AGL 6.0.0 booting on R-Car H3 not completed

Jump to: navigation, search
Revision as of 24 October 2018 at 02:55.
The highlighted comment was created in this revision.

Hello.
I built AGL 6.0.0 for the R-Car Starter Kit Premier/H3 according to the AGL guide, and tried booting AGL on the R-Car H3. [See "Steps to reproduce"]

But I can not see completing of AGL boot on R-Car H3.
The kernel does not proceed from message of "Waiting for root device /dev/mmcblk1p1...". [See attached "Booting log"]

Please tell me how to solve it.
In case of AGL 6.0.0 booting on M3, I can see completing of AGL boot[the shell is launched and home-screen is shown at hdmi-display].

Steps to reproduce:

1) Download all layers for the for Flounder 6.0.0
 I have performed according to below page:
 https://wiki.automotivelinux.org/agl-distro/release-notes#funky_flounder
 
 $ repo init -b flounder -m flounder_6.0.0.xml -u https://gerrit.automotivelinux.org/gerrit/AGL/AGL-repo
 $ repo sync
2) Building and Booting the AGL for R-Car Starter Kit Premier/H3
 I have performed for machine h3ulcb according to below page:
 http://docs.automotivelinux.org/docs/getting_started/en/dev/reference/machines/R-Car-Starter-Kit-gen3.html
 
 Note) I set "/boot/r8a7795-es1-h3ulcb.dtb" is instead of "/boot/Image-r8a7795-es1-h3ulcb.dtb" becaseu I cannot find "Image-r8a7795-es1-h3ulcb.dtb" on "/boot/".


Booting log:

[    0.000295] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.16
[    0.005858] NOTICE:  BL2: PRR is R-Car H3 Ver1.1
[    0.010440] NOTICE:  BL2: Board is Starter Kit Rev1.0
[    0.015468] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
[    0.020893] NOTICE:  BL2: LCM state is CM
[    0.024936] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
[    0.030919] NOTICE:  BL2: DDR2800(rev.0.27)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.065554] NOTICE:  BL2: DRAM Split is 4ch
[    0.069438] NOTICE:  BL2: QoS is default setting(rev.0.37)
[    0.074939] NOTICE:  BL2: Lossy Decomp areas
[    0.079114] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.086199] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.093111] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.100027] NOTICE:  BL2: v1.3(release):b330e0e
[    0.104516] NOTICE:  BL2: Built : 01:25:08, Jan 24 2018
[    0.109703] NOTICE:  BL2: Normal boot
[    0.113345] NOTICE:  BL2: dst=0xe6320208 src=0x8180000 len=512(0x200)
[    0.119894] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.126352] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.133577] NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
[    0.144057] NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)

U-Boot 2015.04 (Jan 24 2018 - 10:25:14)

CPU: Renesas Electronics R8A7795 rev 1.1
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
Flash: 64 MiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
19347968 bytes read in 3092 ms (6 MiB/s)
69134 bytes read in 14 ms (4.7 MiB/s)
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Using Device Tree in place at 0000000048000000, end 0000000048013e0d

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.0-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Fri Oct 19 01:57:21 UTC 2018
[    0.000000] Boot CPU: AArch64 Processor [411fd073]
[    0.000000] Machine model: Renesas H3ULCB board based on r8a7795 ES1.x
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000073fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x73ff99a00-0x73ff9b4ff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000048000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000073fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
[    0.000000]   node   0: [mem 0x0000000057000000-0x000000007fffffff]
[    0.000000]   node   0: [mem 0x0000000500000000-0x000000053fffffff]
[    0.000000]   node   0: [mem 0x0000000600000000-0x000000063fffffff]
[    0.000000]   node   0: [mem 0x0000000700000000-0x000000073fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff]
[    0.000000] On node 0 totalpages: 1003520
[    0.000000]   DMA zone: 3392 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 217088 pages, LIFO batch:31
[    0.000000]   Normal zone: 12288 pages used for memmap
[    0.000000]   Normal zone: 786432 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS resident on physical CPU 0x0
[    0.000000] random: fast init done
[    0.000000] percpu: Embedded 23 pages/cpu @ffff8006ffede000 s55576 r8192 d30440 u94208
[    0.000000] pcpu-alloc: s55576 r8192 d30440 u94208 alloc=23*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 987840
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
[    0.000000] Memory: 3190236K/4014080K available (11196K kernel code, 1230K rwdata, 5276K rodata, 1152K init, 426K bss, 152100K reserved, 671744K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008b70000   ( 11200 KB)
[    0.000000]     .rodata : 0xffff000008b70000 - 0xffff0000090a0000   (  5312 KB)
[    0.000000]       .init : 0xffff0000090a0000 - 0xffff0000091c0000   (  1152 KB)
[    0.000000]       .data : 0xffff0000091c0000 - 0xffff0000092f3a00   (  1231 KB)
[    0.000000]        .bss : 0xffff0000092f3a00 - 0xffff00000935e550   (   427 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000200000 - 0xffff7e001c000000   (   446 MB actual)
[    0.000000]     memory  : 0xffff800008000000 - 0xffff800700000000   ( 28544 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f102f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
[    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
[    0.000357] Console: colour dummy device 80x25
[    0.000399] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
[    0.000407] pid_max: default: 32768 minimum: 301
[    0.000449] Security Framework initialized
[    0.000458] Smack:  Initializing.
[    0.000461] Smack:  IPv6 port labeling enabled.
[    0.002078] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.002886] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002929] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002961] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.015963] ASID allocator initialised with 65536 entries
[    0.023952] Hierarchical SRCU implementation.
[    0.032444] Detected Renesas R-Car Gen3 r8a7795 ES1.1
[    0.033480] EFI services will not be available.
[    0.039974] smp: Bringing up secondary CPUs ...
[    0.068129] Detected PIPT I-cache on CPU1
[    0.068172] CPU1: Booted secondary processor [411fd073]
[    0.096136] Detected PIPT I-cache on CPU2
[    0.096154] CPU2: Booted secondary processor [411fd073]
[    0.124164] Detected PIPT I-cache on CPU3
[    0.124182] CPU3: Booted secondary processor [411fd073]
[    0.152106] psci: failed to boot CPU4 (-22)
[    0.152119] CPU4: failed to boot: -22
[    0.152123] CPU4: failed in unknown state : 0x0
[    0.180134] psci: failed to boot CPU5 (-22)
[    0.180138] CPU5: failed to boot: -22
[    0.180141] CPU5: failed in unknown state : 0x0
[    0.208166] psci: failed to boot CPU6 (-22)
[    0.208170] CPU6: failed to boot: -22
[    0.208174] CPU6: failed in unknown state : 0x0
[    0.236196] psci: failed to boot CPU7 (-22)
[    0.236200] CPU7: failed to boot: -22
[    0.236204] CPU7: failed in unknown state : 0x0
[    0.236233] smp: Brought up 1 node, 4 CPUs
[    0.236237] SMP: Total of 4 processors activated.
[    0.236242] CPU features: detected feature: 32-bit EL0 Support
[    0.236354] CPU: All CPU(s) started at EL2
[    0.236890] devtmpfs: initialized
[    0.241742] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.241802] futex hash table entries: 2048 (order: 6, 262144 bytes)
[    0.249675] pinctrl core: initialized pinctrl subsystem
[    0.251047] DMI not present or invalid.
[    0.251298] NET: Registered protocol family 16
[    0.252559] cpuidle: using governor menu
[    0.253416] vdso: 2 pages (1 code @ ffff000008b76000, 1 data @ ffff0000091c5000)
[    0.253429] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.253964] DMA: preallocated 256 KiB pool for atomic allocations
[    0.254199] Serial: AMBA PL011 UART driver
[    0.257329] sh-pfc e6060000.pin-controller: r8a77950_pfc support registered
[    0.277022] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.277982] ACPI: Interpreter disabled.
[    0.279989] rcar-cpufreq: use avs value: 0
[    0.280002] rcar-cpufreq: /cpus/cpu@0 is running with: /opp_table0
[    0.280010] rcar-cpufreq: /cpus/cpu@1 is running with: /opp_table0
[    0.280017] rcar-cpufreq: /cpus/cpu@2 is running with: /opp_table0
[    0.280023] rcar-cpufreq: /cpus/cpu@3 is running with: /opp_table0
[    0.281259] vgaarb: loaded
[    0.281426] SCSI subsystem initialized
[    0.281548] libata version 3.00 loaded.
[    0.281708] usbcore: registered new interface driver usbfs
[    0.281732] usbcore: registered new interface driver hub
[    0.281789] usbcore: registered new device driver usb
[    0.282679] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
[    0.283007] media: Linux media interface: v0.10
[    0.283028] Linux video capture interface: v2.00
[    0.283094] pps_core: LinuxPPS API ver. 1 registered
[    0.283098] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.283109] PTP clock support registered
[    0.283336] EDAC MC: Ver: 3.0.0
[    0.283481] dmi: Firmware registration failed.
[    0.284052] Advanced Linux Sound Architecture Driver Initialized.
[    0.284296] NetLabel: Initializing
[    0.284301] NetLabel:  domain hash size = 128
[    0.284304] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.284340] NetLabel:  unlabeled traffic allowed by default
[    0.284628] clocksource: Switched to clocksource arch_sys_counter
[    0.284741] VFS: Disk quotas dquot_6.6.0
[    0.284779] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.284880] pnp: PnP ACPI: disabled
[    0.290375] NET: Registered protocol family 2
[    0.290883] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.291028] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.291290] TCP: Hash tables configured (established 32768 bind 32768)
[    0.291416] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.291447] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.291569] NET: Registered protocol family 1
[    0.291814] RPC: Registered named UNIX socket transport module.
[    0.291818] RPC: Registered udp transport module.
[    0.291822] RPC: Registered tcp transport module.
[    0.291825] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291833] PCI: CLS 0 bytes, default 128
[    0.292536] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
[    0.292683] hw perfevents: /soc/pmu_a53: failed to probe PMU!
[    0.292689] hw perfevents: /soc/pmu_a53: failed to register PMU devices!
[    0.293028] kvm [1]: 8-bit VMID
[    0.293032] kvm [1]: IDMAP page: 48b57000
[    0.293036] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    0.293770] kvm [1]: vgic-v2@f1040000
[    0.293828] kvm [1]: vgic interrupt IRQ1
[    0.293838] kvm [1]: virtual timer IRQ4
[    0.293892] kvm [1]: Hyp mode initialized successfully
[    0.295643] audit: initializing netlink subsys (disabled)
[    0.295726] audit: type=2000 audit(0.291:1): state=initialized audit_enabled=0 res=1
[    0.295950] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    0.299072] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.299470] NFS: Registering the id_resolver key type
[    0.299491] Key type id_resolver registered
[    0.299495] Key type id_legacy registered
[    0.299503] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.299631] 9p: Installing v9fs 9p2000 file system support
[    0.301093] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.301101] io scheduler noop registered
[    0.301199] io scheduler cfq registered (default)
[    0.301204] io scheduler mq-deadline registered
[    0.301208] io scheduler kyber registered
[    0.306365] gpio_rcar e6050000.gpio: driving 16 GPIOs
[    0.306594] gpio_rcar e6051000.gpio: driving 28 GPIOs
[    0.306797] gpio_rcar e6052000.gpio: driving 15 GPIOs
[    0.306996] gpio_rcar e6053000.gpio: driving 16 GPIOs
[    0.307180] gpio_rcar e6054000.gpio: driving 18 GPIOs
[    0.307378] gpio_rcar e6055000.gpio: driving 26 GPIOs
[    0.307569] gpio_rcar e6055400.gpio: driving 32 GPIOs
[    0.307765] gpio_rcar e6055800.gpio: driving 4 GPIOs
[    0.326177] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.327725] SuperH (H)SCI(F) driver initialized
[    0.328146] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 139, base_baud = 0) is a scif
[    1.424882] console [ttySC0] enabled
[    1.429315] msm_serial: driver initialized
[    1.434422] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.441043] [drm] No driver support for vblank timestamp query.
[    1.447499] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.457336] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.470891] brd: module loaded
[    1.478402] loop: module loaded
[    1.494743] libphy: Fixed MDIO Bus: probed
[    1.499093] tun: Universal TUN/TAP device driver, 1.6
[    1.505151] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.511170] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.517131] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.524107] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.529704] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    1.537536] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.543801] sky2: driver version 1.30
[    1.548255] ravb e6800000.ethernet: no valid MAC address supplied, using a random one
[    1.556152] libphy: ravb_mii: probed
[    1.560769] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 62:ee:99:bb:a7:a4, IRQ 136.
[    1.570101] VFIO - User Level meta-driver version: 0.3
[    1.576303] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.582834] ehci-pci: EHCI PCI platform driver
[    1.587299] ehci-platform: EHCI generic platform driver
[    1.592799] ehci-platform ee0a0100.usb: EHCI Host Controller
[    1.598473] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1
[    1.606445] ehci-platform ee0a0100.usb: irq 146, io mem 0xee0a0100
[    1.628637] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
[    1.635158] hub 1-0:1.0: USB hub found
[    1.638920] hub 1-0:1.0: 1 port detected
[    1.643102] ehci-orion: EHCI orion driver
[    1.647241] ehci-exynos: EHCI EXYNOS driver
[    1.651508] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[    1.657151] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.663361] ohci-pci: OHCI PCI platform driver
[    1.667839] ohci-platform: OHCI generic platform driver
[    1.673225] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
[    1.679936] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2
[    1.687847] ohci-platform ee0a0000.usb: irq 146, io mem 0xee0a0000
[    1.782910] hub 2-0:1.0: USB hub found
[    1.786671] hub 2-0:1.0: 1 port detected
[    1.790813] ohci-exynos: OHCI EXYNOS driver
[    1.795547] usbcore: registered new interface driver usb-storage
[    1.801603] usbcore: registered new interface driver usbserial
[    1.807453] usbcore: registered new interface driver usbserial_generic
[    1.813992] usbserial: USB Serial support registered for generic
[    1.822387] i2c /dev entries driver
[    1.833146] cs2000-cp 2-004f: revision - C1
[    1.837376] i2c-rcar e6510000.i2c: probed
[    1.846003] i2c-rcar e66d8000.i2c: probed
[    1.850492] usbcore: registered new interface driver i2c-tiny-usb
[    1.858064] imr fe860000.imr-lx4: IMR device (pdev: -1) registered as /dev/video0
[    1.865757] imr fe870000.imr-lx4: IMR device (pdev: -1) registered as /dev/video1
[    1.873387] imr fe880000.imr-lx4: IMR device (pdev: -1) registered as /dev/video2
[    1.881003] imr fe890000.imr-lx4: IMR device (pdev: -1) registered as /dev/video3
[    1.892080] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values
[    1.904493] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
[    1.915812] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
[    1.927080] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
[    1.936207] sdhci: Secure Digital Host Controller Interface driver
[    1.942394] sdhci: Copyright(c) Pierre Ossman
[    1.947274] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    1.953425] Synopsys Designware Multimedia Card Interface Driver
[    1.960174] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.967100] ledtrig-cpu: registered to indicate activity on CPUs
[    1.974050] usbcore: registered new interface driver usbhid
[    1.979626] usbhid: USB HID core driver
[    1.984346] optee: probing for conduit method from DT.
[    1.984651] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.996781] R-Car Rev.1.0.8
[    1.999890] optee: initialized driver
[    2.004952] usbcore: registered new interface driver snd-usb-audio
[    2.019227] rcar_sound ec500000.sound: probed
[    2.023915] NET: Registered protocol family 17
[    2.028422] 9pnet: Installing 9P2000 support
[    2.032739] Key type dns_resolver registered
[    2.037915] registered taskstats version 1
[    2.047017] thermal emergency: set temperature to 110 celsius
[    2.052832] thermal emergency: shutdown target cpus 1-3
[    2.058056] thermal emergency: freq scaled target cpus 0
[    2.063668] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
[    2.071503] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.078129] [drm] No driver support for vblank timestamp query.
[    2.147727] hub 1-1:1.0: USB hub found
[    2.151652] hub 1-1:1.0: 4 ports detected
[    2.251577] Console: switching to colour frame buffer device 240x67
[    2.274840] rcar-du feb00000.display: fb0:  frame buffer device
[    2.280995] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
[    2.288740] [drm] Device feb00000.display probed
[    2.294385] bd9571mwv 7-0030: Device: BD9571MWV rev. 1
[    2.304694] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    2.372989] renesas_sdhi_internal_dmac ee100000.sd: mmc0 base at 0xee100000 max clock rate 200 MHz
[    2.383200] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok
[    2.390356] asoc-simple-card sound: ASoC: no DMI vendor name!
[    2.398750] input: keyboard as /devices/platform/keyboard/input/input0
[    2.405480] hctosys: unable to open rtc device (rtc0)
[    2.411026] ALSA device list:
[    2.413997]   #0: Loopback 1
[    2.416875]   #1: ak4613
[    2.419744] Waiting 2 sec before mounting root device...
[    2.460636] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[    2.596971] input: ILITEK Multi-Touch-V5100 as /devices/platform/soc/ee0a0100.usb/usb1/1-1/1-1.1/1-1.1:1.0/0003:222A:011E.0001/input/input1
[    2.609611] hid-multitouch 0003:222A:011E.0001: input: USB HID v1.10 Device [ILITEK Multi-Touch-V5100] on usb-ee0a0100.usb-1.1/input0
[    2.622380] hid-generic 0003:222A:011E.0002: device has no listeners, quitting
[    2.686881] mmc0: new ultra high speed SDR104 SDHC card at address aaaa
[    2.693689] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[    2.701819]  mmcblk0: p1
[    2.720635] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[    4.448658] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[    4.456436] Waiting for root device /dev/mmcblk1p1...
    01:35, 22 October 2018

    Hi, I report because this issue progress has changed.

    I seemed that the U-boot parameters(discribed at http://docs.automotivelinux.org/docs/getting_started/en/dev/reference/machines/R-Car-Starter-Kit-gen3.html) were wrong from the previous Booting log.

    [ 2.693689] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
    [ 2.701819] mmcblk0: p1
    [ 2.720635] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
    [ 4.448658] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
    [ 4.456436] Waiting for root device /dev/mmcblk1p1...
    

    So, I tried changing the device name from "/dev/mmcblk1p1" to "/dev/mmcblk0p1".
    And reboot, the shell is launched completely but home-screen is not shown at hdmi-display yet.
    The kernel outputs trace log of WARNING below.

    [ 16.128912] -----------[ cut here ]-----------
    [ 16.133663] WARNING: CPU: 1 PID: 54 at /mnt/AGL/workspace_agl_ff_6.0.0_rcar/build-h3/tmp/work/h3ulcb-agl-linux/kernel-module-gles/1.0-r0/rogue_km/binary_r8a7795_linux_release/target_aarch64/kbuild/services/server/devices/rgx/rgxfwutils.c:4115 RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
    [ 16.160150] Modules linked in: can_bcm can bnep nfc btwilink st_drv bluetooth ecdh_generic rfkill crc32_ce crct10dif_ce pvrsrvkm(O) vspm_if(O) vsp2(O) vspm(O) uvcs_drv(O) mmngrbuf(O) mmngr(O) hdm_usb(O) hdm_i2c(O) hdm_dim2(O) aim_v4l2(O) aim_sound(O) aim_network(O) aim_cdev(O) mostcore(O) ipv6
    [ 16.186172] CPU: 1 PID: 54 Comm: kworker/u16:2 Tainted: G O 4.14.0-yocto-standard #1
    [ 16.195037] Hardware name: Renesas H3ULCB board based on r8a7795 ES1.x (DT)
    [ 16.202108] Workqueue: pvr_workqueue MISRWrapper [pvrsrvkm]
    [ 16.207676] task: ffff8006fae20000 task.stack: ffff000009b40000
    [ 16.213698] PC is at RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
    [ 16.219761] LR is at RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
    [ 16.225676] pc : [<ffff000000ce6e28>] lr : [<ffff000000ce6e28>] pstate: 60000145
    [ 16.233063] sp : ffff000009b43d60
    [ 16.236371] x29: ffff000009b43d60 x28: 0000000000000000
    [ 16.241680] x27: 0000000000000000 x26: ffff0000210790a0
    [ 16.246988] x25: 0000000070014008 x24: ffff8006f4a705e8
    [ 16.252296] x23: ffff000000d45618 x22: ffff8006f4a70000
    [ 16.257603] x21: ffff000021079080 x20: 0000000000000020
    [ 16.262911] x19: ffff000021079040 x18: 0000000000000010
    [ 16.268219] x17: 00000000000012c8 x16: 00000000000012cc
    [ 16.273526] x15: 0000000000000001 x14: 0000000000000400
    [ 16.278833] x13: 0000000000000400 x12: 0000000000000000
    [ 16.284141] x11: 0000000000000005 x10: 0000000000000000
    [ 16.289448] x9 : 00000000006cd4b7 x8 : ffff8006ffeea6c0
    [ 16.294756] x7 : ffff8006ffeea668 x6 : 00000000000000a7
    [ 16.300063] x5 : 0000000000000001 x4 : ffff0000091d2c00
    [ 16.305370] x3 : 00000000000f4240 x2 : ffff8006fa5e7088
    [ 16.310678] x1 : 0000000000000000 x0 : 0000000000000002
    [ 16.315986] Call trace:
    [ 16.318427] Exception stack(0xffff000009b43c20 to 0xffff000009b43d60)
    [ 16.324862] 3c20: 0000000000000002 0000000000000000 ffff8006fa5e7088 00000000000f4240
    [ 16.332684] 3c40: ffff0000091d2c00 0000000000000001 00000000000000a7 ffff8006ffeea668
    [ 16.340507] 3c60: ffff8006ffeea6c0 00000000006cd4b7 0000000000000000 0000000000000005
    [ 16.348329] 3c80: 0000000000000000 0000000000000400 0000000000000400 0000000000000001
    [ 16.356152] 3ca0: 00000000000012cc 00000000000012c8 0000000000000010 ffff000021079040
    [ 16.363974] 3cc0: 0000000000000020 ffff000021079080 ffff8006f4a70000 ffff000000d45618
    [ 16.371796] 3ce0: ffff8006f4a705e8 0000000070014008 ffff0000210790a0 0000000000000000
    [ 16.379619] 3d00: 0000000000000000 ffff000009b43d60 ffff000000ce6e28 ffff000009b43d60
    [ 16.387441] 3d20: ffff000000ce6e28 0000000060000145 ffff000009b43d60 ffff000000ce6e28
    [ 16.395263] 3d40: ffffffffffffffff 0000000000000020 ffff000009b43d60 ffff000000ce6e28
    [ 16.403248] [<ffff000000ce6e28>] RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
    [ 16.410302] [<ffff000000ce893c>] RGX_MISRHandler+0x24/0x38 [pvrsrvkm]
    [ 16.416840] [<ffff000000cb5058>] MISRWrapper+0x18/0x20 [pvrsrvkm]
    [ 16.422935] [<ffff0000080e06bc>] process_one_work+0x1d4/0x348
    [ 16.428675] [<ffff0000080e0878>] worker_thread+0x48/0x470
    [ 16.434070] [<ffff0000080e6b64>] kthread+0x12c/0x130
    [ 16.439033] [<ffff000008084c10>] ret_from_fork+0x10/0x18
    [ 16.444339] --[ end trace da55878e442ea43e ]--
    

    I should do something else?
    Perhaps, my knowledge may be missing, but I appreciate if someone let me know advice to solve it.

      19:55, 23 October 2018