|
|
| (24 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | == Get Prepared ==
| + | Move to https://elinux.org/Jetson/l4t/Camera_BringUp |
| − | * Please read through "Camera Development" section in https://developer.nvidia.com/embedded/dlc/l4t-documentation-28-1
| |
| − | == FAQ ==
| |
| − | === Tips for debugging ===
| |
| − | | |
| − | '''TX1'''
| |
| − | * if you saw below error message
| |
| − | tegra-vi4 15700000.vi: PXL_SOF syncpt timeout! err = -11
| |
| − | | |
| − | * please check below 4 items in your sensor device tree, these should follow the settings in your sensor datasheet
| |
| − | mode0 {
| |
| − | cil_settletime = "0";
| |
| − | active_w = "1920";
| |
| − | active_h = "1080";
| |
| − | embedded_metadata_height = "1";
| |
| − | | |
| − | * if you saw below error message
| |
| − | video4linux video0: MW_ACK_DONE syncpoint time out!
| |
| − | | |
| − | * Enable the csi debug message from below command, and use v4l2-ctl to verify the driver first.
| |
| − | sudo su
| |
| − | cd /sys/kernel/debug/dynamic_debug/
| |
| − | echo file csi2_fops.c +p > control
| |
| − | | |
| − | v4l2-ctl -d /dev/video0 --set-ctrl bypass_mode=0 --stream-mmap --stream-count=3
| |
| − | | |
| − | * please check below
| |
| − | please review the configuration of "line_length" in sensor driver
| |
| − | try to increase the delay between video lines data send via CSI
| |
| − | review the sensor datasheet to check the settings of FPS range
| |
| − | | |
| − | | |
| − | | |
| − | | |
| − | '''TX2'''
| |
| − | * if you saw below message it could be the sensor output embedded data line but DT didn't declare embedded_metadata_height or it value is 0
| |
| − | arm-smmu 12000000.iommu: Unhandled context fault: iova=0x00000000, fsynr=0x200011, cb=19, sid=4(0x4 - VI), pgd=0, pud=0, pmd=0, pte=0
| |
| − | | |
| − | <br />
| |
| − | === Steps to enable more debug messages ===
| |
| − | * To enable trace for more information
| |
| − | echo 1 > /sys/kernel/debug/tracing/tracing_on
| |
| − | echo 30720 > /sys/kernel/debug/tracing/buffer_size_kb
| |
| − | echo 1 > /sys/kernel/debug/tracing/events/tegra_rtcpu/enable
| |
| − | echo 1 > /sys/kernel/debug/tracing/events/freertos/enable
| |
| − | echo 2 > /sys/kernel/debug/camrtc/log-level
| |
| − | echo > /sys/kernel/debug/tracing/trace
| |
| − | cat /sys/kernel/debug/tracing/trace
| |
| − | | |
| − | | |
| − | It could be CRC error at frame end package. Please contact with sensor vendor to check the CRC header.
| |
| − | kworker/0:1-2059 [000] ...1 434.733650: rtcpu_vinotify_handle_msg: tstamp:13948014423 tag:CSIMUX_FRAME channel:0x00 frame:2 vi_tstamp:1063112012 data:0x00400060
| |
| − | kworker/0:1-2059 [000] ...1 434.733654: rtcpu_vinotify_handle_msg: tstamp:13949051348 tag:CSIMUX_FRAME channel:0x00 frame:3 vi_tstamp:1064148939 data:0x00400060
| |
| − | | |
| − | | |
| − | It could be the pix_clk_hz in DT too small cause the ISP can't handle the input.
| |
| − | kworker/5:2-248 [005] ...1 297.951130: rtcpu_vinotify_handle_msg: tstamp:9663302491 tag:CSIMUX_FRAME channel:0x00 frame:13 vi_tstamp:1073367484 data:0x00400062
| |
| − | kworker/5:2-248 [005] ...1 297.951133: rtcpu_vinotify_handle_msg: tstamp:9663324801 tag:ISPBUF_FS channel:0x00 frame:14 vi_tstamp:1073389804 data:0x00000000
| |
| − | kworker/5:2-248 [005] ...1 297.951133: rtcpu_vinotify_handle_msg: tstamp:9663335039 tag:CHANSEL_PXL_SOF channel:0x00 frame:14 vi_tstamp:1073400039 data:0x00000001
| |
| − | kworker/5:2-248 [005] ...1 297.951134: rtcpu_vinotify_handle_msg: tstamp:9664344311 tag:CHANSEL_SHORT_FRAME channel:0x04 frame:14 vi_tstamp:1074409154 data:0x00000001
| |
| − | kworker/5:2-248 [005] ...1 297.951135: rtcpu_vinotify_handle_msg: tstamp:9664344499 tag:ISPBUF_FE channel:0x00 frame:14 vi_tstamp:1074409155 data:0x00000000
| |
| − | OR
| |
| − | kworker/5:3-1359 [005] ...1 253.671469: rtcpu_vinotify_handle_msg: tstamp:8279208283 tag:CSIMUX_FRAME channel:0x03 frame:1276 vi_tstamp:3984240577 data:0x000004a2
| |
| − | kworker/5:3-1359 [005] ...1 253.671476: rtcpu_vinotify_handle_msg: tstamp:8279969727 tag:CHANSEL_PXL_SOF channel:0x00 frame:12340 vi_tstamp:3985001693 data:0x00000001
| |
| − | kworker/5:3-1359 [005] ...1 253.671478: rtcpu_vinotify_handle_msg: tstamp:8279969890 tag:ISPBUF_FIFO_OVERFLOW channel:0x00 frame:12340 vi_tstamp:3985001981 data:0x00000000
| |
| − | kworker/5:3-1359 [005] ...1 253.671481: rtcpu_vinotify_handle_msg: tstamp:8279970411 tag:CHANSEL_FAULT channel:0x00 frame:12340 vi_tstamp:3985001998 data:0x00000100
| |
| − | | |
| − | Lose the FE package cause the FS_FAULT
| |
| − | kworker/4:0-30 [004] ...1 241.772651: rtcpu_vinotify_handle_msg: tstamp:7868711648 tag:CSIMUX_FRAME channel:0x00 frame:1 vi_tstamp:3573743671 data:0x000000a0
| |
| − | kworker/4:0-30 [004] ...1 241.772656: rtcpu_vinotify_handle_msg: tstamp:7868712008 tag:ATOMP_FE channel:0x00 frame:1 vi_tstamp:3573743672 data:0x00000000
| |
| − | | |
| − | The trace show the 0x0ada0040 0x40 means CHANSEL_FAULT of PIXEL_RUNAWAY means VI receives more lines than expected. The 0xad9(2778) is the lines report from the sensor driver.
| |
| − | kworker/5:2-275 [005] ...1 122.290528: rtcpu_vinotify_handle_msg: tstamp:4155862787 tag:CHANSEL_PXL_SOF channel:0x00 frame:0 vi_tstamp:4155862337 data:0x00000001
| |
| − | kworker/5:2-275 [005] ...1 122.290531: rtcpu_vinotify_handle_msg: tstamp:4155867990 tag:CHANSEL_LOAD_FRAMED channel:0x01 frame:0 vi_tstamp:4155867544 data:0x08000000
| |
| − | kworker/5:2-275 [005] ...1 122.342572: rtcpu_vinotify_handle_msg: tstamp:4156521216 tag:CHANSEL_PXL_EOF channel:0x00 frame:0 vi_tstamp:4156520630 data:0x0ad90002
| |
| − | kworker/5:2-275 [005] ...1 122.342579: rtcpu_vinotify_handle_msg: tstamp:4156521395 tag:CHANSEL_FAULT channel:0x00 frame:0 vi_tstamp:4156520667 data:0x0ada0040
| |
| − | kworker/5:2-275 [005] ...1 122.342582: rtcpu_vinotify_handle_msg: tstamp:4156522342 tag:CHANSEL_LOAD_FRAMED channel:0x01 frame:0 vi_tstamp:4156521558 data:0x08000000
| |
| − | kworker/5:2-275 [005] ...1 122.342585: rtcpu_vinotify_handle_msg: tstamp:4156522509 tag:CHANSEL_FAULT_FE channel:0x01 frame:0 vi_tstamp:4156521559 data:0x00000001
| |
| − | kworker/5:2-275 [005] ...1 122.342588: rtcpu_vinotify_handle_msg: tstamp:4156522706 tag:ATOMP_FE channel:0x00 frame:0 vi_tstamp:4156521562 data:0x00000000
| |
| − | | |
| − | Didn't receive any package from the MIPI bus. Make sure the sensor have output data to the MIPI bus
| |
| − | kworker/5:2-2980 [005] ...1 4162.509492: rtos_queue_peek_from_isr_failed: tstamp:130384213094 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4162.509496: rtcpu_start: tstamp:130384214513
| |
| − | kworker/5:2-2980 [005] ...1 4162.665213: rtos_queue_peek_from_isr_failed: tstamp:130389214019 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4162.821197: rtos_queue_peek_from_isr_failed: tstamp:130394214523 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4162.977226: rtos_queue_peek_from_isr_failed: tstamp:130399215027 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.133208: rtos_queue_peek_from_isr_failed: tstamp:130404215532 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.289207: rtos_queue_peek_from_isr_failed: tstamp:130409216052 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.445214: rtos_queue_peek_from_isr_failed: tstamp:130414216548 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.601218: rtos_queue_peek_from_isr_failed: tstamp:130419217056 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.757169: rtos_queue_peek_from_isr_failed: tstamp:130424217548 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4163.913235: rtos_queue_peek_from_isr_failed: tstamp:130429218108 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.069227: rtos_queue_peek_from_isr_failed: tstamp:130434218588 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.225233: rtos_queue_peek_from_isr_failed: tstamp:130439219082 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.433230: rtos_queue_peek_from_isr_failed: tstamp:130444219591 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.589207: rtos_queue_peek_from_isr_failed: tstamp:130449220105 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.745237: rtos_queue_peek_from_isr_failed: tstamp:130454220607 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4164.901226: rtos_queue_peek_from_isr_failed: tstamp:130459221117 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.057232: rtos_queue_peek_from_isr_failed: tstamp:130464221618 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.213244: rtos_queue_peek_from_isr_failed: tstamp:130469222134 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.369261: rtos_queue_peek_from_isr_failed: tstamp:130474222666 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.525261: rtos_queue_peek_from_isr_failed: tstamp:130479223151 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.681253: rtos_queue_peek_from_isr_failed: tstamp:130484223652 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.837312: rtos_queue_peek_from_isr_failed: tstamp:130489224156 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4165.993240: rtos_queue_peek_from_isr_failed: tstamp:130494224659 queue:0x0b4a3c58
| |
| − | kworker/5:2-2980 [005] ...1 4166.149247: rtos_queue_peek_from_isr_failed: tstamp:130499225165 queue:0x0b4a3c58
| |
| − | | |
| − | Possible the sensor didn't send the ECC package.
| |
| − | kworker/4:0-2238 [004] ...1 543.467972: rtcpu_vinotify_handle_msg: tstamp:17333540584 tag:CSIMUX_FRAME channel:0x00 frame:0 vi_tstamp:153670980 data:0x00200060
| |
| − | kworker/4:0-2238 [004] ...1 543.467974: rtcpu_vinotify_handle_msg: tstamp:17334081008 tag:CHANSEL_PXL_SOF channel:0x00 frame:0 vi_tstamp:154211277 data:0x00000001
| |
| − | kworker/4:0-2238 [004] ...1 543.467975: rtcpu_vinotify_handle_msg: tstamp:17334081160 tag:ATOMP_FS channel:0x00 frame:0 vi_tstamp:154211284 data:0x00000000
| |
| − | kworker/4:0-2238 [004] ...1 543.519967: rtcpu_vinotify_handle_msg: tstamp:17334580776 tag:CHANSEL_PXL_EOF channel:0x00 frame:0 vi_tstamp:154711180 data:0x04370002
| |
| − | kworker/4:0-2238 [004] ...1 543.519971: rtcpu_vinotify_handle_msg: tstamp:17334582405 tag:CSIMUX_FRAME channel:0x00 frame:0 vi_tstamp:154712647 data:0x00200060
| |
| − | Can try disable the ECC check.
| |
| − | <source lang="cpp" line start="2" highlight="4-6">
| |
| − | diff --git a/drivers/media/platform/tegra/camera/csi/csi4_fops.c b/drivers/media/platform/tegra/camera/csi/csi4_fops.c
| |
| − | index 0377d7b..b3d01d3 100644
| |
| − | --- a/drivers/media/platform/tegra/camera/csi/csi4_fops.c
| |
| − | +++ b/drivers/media/platform/tegra/camera/csi/csi4_fops.c
| |
| − | @@ -76,8 +76,18 @@ static void csi4_stream_init(struct tegra_csi_channel *chan, int port_num)
| |
| − | csi4_stream_write(chan, port_num, INTR_STATUS, 0x3ffff);
| |
| − | csi4_stream_write(chan, port_num, ERR_INTR_STATUS, 0x7ffff);
| |
| − | csi4_stream_write(chan, port_num, ERROR_STATUS2VI_MASK, 0x0);
| |
| − | - csi4_stream_write(chan, port_num, INTR_MASK, 0x0);
| |
| − | - csi4_stream_write(chan, port_num, ERR_INTR_MASK, 0x0);
| |
| − | +
| |
| − | + csi4_stream_write(chan, port_num, INTR_MASK, PH_ECC_MULTI_BIT_ERR |
| |
| − | + PD_CRC_ERR_VC0 | PH_ECC_SINGLE_BIT_ERR_VC0);
| |
| − | + csi4_stream_write(chan, port_num, ERR_INTR_MASK, PH_ECC_MULTI_BIT_ERR |
| |
| − | + PD_CRC_ERR_VC0 | PH_ECC_SINGLE_BIT_ERR_VC0);
| |
| − | + csi4_stream_write(chan, port_num, ERROR_STATUS2VI_MASK,
| |
| − | + CFG_ERR_STATUS2VI_MASK_VC0 |
| |
| − | + CFG_ERR_STATUS2VI_MASK_VC1 |
| |
| − | + CFG_ERR_STATUS2VI_MASK_VC2 |
| |
| − | + CFG_ERR_STATUS2VI_MASK_VC3);
| |
| − | }
| |
| − | </source>
| |
| − |
| |
| − | | |
| − | * To enable logs from user-space for more details
| |
| − | sudo su
| |
| − | kill the process of argus_daemon or nvcamera-daemon
| |
| − | export enableCamPclLogs=5
| |
| − | export enableCamScfLogs=5
| |
| − | /usr/sbin/argus_daemon option for argus
| |
| − | /usr/sbin/nvcamera-daemon option for gst-launch
| |
| − |
| |
| − | launch camera from another console
| |
