linux PC, although this keyboard doesn't work with some native PS/2 ports.)

Power Switches

The Raspberry Pi does not have a power on/off switch as standard (it does have a reset switch), however some add on boards have been developed to cater for this need.

  • The Pi Supply Switch is an on/off power switch for the Raspberry Pi which includes a hard on and off switch and a soft shutdown switch for the Pi, making it easy to manage power on your Pi. They were recently successfully funded on Kickstarter.
  • RemotePi Board
    • The RemotePi Board is an intelligent infrared remote controlled power switch add-on board for the Raspberry Pi. It allows to switch power on and off using any button (configurable in learning mode) of an existing standard IR remote. Power is only cut after notifying the OS and giving it time to shut-down. It is mainly intended to remote control (using LIRC) and power off/on a mediacenter system. i.e OpenELEC, Raspbmc, XBian, RasPlex, Raspbian. The board is compatible to simple GPIO IR receiver and piggy backs onto the Raspberry Pi, no soldering required. For more information click here.

Power adapters

The Raspberry Pi uses a standard Micro USB (type B) power connector, which runs at 5 V. Generally you can use a MicroUSB to USB cable and then either power the Raspberry Pi directly from your main computers USB ports (if they provide enough power), or by using a USB to Mains adapter. A number of mobile phones use MicroUSB power cables, and these are compatible with the Raspberry Pi in most cases. Below is a list of power adapters known to work.


Working power Adapters

There is now a 5.25V 1500mA power supply manufactured specially for the Raspberry Pi to account for voltage drop due to the high current draw of the Raspberry Pi when compared to typical (phone charging etc.) duties.
Available in UK, EU, USA and AU varieties from Pi Hut and Pi Supply


  • Adafruit
    • 5.25 V 1 A Model 501 (Newark 44W4932) USB 110-240 VAC power supply [4.99-5.01 V @ T1/T2 with 100 mA BT and/or mini wireless-n on RPi USB ports]
  • AlcaPower
    • 5 V 2.5 A Model AP5A - Charger/switching with 7 connectors(also Microusb)
  • Ansmann
    • Dual USB charger slim, Model-Nr. 1201-0001
  • Apple
    Note that apple designs its charger products to work optimally as chargers. In practice this means that apple chargers drop their output voltages somewhat with output current, so that the charging circuits do not need to dissipate more heat than is strictly necessary. Because of this, and although many people have reported apple products to power their basic PI setup reliably, its still not an optimal choice for a PI system that uses power hungry USB devices. Also, because of the popularity and high price of these chargers there are many very sub standard, but almost impossible to recognize as fake copies on the market, and some of these fakes are about the worst things you can try to power your PI with! Not only do they not work, they may actually be dangerous to use!
    • 5 V 2.1 A USB charger for iPad2, model A1357
    • 5 V 1.0 A USB Charger for iPod
    • 5 V 1.0 A USB Charger for iPhone 4
  • Amazon
    • 5 V 0.85 A USB charger for Kindle
    • 5 V 2 A Mains to USB A adaptor, Branded "CostMad"
  • Artwizz
    • 5 V 1.0 A USB charger (Model: YFAR23073001)
  • Asus
    • 5 V 2.0 A USB charger for Google Nexus 7
  • Bandridge
    • 5 V 1.0 A Mobile Phone Charger (Model: BPC3102EC)
  • Belkin
    • 5 V 2.6 A 4 port Ultra-Slim Desktop hub (Model F4U040) (Raspberry Pi running from USB hub port)
    • 5 V 2.5 A 4 port USB Hub (Model F5U404) (Raspberry Pi running from USB hub port)
    • 5 V 3.5 A 7 port USB 2.0 Mobile Powered Hub (Model F4U018) (Raspberry Pi running from USB hub port)
    • 5 V 3.5 A 7 port USB Hub (Model F5U706) (Raspberry Pi running from USB hub port)
    • Mini Surge Protector Dual USB Charger (Model BZ103050-TVL)
    • Universal USB Wall Charger (5 V 1 A) (Model F8Z222uk)
    • Universal Home Charger with Micro USB ChargeSync Cable (10 Watt/ 2.1 Amp) F8M667tt04 link
  • Blackberry
    • Charger for Pearl Flip 8220, Bold 9600 (B)
    • Charger for Tour 9630
    • 5V 1.8A "Folding Blade" Micro USB Tablet charger Part #: HDW-34724-001 Model #: AD8213HF (works with model A w/ camera + Wifi)
    • 5 V 0.7 A Model PSM04R-0500CHW1(M), RIM Part Number HDW-17957-003 (B)
    • 5 V 750 mA Model RIM-C-0004aDUUUC-001, RIM Part Number HWD-24481-001 (comes with Blackberry 9300)
    • 5 V 750 mA Model RIM-C-0004ADUUS-001 035D, Single port plug. (Tested with USB B to Micro USB cable from Logitech H760 Headset)
    • 5 V 2 A Model PSAC10R-050QT, RIM Part Number HDW-34725-001
    • 5 V 550 mA curve 8520 charger works with raspberry pi Model B Board v. BS1233. It does not work with Raspbmc image.Symtoms are frequent key board and external hdd disconnects.
  • CoolPad
    • Model: CYSK10-050200 fast charger with 5V 2000mA output, tested with USB WiFi, USB flash drive and USB wireless KB&MS connected. RPi users in China mainland can use this power adapter.
      Encounters power loss when 4-port USB 3.0 hub is connected.
  • Deal Extreme
  • Dell
    • USB Hub integrated in Dell monitors (B)
  • DLO
    • 5 V 1.0 A PowerBug (Model: SP05001000-A) Powers Pi, Wifi dongle and Webcam
  • The FX Factory
    • 5 V 1 A (1.2 A max) AC Travel Charger Model KJ-USB Mains. Typically provides 4.9 V at 1 A [1]
    • 5 V 2x1 A Dual Charger Model TR9202-MICRO. Typically provides 4.8 V at 1 A per output. Can be used to power a Pi and, via a separate cable, a USB 4-port hub [2]
  • Garmin
    • 5 V 1 A charger (Model: PSA105R-050Q) supplied with Garmin Edge 800 GPS. Requires a USB-A to MicroUSB-B cable. Belkin 6 ft cable (F3U151B06) works.
  • Gembird
    • 5 V 2 A Universal USB Charger (Model: MP3A-UC-AC5). Test: 1080p TV (1xHDMI), USB Wi-fi adapter (1xUSB), wireless keyboard and mouse (1xUSB). Results: ~5.3V, works without any problems (own usb cable required).
  • Globe Electric
    • 2-Outlet Tap with Surge Protection and 2 USB Chargers (46082). Rated at 1000 mA. 120 V systems only.
  • Griffin
    • Power Block Model P2417. 5 V 2.1 A
    • Power Block Model P1190R2 Two USB 5 V Outputs, 1 A each
  • Hama
    • 1000 mA Travel Charger for Micro USB universal (barcode nr: 4 007249 935854)
  • Hartig + Heiling GmbH & Co. KG
    • H+H SN 6 USB
  • HP
    • 5.3 V 2 A Charger for HP Touchpad (B)
  • HTC
    • 5 V 1 A TCP-300 USB phone charger (B)
    • 5 V 1 A TC B250 USB charger (HTC R/N: 79H00096-00M)
    • 5 V 1 A TC E250 USB charger (HTC R/N: 79H00098-02M)
  • i-box (Philex Electronic Ltd)
    • 5 V 1 A USB charger, 1 USB socket, no USB lead supplied, Model: 76971HS/02 (available from ASDA and others in the UK) (B).
  • IDAPT
  • Innergie
    • 15 W Dual USB Adapter. Model: mMini AC15. Output: 5 V, 3 A (max per port), 15 W max. Specification sheet
  • ICIDU
    • PI-707730 charger 5V 2.1A, sometimes drops current to ~1.3A during heavy use, but still enough to power the Pi.
  • Kodak
    • 5 V 1 A TESA5G1-0501200
    • 5 V 1.0 A K20-AM
  • König
    • 5 V 1 A PSUP-GSM01
  • Kuanten
    • Model SSA051F050100USU, 1A output
  • LG
    • 4.8 V 1 A Travel Adapter
    • 5.1 V 0.7 A Travel Adapter (Model: STA-U34WVI)
    • 5.1 V 0.7 A Travel Adapter (Model: STA-U12ER)
  • Logic
    • 4 port USB Hub (Model LP4HUB10). (Raspberry Pi running from USB Hub port, red power line (+5 V) inside hub cut) (B)
  • LogiLink
    • 5 V 2.1 A Switching power supply, model PA0040 (B)
  • Logitech
    • 5 V 1 A SDC115-USB Remote Control Charger and cable
  • Maplin Electronics
    • 5 V 1 A dual USB power supply, model number H25B-MT-K2
    • Micro USB Power Supply N19HX
  • Medion
    • 5 V 1 A USB power supply for OYO ebook reader
  • Microsoft
      • Zune Zune AC Adapter v2
  • ModMyPi
  • Motorola
  • Noname
    • 5 V 2.1 A KMS-AC09 4 port USB charger (B) [10]
    • 5.2 V 1 A MW-3NU10GT - no cable, but this one works well (1m): [11]
    • 5 V 1 A Model H-IP008 Serial No. H10T80L068
    • 5 V 1 A Travel charger Model MSH-TR-018A reseller1, reseller2
    • 5V 2A Mobile Charger For Galaxy S4 NOTE 2 N7100 N7000 With USB Cable(in India) Ebay.in
  • Novatel Wireless
    • 5 V 1.05 A Charger, model number SSW-1811, packaged with Verizon Wireless MiFi device
  • Orange
    • 5 V 0.7 A Charger for Orange San Francisco
  • Palm
    • 5 V 1 A Charger for Palm Pixi+ (B)
  • Pantech
    • 5.0 V 1 A CNR USB with LG DLC100 micro USB cable
  • Petzl
    • 5.0 V 1 A Charger that came with the Tikka core2 XP
  • Phihong
    • Switching Power Supply. Model: PSAC09R-050. Output: 5 V, 1.8 A, microUSB. Digi-key Link
  • Pi Supply
  • PortaPow
    • PortaPow UK Mains Wall Power Supply
  • PowerGen
    • PowerGen Dual Port USB 2.1A 10W AC Travel Wall Charger. Amazon Link
  • Rayovac
    • Universal USB Charger Model: PS69 100-240 VAC to 5 V 1 A (small cube w/folding plug) works w/wireless keyboard/mouse and mini-Wifi connected
  • RhoTech
    • RH-PS001 5V/2A, dedicated for Raspberry Pi, integrated MicroUSB cable. Stable with Raspbmc and WiFi card.
    • RH-PS002 5V/2.1A dual USB Power Supply.
  • RS Components'
    • HNP06UK (RS 7263069) Switching Adapter 5.0 V 1200 mA [12]
  • Samsung
    • 5 V 0.7 A Charger for Galaxy S model ETA0U10EBE
    • 5 V 0.7 A Charger for Galaxy SII
    • 5 V 1 A Charger for Galaxy SIII
    • 5 V 1 A Charger for Galaxy Nexus
    • 5 V 0.7 A Charger for Galaxy S Vibrant (SGH-T959)
    • 5 V 0.7 A Travel Adapter model ATADU10EBE
    • 5 V 1 A? Samsung C Series TV USB-port for external HDDs. Running stable with openelec
    • 5 V ?A (Unknown) Samsung Service Port (USB) on LN32A330J1DXZA 720p 32 inch HDTV
    • 5 V Unknown Ampere Samsung UA22D5000 & UA32D5000 TV USB Port. Test with Raspbian Wheezy, Raspbmc, and RPITC
    • 5 V 2 A charger for Galaxy Note 2; model ETA-U90EWE (works with cam module, Edimax wifi, SD card and analog audio out, even down to 4.62 V on model B rev 1).
  • Shun Shing
    • 100-240 VAC to 5 VDC 1 A USB power supply, model SP5Q-AU Jaycar
  • Sony Ericsson
    • 5 V 0.7 A Charger CST-80
    • 5 V 0.85 A Greenheart&#153; Charger EP800. Typically provides 4.8 V at 0.85 A [3].
  • StarTech
    • 4 Port USB 2.0 Hub Raspberry Pi can be powered just by plugging USB input into the Raspberry Pi, don't need power in micro USB port.
  • Travel Charger
  • Technika
    • 5 V 1 A USB Power Adapter, model MPASS01 (B)
  • Tinpec
    • 5 V 2 A USB Power Adapter model RG-AAC210, sold by Elro as AV323S
  • Trisonic
    • TS-CP600T - MICRO USB HOME & TRAVEL CHARGER (5 V, 800 mA) $3 at Daiso U.S. stores.
  • TruePower
    • U-Socket 5 V 2.1 A AC Receptacle with Built-in USB ports (2.1 A per USB port) model ACE-7169
  • Turnigy
    • TURNIGY 3A UBEC w/ Noise Reduction, connected to GPIO Pins
  • Voltcraft
    • SPS5-12W, 2500 mA, requires additional USB <-> miniUSB adapter/cable, works perfectly (bought from Conrad Shop)
  • Youse
    • Dual USB Wall Plate. Has a 2.1A "Tablet" port, a 1A "Phone" port and a US electrical outlet. Powers a Raspberry Pi 2 from the 2.1A "Tablet" port. Available from Five Below. Link
  • ZTE
    • ZTE Blade charger STC-A22O501700USBA-A 5 V 700 mA

Problem power Adapters

  • Nokia
    • 5 V 1.2 A AC-10A & AC-10E Chargers only provide 4.8V at TP1 & TP2
    • 5 V 1 A AC-16E Charger Provides only 4.7V across TP1 & TP2 when at idle
  • Masterplug
    • Masterplug Surge Protected USB Adaptor 2 x 1 A USB Polished Black - USB ports and Ethernet don't work with this adapter and some screen artifacts using HDMI.
  • Monoprice
    • 5 V, 2 A 3 Outlet Power Surge Protector Wall Tap with 2 Built-In USB Charger - some display artifacts, sometimes unable to find mouse, some failures to boot. Measured to less than 4.75 V between TP1 and TP2 when used with a Monoprice cable.
  • Sony Ericsson
    • 5 V, 850 mA EP800. Some failures to boot, Ethernet loops at boot.

Working external Battery packs (with 5 V regulated output)

  • Anker
    • Astro3 10000 mAh with dual 2 A USB output
    • Astro E7 2nd Gen (A1210) 26800 mAh with triple 4 A USB output
    • PowerCore (A1271) 20100 mAh with dual 2.4 A USB output
  • Duracell
    • PPS2 Instant USB Charger
  • EasyAcc
    • PB12000A 12000 mAh battery with 2.1 A USB output
  • Energizer/XPAL
    • XP18000 18000 mAh Power Pack
  • Generic - eBay no brand
    • 6000T Pocket Power 5000 mAh - eBay item 271009959140
    • Power Bank for iPad/iPhone 5000 mAh (looks the same as a New Trent IMP50D or TeckNet iEP380) - eBay item 280914455938
  • Mophie
    • 38113BBR Juice Pack Powerstation 4000 mAh: output 2.1 A max: included charging cable powers RPi, 7.5 hrs light use w/keyboard and mini-Wifi on RPi ports
  • iEnjoy
    • MyBolt 2600mAh
  • New Trent
    • iCurve IMP70D 7000 mAh (Approx 12 hours from full charge)
    • IMP120D 12000 mAh
  • Sinoele
    • Movpower - Power Bank 5200 mAh (8 hours with Wi-Fi active)
  • TeckNet
    • iEP387 Dual-Port 7000 mAh External Power Bank (The charging lead can be used to connect the Tecknet to the Raspberry Pi. Ran the Raspberry Pi with Wi-Fi dongle and wireless keyboard receiver for over 9 hours of light use.)
    • iEP390-9000mAh External Power Bank (The Power Bank has been verified working with RPI3 with on-board Wifi and HDMI out. Additionally, the Power Bank supplies power to RPI continuously without disruptions even when the Power Bank is connected / disconnected from charger -> it can be used as a cheap UPS)
    • iEP392 Dual-Port 12000 mAh External Power Bank (1 A port, ~16.5 hours)
    • Rayovac PS60 5 V 800 mAh
  • VINZO
    • Power Bank 5000 mAh Grey Output 5 V 1000 mA
  • Kodak Power Pack KP1000
  • Swees
    • Swees® 12000mAh Smart Power Bank (Output: 5V / 4.2A max)

LCD touch screen add-ons

Display adapters

Note that active converter boxes may draw power through the HDMI port, and thus will put an extra load on your PSU, and also increase the current running through the Raspberry Pi's primary input fuse. HDMI ports (and the raspberry PI) are designed so that they deliver a very limited amount of power (50 mA) to the TV/Monitor/display-adapter and much more isn't in theory allowed. In fact there is a diode (D1) in series with the power line which can only handle 200 mA, if the adapter tries to draw much more than that the diode might fail. Therefore only externally powered adapters are to be recommended. Despite this, many people report success with non externally powered devices. If you have bought a non externally powered HDMI to VGA adapter, and you experience problems with it (It behaves badly, D1 burns out, F3 "blows", or your PSU overloads), then not all is lost, there are cheap (a few dollars) adapters that allow you to add external power to the HDMI cable! An example can be found here: [13].

HDMI->DVI-D cables

HDMI to DVI-D cables, or HDMI cables with an DVI-D adapters should work, connected to a DVI-D monitor, that is because both HDMI and DVI use the same kind of digital signaling (LVDS). The only limitation being that DVI-D misses the signal channel for audio.

There are three kinds of DVI. There is DVI-D, a digital signal fully compatible with HDMI, so a passive cable can be used. There is DVI-I, which is a connector with both analog pins and digital pins. An HDMI to DVI-D adapter fits in a DVI-I female connector. Finally, there is DVI-A. This a fairly rare connection, but occasionally it will be found on some monitors and is an analog interface, in fact the same as VGA! In any case, you may need to change config.txt hdmi_force_hotplug=0 to =1 if your display does not receive DVI signal (the analog output is likely active).

Some adapters like Farnell part AK-CBHD03-BK are HDMI to DVI-I, which, while not fitting in a DVI-D monitor, are still compatible. The analog pins simply must be bent.

The HDMI to DVI-D cable provided by Apple with the 2010 Mac Mini worked. It does not appear this adapter can be purchased separately.

  • The Pi Hut
  • Other Variants
    • AmazonBasics HDMI to DVI Adapter Cable (model SK231) works and is inexpensive.
    • A generic HDMI-to-DVI converter from eBay. Works well, but it's probably the cause of some power loss between the Raspberry Pi and the monitor, causing this problem. A setting of config_hdmi_boost=5 in /etc/boot solved this. Note that config_hdmi_boost=4, as suggested in the troubleshooting guide, helped, but it did not solve the problem completely.

HDMI->VGA Cables

HDMI to VGA cables do not work! They rely on logic incorporated in a video card that isn't available in a PI. Somehow such a video card outputs analog signal on the otherwise purely digital HDMI connector, that seems to be the only way for it to work. But normally HDMI cables never carry analog signals and the PI surely doesn't output analog signals either, almost no HDMI output device does, as its completely against HDMI specifications.

HDMI->VGA converter boxes

HDMI to VGA converters do work, they convert the digital serial data streams from HDMI and using complex logic, and digital to analog converters they convert the HDMI signal to the analog signals needed for VGA, and sometimes also convert HDMI audio to an analog stereo signal. But note that if they feed off the PI it can cause a problem, as the PI only is designed to provide about 50mA to the (HDMI or DVI-D) monitor, and these adapters use >200mA, while the absolute maximum the PI can let through is 200mA. These adapters also thus use about half the energy that the PI (without USB devices) uses. Therefore its much better to use an adapter that has an external power input. Alternatively there are HDMI dongles (male to female HDMI adapters) that have a barrel input connector to feed the adapter with.

It seems unlikely any of these HDMI->VGA converters could be used for driving a SCART RGB SD CRT TV with a suitable lead (as shown here for ATI/Nvidia PC output http://www.mythtv.org/wiki/RGB_Scart) because they only output preset progressive resolutions, whereas the TV will need an interlaced resolution and probably custom timings.

Most will require use RPi_config.txt. Start off with hdmi_safe=1.

HDMI to VGA + audio adapter from DHgate

  • Under six pounds with free international shipping [14] makes this worth the delivery time of just under 3 weeks. Works out of the box at 1024x768 without editing config.txt (I'll try editing for full HD later). Spec. says upto UXGA and 1080p with 10-bit DAC at 165MHz/1.65Gbps. Raspberry "tvservice -a" reports that it supports audio up to 192k at 24-bit. Sounded fine on my tiny speaker. Comes with 3.5mm stereo plug-to-plug cable and USB to mini barrel jack power cable which it doesn't need on the Pi. Ran mine for ages without the external power and the Pi's HDMI regulator never got more than 34 degrees C. Adapter weighs only 14.8g and can plug directly into the Pi or even via a 90-degree 'elbow' which I prefer to use. VGA signal is good enough to run 2 displays at once using a cheap splitter cable. After brief testing with good headphones, it seems there's some definite noise on a signal of 17,500Hz and 18,500Hz is distorted. In contrast, the RPi's own analogue sounds clean at 17,500Hz. So you couldn't consider this an alternative to a good USB DAC.

HDMI to VGA Cable adaptor from amazon

  • At under ten pounds this one [15] is one of the cheapest, but perhaps due to a more advanced design is seems power frugal enough to most often work well with a Pi, it has many comments saying it works well with the Pi, and gives tips on how to edit config.txt.

HDMI to VGA adapter from amazon - USA

  • This one works with Pi, but does require config.txt edit.

http://www.amazon.com/gp/product/B00JLRHMZE/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 Ableconn HDMI2VGAD Active HDMI to VGA Adapter Converter Dongle for Desktop PC/Notebook up to 1920x1200 / 1920x1080 - HDMI to VGA HD15 monitor Price: $17.99 (Mar. 13, 2015). One photo shows three Pi models connected to VGA monitors. The AbleComm logo is on clear tape wrapped around the adapter, apparently made for "private labeling". So, the item is probably sold by other suppliers too. The adapter is very compact and low-power, unlike some of the other adapters. My ViewSonic VA702b monitor required: hdmi_group=2 -- indicates VGA hdmi_mode=35 -- 1280 x 1024, 60 Hz Prior to those changes, the picture color was mostly red, but readable enough to log in and edit config.txt.

Sanoxy HDMI to VGA converter

  • Sanoxy HDMI to VGA converter, $27 from Amazon, no changes required with official Raspbian Wheezy image (2012-Jul-15), note: had already disabled overscan previously

"Neewer" HDMI to VGA

According to user "Tom1989" the same Neewer HDMI to VGA adapter burned out BAT54 Schottky diode D1 on the Raspberry Pi and broke its HDMI output: Serious HDMI Problems. What's that smell? Burning Raspberry!. On that thread, "mahjongg" suggested the NXP (or equivalent) PMEG2010AET as a high-current replacement for D1. The PMEG2010AET has 1 A max forward current, much greater than the BAT54's 200 mA limit which may be exceeded by your HDMI -> VGA converter. Remember that the converter's current must come from your Raspberry Pi power supply and go through the Micro USB cable and polyfuse F3, so you may get extra voltage drops and/or cause F3 to trip depending on how much current the converter uses. As always with board modifications, YMMV. Also on the same" thread, user "pwinwood" reported the Neewer's current to be 400 mA, which is twice the limit of BAT54 diode D1. "pwinwood" also took the Neewer apart and added its own +5 V connection adapted from a USB cable, which bypasses Raspberry Pi's Micro USB cable and polyfuse F3. Link to a gallery with detailed images & steps of the same adapter modification: HERE --by Pinoccio

"Kanaan" HDMI-VGA

HDMI Male to VGA RGB Female HDMI to VGA Video Converter adapter

HDMI to VGA 3.5mm Audio HDTV HD Video Converter

Sadly the IC's on the PCB have all been scrubbed. In-depth review http://raspi.tv/2013/hdmi-to-vga-video-converter-with-sound-for-raspberry-pi-review. Requires HDMI boost and overscan, config.txt settings for 640x480 @60 Hz:

hdmi_drive=2
hdmi_group=2
hdmi_mode=4
config_hdmi_boost=4
overscan_top=-30
overscan_bottom=-30
overscan_left=-30
overscan_right=-30

HDFuryPro HDMI to YPbBr/VGA Converter

  • HDFuryPro HDMI to YPbBr/VGA Converter found on Amazon -- [16] -- Works with Raspberry Pi. Tested against a Philips 170B 1280x1024 LCD monitor, producing a full native resolution image. Not tested against a Component Video TV yet, and audio has yet to be got working.

The config.txt settings used are:

hdmi_drive=2
hdmi_group=2
hdmi_mode=36
disable_overscan=1

HDFury1 1080p HDMI to VGA Converter

  • HDFury1 1080p HDMI to VGA Converter from HDFury.com. I'm not sure the HDFury1 can be got a hold of easily nowadays, I happened to have access to one to try out. HDFury2, 3 and 4 are available as far as I can tell, but it is very pricey compared to the alternatives. HDFury1 was around £80 when we bought one for a project at work. HDFury2 seems to be around £130, 3 and 4 are getting on towards £200 or more. So not to be recommended as a solution unless you happen to have one lying around. I don't believe there is any relationship between the company that produces these and the HDFuryPro I bought for myself (See above). I didn't alter any config settings, just plugged it in. It doesn't work without having its external power supply connected, as it requires 0.4 A, which is too much draw for the 5 V supply available from the HDMI socket on the Raspberry Pi. Its power LED lights, but no picture is produced. In comparison to the HDFuryPro this picture from this device is sharper, but it is not enough to justify the extra cost.

The config.txt settings used are:

hdmi_drive=2
hdmi_group=2
hdmi_mode=36
disable_overscan=1

Cable Matters Gold Plated Premium HDMI to VGA

Or in the US:

  • http://www.amazon.com/gp/product/B00879DM56 - "Cable Matters Active HDMI to VGA Adapter" I've seen mixed results with this one; it seems to work the very first time I try it on a given monitor, but then I can't seem to get it to work afterwards. I've tried various combinations of the other settings shown in this section with no success.

How to get working if no output: edit config.txt

hdmi_drive=2
hdmi_group=2
hdmi_mode=36 #1280x1024 - change to desired resolution
hdmi_force_hotplug=1

Turn on the RaspberryPi with the adapter plugged into the HDMI port and the microUSB cord plugged into the adapter. Having the microUSB cord plugged in is critical for it to work. With the Pi still on, unplug the adapter from the HDMI port and remove the VGA cable from the adapter. Now unplug usb cord from the adapter and immediately plug back in. Only the microUSB power cord should be plugged in. Now plug the VGA cord back into the adapter. Both the power cord and the VGA cord should be plugged into the adapter. Plug the adapter back into the HDMI port. Now it should be working. From playing around with the device on my laptop I found that the adapter needs power to be able to tell what the resolution of the VGA monitor is. If it is unable to find the VGA resolution it will not work. Unplugging the HDMI, VGA, and power cord seems to reset the device. Plugging the microUSB cable in seems to turn on the device, allowing VGA resolution detection to work. This method will probably work by just starting the Pi with no adapter plugged in, then just plug in the microUSB, VGA, and HDMI cable in that order.

HDMI V1.4 Male to VGA Female Converter Adapter

The config.txt for Raspbian (Flatron VGA monitor 1024 * 768):

hdmi_drive=2
hdmi_group=2
hdmi_mode=16
hdmi_force_hotplug=1
disable_overscan=0

HDMI - VGA [lontium chip]

  • http://cgi.ebay.pl/ws/eBayISAPI.dll?ViewItem&item=251086464644. It is very cheap, but it works perfectly. No config.txt changes was needed at all. I've booted Raspbian and OpenELEC. Monitor is detected correctly and the optimal resolution is set (Raspbian) or you can change the res in the menu (OpenELEC). The /opt/vc/bin/tvservice is able to read monitor edid data. I tested the adapter using NEC 72VM 15" LCD. (1280x1024 60 Hz, 1024x768 60 Hz, 640x480 works) The adapter is based on Lontium LT8511A chip, but I was unable to get the specification for it. The D1 diode is getting very hot though. Most likely the adapter drives more than 200 mA. The standard RS Components 1.2 A USB power supply is able to provide enough power for the Raspberry Pi and the adapter. I'll try to modify the adapter to connect external power to bypass D1.

Pi-View HDMI-VGA converter

  • The "Pi-View" was designed specifically for use with the Raspberry Pi. It does work although the small box gets warm and the video output isn't great (slightly fuzzy text, smaller screen area even with overscan enabled) [17]

DVI-D -> VGA active adapters

None are currently listed

Composite->SCART

SCART adapters (SCART plugs with three RCA connectors in the back), will probably work when used with the yellow RCA plug connected to the Raspberry Pi's RCA video output. Additionally using a splitter cable (3.5 mm jack plug on one end, and red-white RCA plugs on the other end) will probably work when plugged into the red and white (left and right audio channels) of the SCART adapter.

  • Generic - works

Composite->VGA converter boxes

Boblight hardware

Lightberry

  • http://lightberry.eu it's the first (I think), dedicated hardware for Raspberry Pi that can produce colorful effects behind your TV, when you watch movies or even pictures. It uses GPIO pins (not USB). It is easy to configure - you can even download configured system image from the producer website. Works perfectly :)

SD cards

The SD card section has been moved to a separate page. See RPi SD cards

Foreign Language Translations

References

♦ nbsp;V 1nbsp;V 1000