Firmware update hangs

Jump to: navigation, search

Issue is not yet resolved, please see log below.


H3 SAMPLE LOADER V1.17 2016.11.08 

CPU   : AArch64 CA57
DRAM  : LPDDR4 DDR3200
DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT  : Normal Boot
Backup: DDR Cold Boot

jump to 0xE6330000

H3 MiniMonitor V0.24 2016.11.08 

Work Memory SystemRAM (H'E6328000-H'E632FFFF)

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory. 

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6320000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'0

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!

= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000
SpiFlashMemory End Address  : H'00000E67
===============================================[edit]

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory. 

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'44000000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'1C0000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error 

SpiFlashMemory Stat Address : H'001C0000
SpiFlashMemory End Address  : H'105C05D3

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory. 

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6302000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'40000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)

KarthikShanmugam (talk)

‎01:25, 8 June 2017

You do not have permission to edit this page, for the following reasons:

  • The action you have requested is limited to users in the group: Users.
  • You must confirm your email address before editing pages. Please set and validate your email address through your user preferences.

You can view and copy the source of this page.

Return to Thread:Talk:R-Car/Boards/Yocto-Gen3/Firmware update hangs/reply (5).

 
Retrieved from "https://elinux.org/Thread:Talk:R-Car/Boards/Yocto-Gen3/Firmware_update_hangs/reply_(4)#Firmware_update_hangs_3116"